Effect of refining time and calcium addition on the removal of oxygen, nitrogen, and hydrogen from IN713LC superalloy during vacuum induction refining

Vacuum ◽  
2021 ◽  
pp. 110752
Author(s):  
Farzad Behboudi Khiavi ◽  
Mansour Soltanieh ◽  
Seyed Mehdi Abbasi
2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Amit Kumar ◽  
Chhotu Ram ◽  
Adebabay Tazeb

AbstractEnergy conservation has become an essential step in pulp and paper industry due to diminishing fossil reserves and high cost of energy. Refining is a mechanical treatment of pulp that modifies the structure of the fibres in order to achieve desired paper-making properties. However, it consumes considerable amount of energy. The electrical power consumption has a direct impact on paper manufacturing cost. Therefore, there is a requirement to minimize the energy cost. Enzyme-assisted refining is the environment friendly option that reduces the energy consumption for papermaking. Enzyme-assisted refining is defined as mechanical refining after pretreatment of pulp with enzymes such as cellulases and hemicellulases. It not only reduces the energy consumption but also improves the quality of finished paper. Enzymes improve the beatability of pulp at same refining degree (°SR) and desired paper properties can be achieved at decreased refining time. The selection of suitable enzyme, optimization of enzyme dose and appropriate reaction time are the key factors for energy reduction and pulp quality improvement during enzyme-assisted refining.


Foods ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 1368
Author(s):  
Marbie Alpos ◽  
Sze Ying Leong ◽  
Indrawati Oey

Legumes are typically soaked overnight to reduce antinutrients and then cooked prior to consumption. However, thermal processing can cause over-softening of legumes. This study aimed to determine the effect of calcium addition (0, 100, 300, and 500 ppm in the form of calcium chloride, CaCl2), starting from the overnight soaking step, in reducing the loss of firmness of black beans during thermal processing for up to 2 h. The impact of calcium addition on the in vitro starch and protein digestibility of cooked beans was also assessed. Two strategies of calcium addition were employed in this study: (Strategy 1/S1) beans were soaked and then cooked in the same CaCl2 solution, or (Strategy 2/S2) cooked in a freshly prepared CaCl2 solution after the calcium-containing soaking medium was discarded. Despite the texture degradation of black beans brought about by increasing the cooking time, texture profile analysis (TPA) revealed that their hardness, cohesiveness, springiness, chewiness, and resilience improved significantly (p < 0.05) with increasing calcium concentration. Interestingly, beans cooked for 2 h with 300 ppm CaCl2 shared similar hardness with beans cooked for 1 h without calcium addition. Starch and protein digestibility of calcium-treated beans generally improved with prolonged cooking. However, calcium-treated beans cooked for 1 h under S2 achieved a reduced texture loss and a lower starch digestibility than those beans treated in S1. A lower starch digestion could be desired as this reflects a slow rise in blood glucose levels. Findings from this result also showed that treating black beans with high level of CaCl2 (i.e., 500 ppm) was not necessary, otherwise this would limit protein digestibility of cooked black beans.


2010 ◽  
Vol 156-157 ◽  
pp. 882-885 ◽  
Author(s):  
Yu Yan Hu ◽  
Dong Liang Lu ◽  
Tao Lin ◽  
Yu Liu ◽  
Bo Wang ◽  
...  

Refining of solar grade silicon by metallurgical method is the research hotspot of polycrystalline field. Slagging method is benefit to the removal of the impurities especially to boron exsisted in the raw silicon. In this study, the influence of the density, the viscosity and liquidus temperature of the slag components on the refining process were discussed, and then the slag system SiO2-Na2CO3 was choosed as the slagging agents. And then the impact factors on the removal efficiency of boron such as the composition of SiO2 and Na2CO3, the ratio of slag to silicon and the refining time were investigated by the orthogonal experiment. The results showed that the optimum parameters of the oxidation refining for removing boron were as follows: the main composition of the oxidant is “SiO2 : Na2CO3 = 60% : 40%”; the slag/silicon ratio is 0.5; time for refining is 60min at 1550 . The results indicated that the removal efficiency of boron was 88.28%, and the content of boron in MG-Si can be reduced to 7ppmw under the best refining process¬.


2021 ◽  
Author(s):  
Nataliya N. Klimenko ◽  
Kristina I. Kiseleva ◽  
Karina I. Kienskaya ◽  
Alexey V. Nistratov ◽  
Leonid M. Delitsyn

1987 ◽  
Vol 37 (1) ◽  
pp. 42-47 ◽  
Author(s):  
Hidetoshi UENO ◽  
Shigeru AKIYAMA

2018 ◽  
Vol 309 ◽  
pp. 2-10 ◽  
Author(s):  
Fangzhu Jin ◽  
Hongman Sun ◽  
Chunfei Wu ◽  
Huajuan Ling ◽  
Yijiao Jiang ◽  
...  

2021 ◽  
Vol 1033 ◽  
pp. 69-73
Author(s):  
Jing Wen Zhu ◽  
Jing Tao Zhao ◽  
Zong Ming Jiang ◽  
Ying Long Li

The application of ultrasonic field in the preparation of Al-Ti-C refiners can lead to the the homogenous distribution of the second phase TiAl3 and the particle phase TiC in the matrix, thus enhancing the refinement effect. In this paper, the Al-Ti-C grain refiner was successfully prepared by the ultrasonic coupling method, and its microstructure was observed. The prepared refiner was added to pure Al to verify the refining performance, and the refining mechanism was analyzed. The results indicate that the Al-Ti-C grain refiner prepared by ultrasonic field has excellent refining performance, which reduces the grain size of Al to 100 μm, and the optimum activation refining time is 3 min. The reason is that the morphology and size of the second phase TiAl3 and TiC in Al-Ti-C are changed by cavitation effect, acoustic streaming effect and thermal effect caused by high intensity ultrasonic, and the α-Al nucleates effectively under the synergistic of TiC and TiAl3 particles.


Sign in / Sign up

Export Citation Format

Share Document