Numerical simulations of lock-exchange compositional gravity current

2009 ◽  
Vol 635 ◽  
pp. 361-388 ◽  
Author(s):  
SENG KEAT OOI ◽  
GEORGE CONSTANTINESCU ◽  
LARRY WEBER

Compositional gravity current flows produced by the instantaneous release of a finite-volume, heavier lock fluid in a rectangular horizontal plane channel are investigated using large eddy simulation. The first part of the paper focuses on the evolution of Boussinesq lock-exchange gravity currents with a large initial volume of the release during the slumping phase in which the front of the gravity current propagates with constant speed. High-resolution simulations are conducted for Grashof numbers $\sqrt {Gr}$ = 3150 (LGR simulation) and $\sqrt {Gr}$ = 126000 (HGR simulation). The Grashof number is defined with the channel depth h and the buoyancy velocity ub = $\sqrt {g'h}$ (g′ is the reduced gravity). In the HGR simulation the flow is turbulent in the regions behind the two fronts. Compared to the LGR simulation, the interfacial billows lose their coherence much more rapidly (over less than 2.5h behind the front), which results in a much faster decay of the large-scale content and turbulence intensity in the trailing regions of the flow. A slightly tilted, stably stratified interface layer develops away from the two fronts. The concentration profiles across this layer can be approximated by a hyperbolic tangent function. In the HGR simulation the energy budget shows that for t > 18h/ub the flow reaches a regime in which the total dissipation rate and the rates of change of the total potential and kinetic energies are constant in time. The second part of the paper focuses on the study of the transition of Boussinesq gravity currents with a small initial volume of the release to the buoyancy–inertia self-similar phase. When the existence of the back wall is communicated to the front, the front speed starts to decrease, and the current transitions to the buoyancy–inertia phase. Three high-resolution simulations are performed at Grashof numbers between $\sqrt {Gr}$ = 3 × 104 and $\sqrt {Gr}$ = 9 × 104. Additionally, a calculation at a much higher Grashof number ($\sqrt {Gr}$ = 106) is performed to understand the behaviour of a bottom-propagating current closer to the inviscid limit. The three-dimensional simulations correctly predict a front speed decrease proportional to t−α (the time t is measured from the release time) over the buoyancy–inertia phase, with the constant α approaching the theoretical value of 1/3 as the current approaches the inviscid limit. At Grashof numbers for which $\sqrt {Gr}$ > 3 × 104, the intensity of the turbulence in the near-wall region behind the front is large enough to induce the formation of a region containing streaks of low and high streamwise velocities. The streaks are present well into the buoyancy–inertia phase before the speed of the front decays below values at which the streaks can be sustained. The formation of the velocity streaks induces a streaky distribution of the bed friction velocity in the region immediately behind the front. This distribution becomes finer as the Grashof number increases. For simulations in which the only difference was the value of the Grashof number ($\sqrt {Gr}$ = 4.7 × 104 versus $\sqrt {Gr}$ = 106), analysis of the non-dimensional bed friction velocity distributions shows that the capacity of the gravity current to entrain sediment from the bed increases with the Grashof number. Past the later stages of the transition to the buoyancy–inertia phase, the temporal variations of the potential energy, the kinetic energy and the integral of the total dissipation rate are logarithmic.

2008 ◽  
Vol 616 ◽  
pp. 327-356 ◽  
Author(s):  
BRIAN L. WHITE ◽  
KARL R. HELFRICH

A steady theory is presented for gravity currents propagating with constant speed into a stratified fluid with a general density profile. Solution curves for front speed versus height have an energy-conserving upper bound (the conjugate state) and a lower bound marked by the onset of upstream influence. The conjugate state is the largest-amplitude nonlinear internal wave supported by the ambient stratification, and in the limit of weak stratification approaches Benjamin's energy-conserving gravity current solution. When the front speed becomes critical with respect to linear long waves generated above the current, steady solutions cannot be calculated, implying upstream influence. For non-uniform stratification, the critical long-wave speed exceeds the ambient long-wave speed, and the critical-Froude-number condition appropriate for uniform stratification must be generalized. The theoretical results demonstrate a clear connection between internal waves and gravity currents. The steady theory is also compared with non-hydrostatic numerical solutions of the full lock release initial-value problem. Some solutions resemble classic gravity currents with no upstream disturbance, but others show long internal waves propagating ahead of the gravity current. Wave generation generally occurs when the stratification and current speed are such that the steady gravity current theory fails. Thus the steady theory is consistent with the occurrence of either wave-generating or steady gravity solutions to the dam-break problem. When the available potential energy of the dam is large enough, the numerical simulations approach the energy-conserving conjugate state. Existing laboratory experiments for intrusions and gravity currents produced by full-depth lock exchange flows over a range of stratification profiles show excellent agreement with the conjugate state solutions.


2012 ◽  
Vol 694 ◽  
pp. 252-291 ◽  
Author(s):  
Talia Tokyay ◽  
George Constantinescu ◽  
Eckart Meiburg

AbstractThe bed friction velocity distribution and sediment entrainment potential of Boussinesq compositional gravity currents propagating over a series of obstacles and over a smooth surface, respectively, are analysed based on high-resolution, three-dimensional large-eddy simulations. The investigation focuses on the parameter regime for which currents with a high volume of release go through an extended slumping phase with approximately constant front velocity (Tokyay, Constantinescu & Meiburg, J. Fluid Mech., vol. 672, 2011, 570–605). Under these conditions, a quasi-steady regime is reached between consecutive obstacles that is similar to the steady regime observed for constant-density channel flows over bottom obstacles. At a given location, this quasi-steady regime is reached in the tail of the current after the passage of the front and the associated hydraulic jumps reflected from the first few downstream obstacles. A double-averaging procedure is employed to characterize the global changes in the structure of the tail region between currents with a high volume of release propagating over smooth surfaces and over obstacles. Reynolds-number-induced scale effects on the flow and turbulence structure within the tail region are discussed in some detail. The presence of this quasi-steady regime is significant, since the simulations with obstacles show that most of the sediment is entrained by the tail of the current, rather than by its front. A detailed analysis of the effects of the obstacle shape on the quasi-steady mean flow and turbulence structure is presented, which provides insight into why gravity currents over dunes can entrain more sediment than gravity currents over ribs of comparable size. Finally, the bed friction velocity distributions and the potential to entrain sediment are compared for a compositional current with a high volume of release during the slumping phase, and a current with a low volume of release for which transition to the buoyancy–inertia phase occurs a short time after the release of the lock gate.


2007 ◽  
Vol 594 ◽  
pp. 369-377 ◽  
Author(s):  
DIOGO BOLSTER ◽  
ALICE HANG ◽  
P. F. LINDEN

This paper examines intrusive Boussinesq gravity currents, propagating into a continuously stratified fluid. We develop a model, based on energy arguments, to predict the front speed of such an intrusive gravity current from a lock release. We find that the depth at which the intrusion occurs, which corresponds to the level of neutral buoyancy (i.e. the depth where the intrusion density equals the stratified fluid density), affects the front speed. The maximum speeds occur when the intrusion travels along the top and bottom boundaries and the minimum speed occurs at mid-depth. Experiments and numerical simulations were conducted to compare to the theoretically predicted values, and good agreement was found.


2014 ◽  
Vol 762 ◽  
pp. 417-434 ◽  
Author(s):  
Catherine S. Jones ◽  
Claudia Cenedese ◽  
Eric P. Chassignet ◽  
P. F. Linden ◽  
Bruce R. Sutherland

AbstractThe advance of the front of a dense gravity current propagating in a rectangular channel and V-shaped valley both horizontally and up a shallow slope is examined through theory, full-depth lock–release laboratory experiments and hydrostatic numerical simulations. Consistent with theory, experiments and simulations show that the front speed is relatively faster in the valley than in the channel. The front speed measured shortly after release from the lock is 5–22 % smaller than theory, with greater discrepancy found in upsloping V-shaped valleys. By contrast, the simulated speed is approximately 6 % larger than theory, showing no dependence on slope for rise angles up to ${\it\theta}=8^{\circ }$. Unlike gravity currents in a channel, the current head is observed in experiments to be more turbulent when propagating in a V-shaped valley. The turbulence is presumably enhanced due to the lateral flows down the sloping sides of the valley. As a consequence, lateral momentum transport contributes to the observed lower initial speeds. A Wentzel–Kramers–Brillouin like theory predicting the deceleration of the current as it runs upslope agrees remarkably well with simulations and with most experiments, within errors.


Ocean Science ◽  
2013 ◽  
Vol 9 (6) ◽  
pp. 1003-1014 ◽  
Author(s):  
V. Paka ◽  
V. Zhurbas ◽  
B. Rudels ◽  
D. Quadfasel ◽  
A. Korzh ◽  
...  

Abstract. To examine processes controlling the entrainment of ambient water into the Denmark Strait overflow (DSO) plume/gravity current, measurements of turbulent dissipation rate were carried out by a quasi-free-falling (tethered) microstructure profiler (MSP). The MSP was specifically designed to collect data on dissipation-scale turbulence and fine thermohaline stratification in an ocean layer located as deep as 3500 m. The task was to perform microstructure measurements in the DSO plume in the lower 300 m depth interval including the bottom mixed layer and the interfacial layer below the non-turbulent ambient water. The MSP was attached to a Rosette water sampler rack equipped with a SeaBird CTDO and an RD Instruments lowered acoustic Doppler current profiler (LADCP). At a chosen depth, the MSP was remotely released from the rack to perform measurements in a quasi-free-falling mode. Using the measured vertical profiles of dissipation, the entrainment rate as well as the bottom and interfacial stresses in the DSO plume were estimated at a location 200 km downstream of the sill at depths up to 1771 m. Dissipation-derived estimates of entrainment were found to be much smaller than bulk estimates of entrainment calculated from the downstream change of the mean properties in the plume, suggesting the lateral stirring due to mesoscale eddies rather than diapycnal mixing as the main contributor to entrainment. Dissipation-derived bottom stress estimates are argued to be roughly one third the magnitude of those derived from log velocity profiles. In the interfacial layer, the Ozmidov scale calculated from turbulence dissipation rate and buoyancy frequency was found to be linearly proportional to the overturning scale extracted from conventional CTD data (the Thorpe scale), with a proportionality constant of 0.76, and a correlation coefficient of 0.77.


2018 ◽  
Vol 851 ◽  
pp. 507-544 ◽  
Author(s):  
Roberto Inghilesi ◽  
Claudia Adduce ◽  
Valentina Lombardi ◽  
Federico Roman ◽  
Vincenzo Armenio

Unconfined three-dimensional gravity currents generated by lock exchange using a small dividing gate in a sufficiently large tank are investigated by means of large eddy simulations under the Boussinesq approximation, with Grashof numbers varying over five orders of magnitudes. The study shows that, after an initial transient, the flow can be separated into an axisymmetric expansion and a globally translating motion. In particular, the circular frontline spreads like a constant-flow-rate, axially symmetric gravity current about a virtual source translating along the symmetry axis. The flow is characterised by the presence of lobe and cleft instabilities and hydrodynamic shocks. Depending on the Grashof number, the shocks can either be isolated or produced continuously. In the latter case a typical ring structure is visible in the density and velocity fields. The analysis of the frontal spreading of the axisymmetric part of the current indicates the presence of three regimes, namely, a slumping phase, an inertial–buoyancy equilibrium regime and a viscous–buoyancy equilibrium regime. The viscous–buoyancy phase is in good agreement with the model of Huppert (J. Fluid Mech., vol. 121, 1982, pp. 43–58), while the inertial phase is consistent with the experiments of Britter (Atmos. Environ., vol. 13, 1979, pp. 1241–1247), conducted for purely axially symmetric, constant inflow, gravity currents. The adoption of the slumping model of Huppert & Simpson (J. Fluid Mech., vol. 99 (04), 1980, pp. 785–799), which is here extended to the case of constant-flow-rate cylindrical currents, allows reconciling of the different theories about the initial radial spreading in the context of different asymptotic regimes. As expected, the slumping phase is governed by the Froude number at the lock’s gate, whereas the transition to the viscous phase depends on both the Froude number at the gate and the Grashof number. The identification of the inertial–buoyancy regime in the presence of hydrodynamic shocks for this class of flows is important, due to the lack of analytical solutions for the similarity problem in the framework of shallow water theory. This fact has considerably slowed the research on variable-flow-rate axisymmetric gravity currents, as opposed to the rapid development of the knowledge about cylindrical constant-volume and planar gravity currents, despite their own environmental relevance.


2000 ◽  
Author(s):  
Ryan J. Lowe

Abstract Laboratory experiments were performed in which an intrusive gravity current was observed using shadowgraph and particle tracking methods. The intrusion was generated in a two-layer fluid with a sharp interface by mixing the fluid behind a vertical lock-gate and then suddenly withdrawing the gate from the tank. The purpose of the experiments is to determine the structure of the velocity field inside the intrusion as well as the stability characteristics of the interface. Soon after the removal of the lock-gate the speed of the front of the intrusive gravity current reached a constant speed. The observed structure of the flow inside the intrusion shows a “head region” where the flow is nearly uniform, followed by a region of intense mixing and high velocities and finally followed by another region of fairly uniform velocity with a speed slightly faster than the front speed. The results show that the maximum centerline velocity is about 50% greater than the front speed and corresponds to the position in the intrusion where the strongest Kelvin- Helmholtz billows form. Closer to the front, the relative flow within the head is weak, which explains why Benjamin’s (1968) energy-conserving gravity current theory accurately predicts the behavior of dissipative gravity currents.


2019 ◽  
Vol 869 ◽  
pp. 610-633 ◽  
Author(s):  
L. Chiapponi ◽  
M. Ungarish ◽  
D. Petrolo ◽  
V. Di Federico ◽  
S. Longo

We present a combined theoretical and experimental study of lock-release inertial gravity currents (GCs) propagating in a horizontal channel of circular cross-section with open-top surface in the non-Boussinesq regime. A two-layer shallow-water (SW) model is developed for a generic shape of the cross-section with open top, and then implemented in a finite difference numerical code for the solution in a circular-cross-section channel of the type used in the experiments. The model predicts propagation with (almost) constant speed for a fairly long distance, accompanied by a depression of the ambient free open-top surface behind the front of the current. Sixteen experiments were conducted with a density ratio $r=0.587{-}0.939$ in full-depth and part-depth release conditions, measuring the front speed and the free-surface time series at four cross-sections. The channel was a circular tube 409 cm long, with a radius of 9.5 cm; the lengths of the locks were 52 and 103.5 cm. Density contrast was obtained by adding sodium chloride and dipotassium phosphate to fresh water. The theoretical values of the front speed and of the depression overestimate the experimental values, but they predict correctly their trend for varying parameters and provide reliable insights into the underlying mechanisms. In particular, we demonstrate that the circular cross-section increases the speed of propagation as compared to the standard rectangular cross-section case (for the same initial height and density ratio). The discrepancies between the SW predictions and the present experiments are of the same order of magnitude as those of previously published results for simpler systems (Boussinesq, rectangular). In addition to the depression, which is a wave bound to, and following the front of, the GC, the system also displays two kinds of free-surface waves, namely the initial bump (its amplitude is of the same order as the depression) and some short-length and low-amplitude waves in the tail of the bump. These free waves propagate with a celerity well predicted by the ‘fast’ eigenvalues of the mathematical model. Comparison is provided with the celerity of a solitary wave. It is expected that discrepancies between theory and experiments can be partly attributed to the presence of these waves. The reported insights and SW prediction method can be applied to a variety of cross-sections of practical interest (triangles, trapezoids, etc.).


1968 ◽  
Vol 31 (2) ◽  
pp. 209-248 ◽  
Author(s):  
T. Brooke Benjamin

This paper presents a broad investigation into the properties of steady gravity currents, in so far as they can be represented by perfect-fluid theory and simple extensions of it (like the classical theory of hydraulic jumps) that give a rudimentary account of dissipation. As usually understood, a gravity current consists of a wedge of heavy fluid (e.g. salt water, cold air) intruding into an expanse of lighter fluid (fresh water, warm air); but it is pointed out in § 1 that, if the effects of viscosity and mixing of the fluids at the interface are ignored, the hydrodynamical problem is formally the same as that for an empty cavity advancing along the upper boundary of a liquid. Being simplest in detail, the latter problem is treated as a prototype for the class of physical problems under study: most of the analysis is related to it specifically, but the results thus obtained are immediately applicable to gravity currents by scaling the gravitational constant according to a simple rule.In § 2 the possible states of steady flow in the present category between fixed horizontal boundaries are examined on the assumption that the interface becomes horizontal far downstream. A certain range of flows appears to be possible when energy is dissipated; but in the absence of dissipation only one flow is possible, in which the asymptotic level of the interface is midway between the plane boundaries. The corresponding flow in a tube of circular cross-section is found in § 3, and the theory is shown to be in excellent agreement with the results of recent experiments by Zukoski. A discussion of the effects of surface tension is included in § 3. The two-dimensional energy-conserving flow is investigated further in § 4, and finally a close approximation to the shape of the interface is obtained. In § 5 the discussion turns to the question whether flows characterized by periodic wavetrains are realizable, and it appears that none is possible without a large loss of energy occurring. In § 6 the case of infinite total depth is considered, relating to deeply submerged gravity currents. It is shown that the flow must always feature a breaking ‘head wave’, and various properties of the resulting wake are demonstrated. Reasonable agreement is established with experimental results obtained by Keulegan and others.


2010 ◽  
Vol 40 (8) ◽  
pp. 1819-1834 ◽  
Author(s):  
Lars Umlauf ◽  
Lars Arneborg ◽  
Richard Hofmeister ◽  
Hans Burchard

Abstract The physics of shallow gravity currents passing through a rotating channel at subcritical Froude number is investigated here with a series of idealized numerical experiments. It is found that the combined effects of friction and rotation set up a complex transverse circulation that has some crucial implications for the entrainment process. A key component of this secondary circulation is a geostrophically balanced transverse jet in the interface that laterally drains fluid from the interface. This effect is shown to result in a strong cross-channel asymmetry and a spatial separation of the entrainment process: drained interfacial fluid is partly replaced by entrained ambient fluid on the deep side of the gravity current, whereas the downward mixing of buoyant fluid occurs on the shallow side. These results, closely corresponding to recent measurements in a shallow, channelized gravity current in the western Baltic Sea, illustrate that the description of entrainment as a strictly vertical mixing process with the help of local bulk parameters like the Froude number is not generally applicable in rotating gravity currents.


Sign in / Sign up

Export Citation Format

Share Document