scholarly journals Quasi-steady linked vortices with chaotic streamlines

2011 ◽  
Vol 687 ◽  
pp. 571-583 ◽  
Author(s):  
Oscar Velasco Fuentes ◽  
Angélica Romero Arteaga

AbstractThis paper describes the motion and the flow geometry of two or more linked ring vortices in an otherwise quiescent, ideal fluid. The vortices are thin tubes of near-circular shape which lie on the surface of an immaterial torus of small aspect ratio. Since the vortices are assumed to be identical and evenly distributed on any meridional section of the torus, the flow evolution depends only on the number of vortices ($n$) and the torus aspect ratio (${r}_{1} / {r}_{0} $, where ${r}_{0} $ is the centreline radius and ${r}_{1} $ is the cross-section radius). Numerical simulations based on the Biot–Savart law showed that a small number of vortices ($n= 2, 3$) coiled on a thin torus (${r}_{1} / {r}_{0} \leq 0. 16$) progressed along and rotated around the symmetry axis of the torus in an almost uniform manner while each vortex approximately preserved its shape. In the comoving frame the velocity field always possesses two stagnation points. The transverse intersection, along $2n$ streamlines, of the stream tube emanating from the front stagnation point and the stream tube ending at the rear stagnation point creates a three-dimensional chaotic tangle. It was found that the volume of the chaotic region increases with increasing torus aspect ratio and decreasing number of vortices.

1994 ◽  
Vol 116 (3) ◽  
pp. 331-336 ◽  
Author(s):  
Ding-Yu Fei ◽  
James D. Thomas ◽  
Stanley E. Rittgers

Flow in distal end-to-side anastomoses of iliofemoral artery bypass grafts was simulated using a steady flow, three-dimensional numerical model. With the proximal artery occluded, anastomotic angles were varied over 20, 30, 40, 45, 50, 60 and 70 deg while the inlet Reynolds numbers were 100 and 205. Fully developed flow in the graft became somewhat skewed toward the inner wall with increasing angle for both Reynolds numbers. Separated flow regions were seen along the inner arterial wall (toe region) for angles ≥ 60 deg at Re = 100 and for angles ≥ 45 deg at Re = 205 while a stagnation point existed along the outer arterial wall (floor region) for all cases which moved downstream relative to the toe of the anastomosis with decreasing angles. Normalized shear rates (NSR) along the arterial wall varied widely throughout the anastomotic region with negative values seen in the separation zones and upstream of the stagnation points which increased in magnitude with angle. The NSR increased with distance downstream of the stagnation point and with magnitudes which increased with the angle. Compared with observations from chronic in vivo studies, these results appear to support the hypothesis of greater intimal hyperplasia occurring in regions of low fluid shear.


Author(s):  
Jae-Young Lee ◽  
Sa-Ya Lee

The nuclear core of High Temperature Gas Reactor (HTGR) with pebble bed type has been investigated intensively due to its benefits in management, but its complicated flow geometry requested the reliable analytical method. Recent studies have been made using the three dimensional computational methods but they need to be evaluated with the experimental data. Due to the complicated and narrow flow channel, the intrusive methods of flow measurement are not proper in the study. In the present study, we developed a wind tunnel for the pebble bed geometry in the structure of Face Centered Cubic (FCC) and measure the flow field using the Particle Image Velocimetry (PIV) directly. Due to the limitation of the image harnessing speed and accessibility of the light for particle identification, the system is scaled up to reduce the mean flow velocity by keeping the same Reynolds number of the HTGR. The velocity fields are successfully determined to identify the stagnation points suspected to produce hot spots on the surface of the pebble. It is expected that the present data is useful to evaluate the three dimensional Computational Fluid Dynamics (CFD) analysis. Furthermore, It would provide an insight of experimental method if the present results are compared by those of scaled down and liquid medium.


1975 ◽  
Vol 67 (2) ◽  
pp. 289-297 ◽  
Author(s):  
J. A. Howarth

The theory of boundary-layer growth at a rear stagnation point, first presented by Proudman & Johnson, is here extended to cover fully three-dimensional rear stagnation points. Supporting numerical solutions of the full initial-value problem establish the relevance of the in viscid similarity solutions obtained.


2010 ◽  
Author(s):  
Vai Kuong Sin ◽  
Tai Yin Tong ◽  
Theodore E. Simos ◽  
George Psihoyios ◽  
Ch. Tsitouras

Nanoscale ◽  
2017 ◽  
Vol 9 (46) ◽  
pp. 18311-18317 ◽  
Author(s):  
Yuan Gao ◽  
Yuanjing Lin ◽  
Zehua Peng ◽  
Qingfeng Zhou ◽  
Zhiyong Fan

Three-dimensional interconnected nanoporous structure (3-D INPOS) possesses high aspect ratio, large surface area, as well as good structural stability. Profiting from its unique interconnected architecture, the 3-D INPOS pseudocapacitor achieves a largely enhanced capacitance and rate capability.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Mana Iwai ◽  
Tatsuya Kikuchi ◽  
Ryosuke O. Suzuki

AbstractHigh-aspect ratio ordered nanomaterial arrays exhibit several unique physicochemical and optical properties. Porous anodic aluminum oxide (AAO) is one of the most typical ordered porous structures and can be easily fabricated by applying an electrochemical anodizing process to Al. However, the dimensional and structural controllability of conventional porous AAOs is limited to a narrow range because there are only a few electrolytes that work in this process. Here, we provide a novel anodizing method using an alkaline electrolyte, sodium tetraborate (Na2B4O7), for the fabrication of a high-aspect ratio, self-ordered nanospike porous AAO structure. This self-ordered porous AAO structure possesses a wide range of the interpore distance under a new anodizing regime, and highly ordered porous AAO structures can be fabricated using pre-nanotexturing of Al. The vertical pore walls of porous AAOs have unique nanospikes measuring several tens of nanometers in periodicity, and we demonstrate that AAO can be used as a template for the fabrication of nanomaterials with a large surface area. We also reveal that stable anodizing without the occurrence of oxide burning and the subsequent formation of uniform self-ordered AAO structures can be achieved on complicated three-dimensional substrates.


1991 ◽  
Vol 35 (04) ◽  
pp. 314-324
Author(s):  
Todd McComb

Using low-aspect-ratio flat ship theory, this paper defines a procedure to determine the position of a hull which is in equilibrium at some "fast" speed in terms of a given hull shape for the same hull at rest. This procedure is then used to find the equilibrium flow past a moving ship, when given the shape of the hull at rest. The method is then extended to find the hull configuration at various speeds based on either the configuration in the static case or at some other equilibrium speed, leading to a calculation of drag versus speed. Some general formulas and some simple examples are given.


2021 ◽  
Vol 10 (9) ◽  
pp. 3273-3282
Author(s):  
M.E.H. Hafidzuddin ◽  
R. Nazar ◽  
N.M. Arifin ◽  
I. Pop

The problem of steady laminar three-dimensional stagnation-point flow on a permeable stretching/shrinking sheet with second order slip flow model is studied numerically. Similarity transformation has been used to reduce the governing system of nonlinear partial differential equations into the system of ordinary (similarity) differential equations. The transformed equations are then solved numerically using the \texttt{bvp4c} function in MATLAB. Multiple solutions are found for a certain range of the governing parameters. The effects of the governing parameters on the skin friction coefficients and the velocity profiles are presented and discussed. It is found that the second order slip flow model is necessary to predict the flow characteristics accurately.


Sign in / Sign up

Export Citation Format

Share Document