WITHDRAWN: Effect of Al-5Ti-1B master alloy and heat treatment conditions on the mechanical properties and dry sliding wear behavior of an Al–Zn–Mg–Cu aluminum alloy produced by SIMA process

2012 ◽  
Author(s):  
Mohammad Alipour ◽  
Baharak Ghorbanian Aghdam ◽  
Hamid Ebrahimi Rahnoma ◽  
Hossain Razmi(Maani)
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
Master Alloy ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Treatment Conditions ◽  
Sima Process

Investigation on Mechanical Properties and Analysis of Dry Sliding Wear Behavior of Al LM13/AlN Metal Matrix Composite Based on Taguchi's Technique

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
N. Radhika ◽  
R. Raghu
Keyword(s):  
Regression Analysis ◽  
Aluminum Alloy ◽  
Tensile Test ◽  
Metal Matrix ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Ratio Analysis ◽  
Sliding Distance

LM13/AlN (10 wt. %) metal matrix composites (MMC) and unreinforced aluminum alloy were produced under stir casting route. Microstructural characteristics were examined on the developed composite using optical microscope. The hardness and tensile test were carried out on both unreinforced aluminum alloy and composite using Vickers hardness tester and universal testing machine (UTM), respectively. Dry sliding wear behavior of the composite and unreinforced aluminum alloy was evaluated using pin-on-disk tribometer based on the design of experiments approach. Experimental parameters such as applied load (10, 20, and 30 N), velocity (1, 2, and 3 m/s), and sliding distance (500, 1000, and 1500 m) were varied for three levels. Signal-to-noise (S/N) ratio analysis, analysis of variance, and regression analysis were also performed. The characterization results showed that reinforcement particles were uniformly distributed in the composite. The hardness and tensile test revealed greater improvement of property in composite compared to that of unreinforced alloy. Wear plot showed that wear was increased with increase in load and decreased with increase in velocity and sliding distance. S/N ratio analysis and analysis of variance (ANOVA) indicated that load has greater significance over the wear rate followed by velocity and sliding distance. Regression analysis revealed greater adequacy with the constructed model in predicting the wear behavior of composite and unreinforced aluminum alloy. Scanning electron microscopy (SEM) analysis is evident that the transition of wear from mild to severe occurred on increase of the load in the composite.

scholarly journals Dry sliding wear behavior of AA6061 aluminum alloy composites reinforced rice husk ash particulates produced using compocasting

2017 ◽  
Vol 5 (2) ◽  
pp. 127-135 ◽  
Author(s):  
J. Allwyn Kingsly Gladston ◽  
I. Dinaharan ◽  
N. Mohamed Sheriff ◽  
J. David Raja Selvam
Keyword(s):  
Aluminum Alloy ◽  
Rice Husk ◽  
Sliding Wear ◽  
Rice Husk Ash ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding

Effect of Repeated Quenching Heat Treatment on Microstructure and Dry Sliding Wear Behavior of Low Carbon PM Steel

2007 ◽  
Vol 534-536 ◽  
pp. 673-676 ◽  
Author(s):  
Ahmet Güral ◽  
Süleyman Tekeli ◽  
Dursun Özyürek ◽  
Metin Gürü
Keyword(s):  
Heat Treatment ◽  
Sliding Wear ◽  
Volume Fraction ◽  
Wear Behavior ◽  
Constant Load ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Low Carbon ◽  
Ar Gas ◽  
Pin On Disk

The effect of repeated quenching heat treatment on microstructure and dry sliding wear behavior of low carbon PM steel was investigated. For this purpose, atomized iron powder was mixed with 0.3 % graphite and 1 % Ni powders. The mixed powders were cold pressed and sintered at 1200°C for 30 min under pure Ar gas atmosphere. Some of the sintered specimens were intercritically annealed at 760°C and quenched in water (single quenching). The other sintered specimens were first fully austenized at 890°C and water quenched. These specimens were then intercritically annealed at 760°C and re-quenched in water. The martensite volume fraction in the double quenched specimens was higher than that of the single quenched specimen. Wear tests were carried out on the single and double quenched specimens under dry sliding wear condition using a pin-on-disk type machine at constant load and speed. The experimental results showed that the wear coefficient effectively decreased in the double quenched specimen.

scholarly journals Studying The Effect of Reinforcing by Sicp on The Dry Sliding Wear Behavior and Mechanical Properties of AL- 4% CU Matrix Alloy

2013 ◽  
Vol 6 (2) ◽  
pp. 139-153
Author(s):  
Israa .A.K
Keyword(s):  
Mechanical Properties ◽  
Wear Rate ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Base Material ◽  
Weight Percent ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Cu Alloy

This research is devoted to study the effect of addition of different weight percent from SiCp ( 2, 4, 6, 8 ) to Al– 4 Cu alloy which have been fabricated by liquid metallurgy method on the dry sliding wear behavior and mechanical properties. Wear characteristics of Al–SiC composites have been investigated under dry sliding conditions and compared with base alloy. Dry sliding wear tests have been carried out using pin-on-disk wear test under normal applied loads 5, 10, 15 and 20 N and at different sliding velocity of (2.7, 3.7, 4.7) m/sec. It was also observed that the wear rate varies linearly with increases normal applied load but lower in composites as compared to the base material. The wear mechanism appears to be oxidative for both Al – Cu alloy and composites under the given conditions of load and sliding velocity as indicated by optical microscopic of the worn surfaces. Further, it was found from the experimentation that the wear rate decreases linearly with increasing weight percent of silicon carbide. The best results have been obtained at 8 % wt SiC . We also observed that the yield strength, tensile strength increases with increasing wt% of SiC , but the ductility decreases.

Sign in / Sign up

Export Citation Format

Share Document