Dynamic modeling and power optimization of a 4RPSP+PS parallel flight simulator machine

Robotica ◽  
2021 ◽  
pp. 1-26
Author(s):  
Soheil Zarkandi
Keyword(s):  
Power Consumption ◽  
Dynamic Modeling ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Pareto Front ◽  
Essential Role ◽  
Power Optimization ◽  
Optimal Designs ◽  
Flight Simulator ◽  
Lagrange Method

Abstract Reducing consumed power of a robotic machine has an essential role in enhancing its energy efficiency and must be considered during its design process. This paper deals with dynamic modeling and power optimization of a four-degrees-of-freedom flight simulator machine. Simulator cabin of the machine has yaw, pitch, roll and heave motions produced by a 4RPSP+PS parallel manipulator (PM). Using the Euler–Lagrange method, a closed-form dynamic equation is derived for the 4RPSP+PS PM, and its power consumption is computed on the entire workspace. Then, a newly introduced optimization algorithm called multiobjective golden eagle optimizer is utilized to establish a Pareto front of optimal designs of the manipulator having a relatively larger workspace and lower power consumption. The results are verified through numerical examples.

Dynamic Modeling of a High-Dynamic Flight Simulator

2014 ◽  
Vol 687-691 ◽  
pp. 610-615 ◽  
Author(s):  
Hui Liu ◽  
Li Wen Guan
Keyword(s):  
Dynamic Modeling ◽  
Degrees Of Freedom ◽  
Flight Simulator ◽  
Inverse Dynamic ◽  
Dynamic Formulation ◽  
Time Histories ◽  
Rotational Degrees Of Freedom ◽  
High Dynamic ◽  
Euler Approach ◽  
Simulation Results

High-dynamic flight simulator (HDFS), using a centrifuge as its motion base, is a machine utilized for simulating the acceleration environment associated with modern advanced tactical aircrafts. This paper models the HDFS as a robotic system with three rotational degrees of freedom. The forward and inverse dynamic formulations are carried out by the recursive Newton-Euler approach. The driving torques acting on the joints are determined on the basis of the inverse dynamic formulation. The formulation has been implemented in two numerical simulation examples, which are used for calculating the maximum torques of actuators and simulating the time-histories of kinematic and dynamic parameters of pure trapezoid Gz-load command profiles, respectively. The simulation results can be applied to the design of the control system. The dynamic modeling approach presented in this paper can also be generalized to some similar devices.

Modelling and Design of an Airship Crane

2018 ◽  
Author(s):  
Naoufel Azouz ◽  
Mahmoud Khamlia ◽  
Fida Benabdallah ◽  
Fatma Guesmi
Keyword(s):  
Dynamic Modeling ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Main Function ◽  
Precise Control ◽  
Six Degrees Of Freedom ◽  
Loading And Unloading ◽  
Position And Orientation

This paper presents the design and the dynamic modeling of a Smart Crane called CHAYASC, designed to equip wide-body airship, which has to carry out loading and unloading operations from a certain altitude. The main function of this crane is to lift, stabilize, maneuver and position large loads by having precise control of the position and orientation of these loads according to the six degrees of freedom. The CHAYASC is based in particular on a Cable Driven Parallel Manipulator and will have a dual mission: 1) deposit and arrange the containers in the hold of the airship, 2) lift and stabilize the containers suspended during a sudden movement of the airship under the effect of a gust of wind.

Kinematics and dynamics of a parallel manipulator with a new architecture

Robotica ◽  
2000 ◽  
Vol 18 (5) ◽  
pp. 535-543 ◽  
Author(s):  
A. Fattah ◽  
G. Kasaei
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
Orthogonal Complement ◽  
Flight Simulator ◽  
Kinematics And Dynamics ◽  
Dynamical Equations ◽  
Euler’S Equations ◽  
Euler's Equations ◽  
Moving Platform

In this paper, the kinematics and dynamics of a parallel manipulator with a new architecture supposed to be used as a moving mechanism in a flight simulator project is studied. This manipulator with three independent degrees of freedom consists of a moving platform connected to a based platform by means of three legs. Kinematic solutions for this manipulator at position, velocity and acceleration levels are obtained. Moreover, the dynamical equations of motion of the manipulator are determined using Newton-Euler's equations and applying the natural orthogonal complement (NOC) method. Using kinematics and dynamics and also performing simulation for different manoeuvres of moving platform, the motion and the actuator forces of the legs are obtained.

scholarly journals ALGORITHM OF EULER-LAGRANGE METHOD FOR DEISGNING OF DYNAMIC MODEL

2018 ◽  
pp. 89-95
Author(s):  
Virgala Ivan ◽  
Filakovský Filip
Keyword(s):  
Dynamic Model ◽  
Dynamic Modeling ◽  
Degrees Of Freedom ◽  
Computing Time ◽  
Kinematic Model ◽  
Difficult Problem ◽  
Kinematic Structure ◽  
Lagrange Method ◽  
Inverse Dynamic ◽  
Whole Process

Urgency of the research. Nowadays robotics and mechatronics come to be mainstream. With development in these areas also grow computing fastidiousness. Since there is significant focus on numerical modeling and algorithmization in kinematic and dynamic modeling. Target setting. By automation of whole process of dynamic model design the errors are eliminated as well as the time of designing significantly decreases. Actual scientific researches and issues analysis. Designing of dynamic model by analytical way is very difficult especially in the cases considering high number of DOF. For hyperredundant manipulators it is practically impossible. From this reason whole process is automatized. Uninvestigated parts of general matters defining. The theory of Euler – Lagrange method is automatized by means of robotic view on this issue. The research objective. In the paper, an algorithm for design of dynamic model was introduced. The statement of basic materials. The paper deals with automatic design process of dynamic model for serial kinematic structure mechanisms. In the paper Euler – Lagrange formula is discussed. Analytical way of dynamic modeling should be difficult problem especially for mechanisms with high number of degrees of freedom. From this reason the paper shows the way of automatically designing of dynamic modeling in MATLAB. Our study shows dependence of computing time on increasing DOF. The relation is expressed by function of 3rd order. Subsequently the paper presents automatically generated inverse dynamic model in cooperation with inverse kinematic model as well as trajectory planning task. Conclusions. The paper introduces automatically generated dynamic model for mechanisms with serial kinematic structure. The paper also established the time for designing of dynamic model for several mechanisms with changing DOF.

Task-based torque minimization of a 3-PṞR spherical parallel manipulator

Robotica ◽  
2021 ◽  
pp. 1-30
Author(s):  
Soheil Zarkandi
Keyword(s):  
Closed Form ◽  
Dynamic Modeling ◽  
Dynamic Equation ◽  
Parallel Manipulator ◽  
Optimization Problem ◽  
Dynamic Constraints ◽  
Part C ◽  
Euler Approach ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

Abstract A comprehensive dynamic modeling and actuator torque minimization of a new symmetrical three-degree-of-freedom (3-DOF) 3-PṞR spherical parallel manipulator (SPM) is presented. Three actuating systems, each of which composed of an electromotor, a gearbox and a double Rzeppa-type driveshaft, produce input torques of the manipulator. Kinematics of the 3-PṞR SPM was recently studied by the author (Zarkandi, Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci. 2020, https://doi.org/10.1177%2F0954406220938806). In this paper, a closed-form dynamic equation of the manipulator is derived with the Newton–Euler approach. Then, an optimization problem with kinematic and dynamic constraints is presented to minimize torques of the actuators for implementing a given task. The results are also verified by the SimMechanics model of the manipulator.

Determination of the Workspace of a Three-Degrees-of-Freedom Parallel Manipulator Using a Three-Dimensional Computer-Aided-Design Software Package and the Concept of Virtual Chains1

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Andrew Johnson ◽  
Xianwen Kong ◽  
James Ritchie
Keyword(s):  
Computer Aided Design ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Graphical Representation ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Workspace Analysis ◽  
Computer Aided ◽  
Aided Design

The determination of workspace is an essential step in the development of parallel manipulators. By extending the virtual-chain (VC) approach to the type synthesis of parallel manipulators, this technical brief proposes a VC approach to the workspace analysis of parallel manipulators. This method is first outlined before being illustrated by the production of a three-dimensional (3D) computer-aided-design (CAD) model of a 3-RPS parallel manipulator and evaluating it for the workspace of the manipulator. Here, R, P and S denote revolute, prismatic and spherical joints respectively. The VC represents the motion capability of moving platform of a manipulator and is shown to be very useful in the production of a graphical representation of the workspace. Using this approach, the link interferences and certain transmission indices can be easily taken into consideration in determining the workspace of a parallel manipulator.

Kinematics of a Fully-Decoupled Remote Center-of-Motion Parallel Manipulator for Minimally Invasive Surgery

2012 ◽  
Vol 6 (2) ◽  
Author(s):  
Chin-Hsing Kuo ◽  
Jian S. Dai
Keyword(s):  
Minimally Invasive Surgery ◽  
Minimally Invasive ◽  
Invasive Surgery ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Surgical Instruments ◽  
End Effector ◽  
Minimally Invasive Surgical ◽  
Inverse Kinematics Problem

A crucial design challenge in minimally invasive surgical (MIS) robots is the provision of a fully decoupled four degrees-of-freedom (4-DOF) remote center-of-motion (RCM) for surgical instruments. In this paper, we present a new parallel manipulator that can generate a 4-DOF RCM over its end-effector and these four DOFs are fully decoupled, i.e., each of them can be independently controlled by one corresponding actuated joint. First, we revisit the remote center-of-motion for MIS robots and introduce a projective displacement representation for coping with this special kinematics. Next, we present the proposed new parallel manipulator structure and study its geometry and motion decouplebility. Accordingly, we solve the inverse kinematics problem by taking the advantage of motion decouplebility. Then, via the screw system approach, we carry out the Jacobian analysis for the manipulator, by which the singular configurations are identified. Finally, we analyze the reachable and collision-free workspaces of the proposed manipulator and conclude the feasibility of this manipulator for the application in minimally invasive surgery.

Experimental and Numerical Hydrodynamic Modeling of an Underwater Manipulator

2001 ◽  
Author(s):  
A. Khanicheh ◽  
A. Tehranian ◽  
A. Meghdari ◽  
M. S. Sadeghipour
Keyword(s):  
Drag Coefficient ◽  
Dynamic Modeling ◽  
Hydrodynamic Model ◽  
Degrees Of Freedom ◽  
Added Mass ◽  
Hydrodynamic Modeling ◽  
Degree Of Freedom ◽  
Experimental Results ◽  
Underwater Manipulator ◽  
Three Degrees Of Freedom

Abstract This paper presents the kinematics and dynamic modeling of a three-link (3-DOF) underwater manipulator where the effects of hydrodynamic forces are investigated. In our investigation, drag and added mass coefficients are not considered as constants. In contrast, the drag coefficient is a variable with respect to all relative parameters. Experiments were conducted to validate the hydrodynamic model for a one degree-of-freedom manipulator up to a three degrees-of-freedom manipulator. Finally, the numerical and experimental results are compared and thoroughly discussed.

Sign in / Sign up

Export Citation Format

Share Document