Microstructure and Properties of Electron Beam Welded Tantalum-to-Stainless Steel Joints

2013 ◽  
Vol 42 (5) ◽  
pp. 914-918 ◽  
Author(s):  
Chen Guoqing ◽  
Zhang Binggang ◽  
Zhuang Yuan ◽  
Deng Binghui ◽  
Feng Jicai
Keyword(s):  
Stainless Steel ◽  
Electron Beam ◽  
Microstructure And Properties ◽  
Steel Joints

scholarly journals Correction: Liu et al. Microstructure and Properties of SUS304 Stainless Steel Joints Brazed with Electrodeposited Ni-Cr-P Alloy Coatings. Materials 2021, 14, 4216

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5499
Author(s):  
Shubin Liu ◽  
Ikuo Shohji ◽  
Tatsuya Kobayashi ◽  
Katsuharu Osanai ◽  
Tetsuya Ando ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Microstructure And Properties ◽  
Sus304 Stainless Steel ◽  
Steel Joints

Error in Figure/Table [...]

Microstructure and Properties of 6061 Aluminum Alloy Superficially Modified by Electron Beam Alloying with 1Cr13 Stainless Steel

2013 ◽  
Vol 470 ◽  
pp. 48-52
Author(s):  
Rong Wang ◽  
Ming Sheng Li ◽  
De Qiang Wei
Keyword(s):  
Stainless Steel ◽  
Electron Beam ◽  
High Speed ◽  
Friction And Wear ◽  
X Ray Diffraction ◽  
Microstructure And Properties ◽  
Hardness Tester ◽  
Fine Grain ◽  
Metallurgical Bonding ◽  
Modified Layer

1Cr13 stainless steel was pre-coated on the surface of 6061 aluminum for electron beam alloying, then the microstructure and properties of the modified layer was discussed and analyzed. Using Scanning electron microscopy (SEM), EDAX energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and other analytical testing methods to analyze the microstructure and phase composition of the modified layer; Using the HX-1000TM automatic turret micro-hardness tester and HSR-2M high-speed reciprocating friction and wear tester to respectively measure its hardness and wear, finally to analyze the modification effect. The results showed that: between the alloyed layer and the substrate obtains a good metallurgical bonding; the modified layer organization composes mainly of martensite and Al-Fe compounds, and has fine grain; the hardness of the strengthening layer is about 4 times that of the substrate, and its wear resistance is a quarter of the matrixs.

scholarly journals Texture mapping in electron beam welded dissimilar copper-stainless steel joints by neutron diffraction

Vacuum ◽  
2020 ◽  
Vol 181 ◽  
pp. 109668
Author(s):  
Soumitra Kumar Dinda ◽  
Jyotirmaya Kar ◽  
Gour Gopal Roy ◽  
Winfried Kockelmann ◽  
Prakash Srirangam
Keyword(s):  
Stainless Steel ◽  
Electron Beam ◽  
Neutron Diffraction ◽  
Texture Mapping ◽  
Steel Joints

Influence of heat input in electron beam process on microstructure and properties of duplex stainless steel welded interface

2018 ◽  
Vol 435 ◽  
pp. 352-366 ◽  
Author(s):  
Zhiqiang Zhang ◽  
Hongyang Jing ◽  
Lianyong Xu ◽  
Yongdian Han ◽  
Lei Zhao ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Electron Beam ◽  
Duplex Stainless Steel ◽  
Heat Input ◽  
Microstructure And Properties

Metallurgical investigation of electron beam welded duplex stainless steel X2CrNiMoN22-5-3 with plasma nitrided weld edge surfaces

2018 ◽  
Vol 60 (6) ◽  
pp. 577-582
Author(s):  
Sergii Krasnorutskyi ◽  
Christian Kipp ◽  
Jonas Hensel ◽  
Peter Kaestner ◽  
Sven Hartwig ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Electron Beam ◽  
Duplex Stainless Steel ◽  
Metallurgical Investigation ◽  
Weld Edge
Sign in / Sign up

Export Citation Format

Share Document