Real-time cryo-deformation of polypropylene and impact-modified polypropylene in the transmission electron microscope

1993 ◽  
Vol 51 ◽  
pp. 892-893
Author(s):  
Robert C. Cieslinski ◽  
H. Craig Silvis ◽  
Daniel J. Murray
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Failure Mechanisms ◽  
Brittle Transition ◽  
Molded Part ◽  
Transmission Electron ◽  
Solvent Cast ◽  
The Impact ◽  
Annealed Copper ◽  
Dynamic Plane

An understanding of the mechanical behavior polymers in the ductile-brittle transition region will result in materials with improved properties. A technique has been developed that allows the realtime observation of dynamic plane stress failure mechanisms in the transmission electron microscope. With the addition of a cryo-tensile stage, this technique has been extented to -173°C, allowing the observation of deformation during the ductile-brittle transition.The technique makes use of an annealed copper cartridge in which a thin section of bulk polymer specimen is bonded and plastically deformed in tension in the TEM using a screw-driven tensile stage. In contrast to previous deformation studies on solvent-cast films, this technique can examine the frozen-in morphology of a molded part.The deformation behavior of polypropylene and polypropylene impact modified with EPDM (ethylene-propylene diene modified) and PE (polyethylene) rubbers were investigated as function of temperature and the molecular weight of the impact modifier.

A Study of Membrane Impact on Spatial Resolution of Liquid In Situ Transmission Electron Microscope

2020 ◽  
Vol 26 (1) ◽  
pp. 126-133
Author(s):  
Ming Li ◽  
Ruth Knibbe
Keyword(s):  
Electron Microscope ◽  
Spatial Resolution ◽  
Transmission Electron Microscope ◽  
Signal To Noise Ratio ◽  
Chromatic Aberration ◽  
Membrane Thickness ◽  
Additional Material ◽  
Transmission Electron ◽  
The Impact

AbstractMicrochip technology with electron transparent membranes is a key component for in situ liquid transmission electron microscope (TEM) characterization. The membranes can significantly influence the TEM imaging spatial resolution, not only due to introducing additional material layers but also due to the associated bulging. The membrane bulging is largely defined by the membrane materials, thickness, and short dimension. The impact of the membrane on the spatial resolution, especially the extent of its bulging, was systematically investigated through the impact on the signal-to-noise ratio, chromatic aberration, and beam broadening. The optimization of the membrane parameters is the key component when designing the in situ TEM liquid cell. The optimal membrane thickness of 50 nm was found which balances the impact of membrane bulging and membrane thickness. Beyond this, the short membrane window dimension and the chip nominal spacing should be minimized. However, these two parameters have practical limitations in regards to chip handling.

scholarly journals Assessment of Changes in Microstructure and Hardness of Bearing Steel for Operation at a High Temperature Caused by Short-Term Overheating

2020 ◽  
Vol 50 (4) ◽  
pp. 89-110
Author(s):  
Krzysztof Łęczycki ◽  
Sebastian Gronek
Keyword(s):  
Electron Microscope ◽  
High Temperature ◽  
Elevated Temperature ◽  
Transmission Electron Microscope ◽  
Bearing Steel ◽  
Short Term ◽  
Turbine Engine ◽  
Bearing Ring ◽  
Transmission Electron ◽  
The Impact

AbstractThe paper presented research results of the impact of short-term overheating of samples collected from the outer bearing ring suitable for the operation at elevated temperature installed in the turbine engine on the microstructure and hardness of the material. The samples were annealed at the following temperatures: 500, 600, 700, 800, 900 and 1000°C; and then cooled in still air. Microstructure examinations were conducted under metallographic microscope and transmission electron microscope.

Improvements in the X-Ray Analytical Capabilities of a Scanning Transmission Electron Microscope by Spherical-Aberration Correction

2006 ◽  
Vol 12 (6) ◽  
pp. 515-526 ◽  
Author(s):  
M. Watanabe ◽  
D.W. Ackland ◽  
A. Burrows ◽  
C.J. Kiely ◽  
D.B. Williams ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Spherical Aberration ◽  
Scanning Transmission Electron Microscope ◽  
Analytical Sensitivity ◽  
X Ray ◽  
Scanning Transmission Electron ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
The Impact

A Nion spherical-aberration (Cs) corrector was recently installed on Lehigh University's 300-keV cold field-emission gun (FEG) Vacuum Generators HB 603 dedicated scanning transmission electron microscope (STEM), optimized for X-ray analysis of thin specimens. In this article, the impact of the Cs-corrector on X-ray analysis is theoretically evaluated, in terms of expected improvements in spatial resolution and analytical sensitivity, and the calculations are compared with initial experimental results. Finally, the possibilities of atomic-column X-ray analysis in a Cs-corrected STEM are discussed.

A Reproducible Selective Stain for Cardiac Sarcoplasmic Reticulum

1974 ◽  
Vol 32 ◽  
pp. 214-215
Author(s):  
R. A. Waugh ◽  
J. R. Sommer
Keyword(s):  
Complex System ◽  
Electron Microscope ◽  
Sarcoplasmic Reticulum ◽  
Transmission Electron Microscope ◽  
Electron Microscopic ◽  
Cardiac Sarcoplasmic Reticulum ◽  
Transmission Electron

Cardiac sarcoplasmic reticulum (SR) is a complex system of intracellular tubules that, due to their small size and juxtaposition to such electron-dense structures as mitochondria and myofibrils, are often inconspicuous in conventionally prepared electron microscopic material. This study reports a method with which the SR is selectively “stained” which facilitates visualizationwith the transmission electron microscope.

Surface Structure of the Spores of Glugea Weissenbergi

1969 ◽  
Vol 27 ◽  
pp. 238-239
Author(s):  
Sanford H. Vernick ◽  
Anastasios Tousimis ◽  
Victor Sprague
Keyword(s):  
Electron Microscope ◽  
Surface Structure ◽  
Transmission Electron Microscope ◽  
Mature Spore ◽  
Spore Surface ◽  
Sectioned Material ◽  
Transmission Electron ◽  
Surface Detail

Recent electron microscope studies have greatly expanded our knowledge of the structure of the Microsporida, particularly of the developing and mature spore. Since these studies involved mainly sectioned material, they have revealed much internal detail of the spores but relatively little surface detail. This report concerns observations on the spore surface by means of the transmission electron microscope.

A New High Resolution Transmission Electron Microscope with Second-Zone Objective Lens

1969 ◽  
Vol 27 ◽  
pp. 176-177 ◽  
Author(s):  
H. Tochigi ◽  
H. Uchida ◽  
S. Shirai ◽  
K. Akashi ◽  
D. J. Evins ◽  
...  
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Transmission Electron Microscope ◽  
Objective Lens ◽  
High Excitation ◽  
Transmission Electron ◽  
New Instrument

A New High Excitation Objective Lens (Second-Zone Objective Lens) was discussed at Twenty-Sixth Annual EMSA Meeting. A new commercially available Transmission Electron Microscope incorporating this new lens has been completed.Major advantages of the new instrument allow an extremely small beam to be produced on the specimen plane which minimizes specimen beam damages, reduces contamination and drift.

X-ray microanalysis of thin specimens in the transmission electron microscope at voltages up to 1000 Kv.

1978 ◽  
Vol 36 (1) ◽  
pp. 540-541
Author(s):  
G. Cliff ◽  
M.J. Nasir ◽  
G.W. Lorimer ◽  
N. Ridley
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Weight Fraction ◽  
Present Series ◽  
Constant Independent ◽  
X Ray ◽  
Transmission Electron ◽  
Series Of Experiments ◽  
Image Position ◽  
X Ray Absorption

In a specimen which is transmission thin to 100 kV electrons - a sample in which X-ray absorption is so insignificant that it can be neglected and where fluorescence effects can generally be ignored (1,2) - a ratio of characteristic X-ray intensities, I1/I2 can be converted into a weight fraction ratio, C1/C2, using the equationwhere k12 is, at a given voltage, a constant independent of composition or thickness, k12 values can be determined experimentally from thin standards (3) or calculated (4,6). Both experimental and calculated k12 values have been obtained for K(11<Z>19),kα(Z>19) and some Lα radiation (3,6) at 100 kV. The object of the present series of experiments was to experimentally determine k12 values at voltages between 200 and 1000 kV and to compare these with calculated values.The experiments were carried out on an AEI-EM7 HVEM fitted with an energy dispersive X-ray detector.

Aspects of microanalysis in a transmission electron microscope

1978 ◽  
Vol 36 (1) ◽  
pp. 510-511
Author(s):  
R. Sinclair ◽  
B.E. Jacobson
Keyword(s):  
Grain Size ◽  
Electron Beam ◽  
Electron Microscope ◽  
Chemical Analysis ◽  
Transmission Electron Microscope ◽  
Vapor Deposition ◽  
Critical Currents ◽  
X Ray ◽  
Fine Grain ◽  
Transmission Electron

INTRODUCTIONThe prospect of performing chemical analysis of thin specimens at any desired level of resolution is particularly appealing to the materials scientist. Commercial TEM-based systems are now available which virtually provide this capability. The purpose of this contribution is to illustrate its application to problems which would have been intractable until recently, pointing out some current limitations.X-RAY ANALYSISIn an attempt to fabricate superconducting materials with high critical currents and temperature, thin Nb3Sn films have been prepared by electron beam vapor deposition [1]. Fine-grain size material is desirable which may be achieved by codeposition with small amounts of Al2O3 . Figure 1 shows the STEM microstructure, with large (∽ 200 Å dia) voids present at the grain boundaries. Higher quality TEM micrographs (e.g. fig. 2) reveal the presence of small voids within the grains which are absent in pure Nb3Sn prepared under identical conditions. The X-ray spectrum from large (∽ lμ dia) or small (∽100 Ǻ dia) areas within the grains indicates only small amounts of A1 (fig.3).

The direct determination of magnetic domain wall profiles using a split detector STEM

1978 ◽  
Vol 36 (1) ◽  
pp. 466-467
Author(s):  
J.N. Chapman ◽  
P.E. Batson ◽  
E.M. Waddell ◽  
R.P. Ferrier
Keyword(s):  
Electron Microscope ◽  
Domain Wall ◽  
Transmission Electron Microscope ◽  
Domain Walls ◽  
Photographic Plate ◽  
Magnetic Domain ◽  
Direct Determination ◽  
Quantitative Information ◽  
Scanning Transmission Electron Microscope ◽  
Transmission Electron

By far the most commonly used mode of Lorentz microscopy in the examination of ferromagnetic thin films is the Fresnel or defocus mode. Use of this mode in the conventional transmission electron microscope (CTEM) is straightforward and immediately reveals the existence of all domain walls present. However, if such quantitative information as the domain wall profile is required, the technique suffers from several disadvantages. These include the inability to directly observe fine image detail on the viewing screen because of the stringent illumination coherence requirements, the difficulty of accurately translating part of a photographic plate into quantitative electron intensity data, and, perhaps most severe, the difficulty of interpreting this data. One solution to the first-named problem is to use a CTEM equipped with a field emission gun (FEG) (Inoue, Harada and Yamamoto 1977) whilst a second is to use the equivalent mode of image formation in a scanning transmission electron microscope (STEM) (Chapman, Batson, Waddell, Ferrier and Craven 1977), a technique which largely overcomes the second-named problem as well.

A General Method for Spectrometer Design in the Scoff Approximation

1976 ◽  
Vol 34 ◽  
pp. 538-539
Author(s):  
J. R. Fields
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Energy Analysis ◽  
Incident Beam ◽  
Scanning Transmission Electron Microscope ◽  
Chemical Identification ◽  
Scanning Transmission Electron ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
General Method

The energy analysis of electrons scattered by a specimen in a scanning transmission electron microscope can improve contrast as well as aid in chemical identification. In so far as energy analysis is useful, one would like to be able to design a spectrometer which is tailored to his particular needs. In our own case, we require a spectrometer which will accept a parallel incident beam and which will focus the electrons in both the median and perpendicular planes. In addition, since we intend to follow the spectrometer by a detector array rather than a single energy selecting slit, we need as great a dispersion as possible. Therefore, we would like to follow our spectrometer by a magnifying lens. Consequently, the line along which electrons of varying energy are dispersed must be normal to the direction of the central ray at the spectrometer exit.

Sign in / Sign up

Export Citation Format

Share Document