End condition effect on distortional buckling of cold-formed steel columns with arbitrary length

2017 ◽  
Vol 117 ◽  
pp. 282-293 ◽  
Author(s):  
Tianhua Zhou ◽  
Yan Lu ◽  
Wenchao Li ◽  
Hanheng Wu
Keyword(s):  
Distortional Buckling ◽  
Arbitrary Length ◽  
Steel Columns ◽  
Condition Effect ◽  
Cold Formed Steel

scholarly journals Experiment and Design Method on Cold-Formed Thin-Walled Steel Lipped Channel Columns with Slotted Web Holes Under Axial Compression

2017 ◽  
Vol 11 (1) ◽  
pp. 244-257 ◽  
Author(s):  
Xingyou Yao
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Ultimate Strength ◽  
Test Results ◽  
Distortional Buckling ◽  
Steel Columns ◽  
Cold Formed Steel ◽  
Thin Walled ◽  
Shell Finite Element ◽  
The Web

Background: Cold-formed steel structural sections used in the walls of residential buildings and agricultural facilities are commonly C-shaped sections with web holes. These holes located in the web of sections can alter the elastic stiffness and the ultimate strength of a structural member. The objective of this paper is to study the buckling mode and load-carrying capacity of cold-formed thin-walled steel column with slotted web holes. Methods: Compression tests were conducted on 26 intermediate length columns with and without holes. The tested compressive members included four different kinds of holes. For each specimen, a shell finite element Eigen-buckling analysis and nonlinear analysis were also conducted. The influence of the slotted web hole on local and distortional buckling response had also been studied. The comparison on ultimate strength between test results and calculated results using Chinese cold-formed steel specification GB50018-2002, North American cold-formed steel specification AISI S100-2016, and nonlinear Finite Element method was made. Result: Test results showed that the distortional buckling occurred for intermediate columns with slotted holes and the ultimate strength of columns with holes was less than that of columns without holes. The ultimate strength of columns decreased with the increase in transverse width of hole in the cross-section of member. The Finite element analysis results showed that the web holes could influence on the elastic buckling stress of columns. The shell finite element could be used to model the buckling modes and analysis the ultimate strength of members with slotted web holes. The calculated ultimate strength shows that results predicted with AISI S100-2016 and analyzed using finite element method are close to test results. The calculated results using Chinese code are higher than the test results because Chinese code has no provision to calculate the ultimate strength of members with slotted web holes. Conclusion: The calculated method for cold-formed thin-walled steel columns with slotted web holes are proposed based on effective width method in Chinese code. The results calculated using the proposed method show good agreement with test results and can be used in engineering design for some specific cold-formed steel columns with slotted web holes studied in this paper.

Lipped channel cold-formed steel columns under local-distortional buckling mode interaction

2019 ◽  
Vol 137 ◽  
pp. 251-270 ◽  
Author(s):  
Gustavo Y. Matsubara ◽  
Eduardo de M. Batista ◽  
Guilherme C. Salles
Keyword(s):  
Mode Interaction ◽  
Distortional Buckling ◽  
Buckling Mode ◽  
Steel Columns ◽  
Cold Formed Steel

scholarly journals Behaviour of Cold Formed Built - Up Steel Compression Member

2019 ◽  
Vol 8 (4) ◽  
pp. 8409-8413
Keyword(s):  
Slenderness Ratio ◽  
Distortional Buckling ◽  
Cross Sectional ◽  
Buckling Modes ◽  
Steel Columns ◽  
Steel Members ◽  
Load Carrying ◽  
Cold Formed Steel ◽  
Ultimate Load Carrying Capacity ◽  
Sectional Shape

The use of cold-formed thin-walled steel structural members has increased in recent years. Especially, Cold-formed steel columns are widely used in the construction industry due to their lightweight, easy installation, erection and economy. The strength and efficiency of cold-formed steel profiles depends on the cross-sectional shape, which controls the three fundamental buckling modes: local, distortional and global. As most of their sections are open with only one symmetrical axis, they would likely fail by twisting and interacted with the other buckling modes such as local and distortional buckling. In order to improve the ultimate strength of columns, a built-up column section with distinct shape was selected from the detailed study of Literatures and three specimens of thickness 1.6mm were fabricated with different lengths 500mm, 600mm and 700mm. Consequently, buckling behaviour of built up steel members was investigated theoretically with Direct Strength Method (with the help of CuFSM) as well as experimentally and the results were compared with the buckling modes obtained numerically using ANSYS software and it is found that the ultimate load carrying capacity of the column increases with the decrease of slenderness ratio and finally a new innovative and economical column element was presented.

A Study on the Behaviour of Cold Formed Built - Up Steel Compression Member

2019 ◽  
Vol 1 (6) ◽  
pp. 225-234
Author(s):  
Thiyagu K ◽  
Elanchezhiyan R ◽  
Kanaka P ◽  
Ganamanikarnika N
Keyword(s):  
Slenderness Ratio ◽  
Distortional Buckling ◽  
Cross Sectional ◽  
Buckling Modes ◽  
Steel Columns ◽  
Steel Members ◽  
Load Carrying ◽  
Cold Formed Steel ◽  
Ultimate Load Carrying Capacity ◽  
Sectional Shape

The use of cold-formed thin-walled steel structural members has increased in recent years. Especially, Cold-formed steel columns are widely used in the construction industry due to their lightweight, easy installation, erection and economy. The strength and efficiency of cold-formed steel profiles depends on the cross-sectional shape, which controls the three fundamental buckling modes: local, distortional and global. As most of their sections are open with only one symmetrical axis, they would likely fail by twisting and interacted with the other buckling modes such as local and distortional buckling. In order to improve the ultimate strength of columns, a built-up column section with distinct shape was selected from the detailed study of Literatures and three specimens of thickness 1.6mm were fabricated with different lengths 500mm, 600mm and 700mm. Consequently, buckling behaviour of built up steel members was investigated theoretically with Direct Strength Method (with the help of CuFSM) as well as experimentally and the results were compared with the buckling modes obtained numerically using ANSYS software and it is found that the ultimate load carrying capacity of the column increases with the decrease of slenderness ratio and finally a new innovative and economical column element was presented.

Local–Distortional Interaction in Cold-formed Steel Columns: Mechanics, Testing, Numerical Simulation and Design

Structures ◽  
2015 ◽  
Vol 4 ◽  
pp. 38-57 ◽  
Author(s):  
André Dias Martins ◽  
Dinar Camotim ◽  
Pedro Borges Dinis ◽  
Ben Young
Keyword(s):  
Numerical Simulation ◽  
Steel Columns ◽  
Cold Formed Steel

Experimental Study on Mechanical Behavior of Cold-Formed Steel Three Limbs Built-up Section Members

2010 ◽  
Vol 163-167 ◽  
pp. 651-654
Author(s):  
Tian Hua Zhou ◽  
Shao Feng Nie ◽  
Xiang Bin Liu ◽  
Guang Yi Li
Keyword(s):  
Experimental Study ◽  
Mechanical Behavior ◽  
Axial Compression ◽  
Local Buckling ◽  
Distortional Buckling ◽  
Torsional Buckling ◽  
Failure Characteristics ◽  
Compression Load ◽  
Cold Formed Steel ◽  
Flexural Torsional Buckling

18 specimens of cold-formed steel three limbs built-up section members are tested under axial compression load in this paper. The section forms are divided into two categories: A and B. Load-displacement (P-Δ) curves and failure characteristics of specimens are obtained. The results show that: As to section A members, the failure characteristics of LC, MC and SC series of specimens are flexural-torsional buckling, torsional buckling and distortional buckling, local buckling and distortional buckling. As to section B members, the failure characteristics of LC, MC series of specimens are flexural buckling, while local buckling and distortional buckling for members of SC series.

Sign in / Sign up

Export Citation Format

Share Document