High-resolution observations of metastable γ’ precipitation in Al-15at.%Ag

1996 ◽  
Vol 54 ◽  
pp. 1004-1005
Author(s):  
N. V. Larcher ◽  
I. G. Solorzano
Keyword(s):  
Discontinuous Precipitation ◽  
Equilibrium Phase ◽  
Quantitative Description ◽  
Present Contribution ◽  
Α Phase ◽  
The Matrix ◽  
Aging Sequence ◽  
Matrix Precipitation ◽  
Considerable Detail ◽  
Kinetics Of

It is currently well established that, for an Al-Ag alloy quenched from the α phase and aged within the metastable solvus, the aging sequence is: supersaturated α → GP zones → γ’ → γ (Ag2Al). While GP zones and plate-shaped γ’ are metastable phases, continuously distributed in the matrix, formation of the equilibrium phase γ takes place at grain boundaries by discontinuous precipitation (DP). The crystal structure of both γ’ and γ is hep with the following orientation relationship with respect to the fee α matrix: {0001}γ′,γ // {111}α, <1120>γ′,γ, // <110>α.The mechanisms and kinetics of continuous matrix precipitation (CMP) in dilute Al-Ag alloys have been studied in considerable detail. The quantitative description of DP kinetics, however, has received less attention. The present contribution reports the microstructural evolution resulting from aging an Al-Ag alloy with Ag content higher than those previously reported in the literature, focusing the observations of γ' plate-shaped metastable precipitates.

scholarly journals Continuous Cooling Transformation Behaviour and Bainite Transformation Kinetics of 23CrNi3Mo Carburised Steel

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 48
Author(s):  
Wenjun Song ◽  
Min Lei ◽  
Mingpan Wan ◽  
Chaowen Huang
Keyword(s):  
Phase Transformation ◽  
Volume Fraction ◽  
Austenite Formation ◽  
Steel Matrix ◽  
Transformation Kinetics ◽  
Bainite Transformation ◽  
Continuous Cooling ◽  
The Matrix ◽  
Dimensional Growth ◽  
Kinetics Of

In this study, the phase transformation behaviour of the carburised layer and the matrix of 23CrNi3Mo steel was comparatively investigated by constructing continuous cooling transformation (CCT) diagram, determining the volume fraction of retained austenite (RA) and plotting dilatometric curves. The results indicated that Austenite formation start temperature (Ac1) and Austenite formation finish temperature (Ac3) of the carburised layer decreased compared to the matrix, and the critical cooling rate (0.05 °C/s) of martensite transformation is significantly lower than that (0.8 °C/s) of the matrix. The main products of phase transformation in both the carburised layer and the matrix were martensite and bainite microstructures. Moreover, an increase in carbon content resulted in the formation of lamellar martensite in the carburised layer, whereas the martensite in the matrix was still lath. Furthermore, the volume fraction of RA in the carburised layer was higher than that in the matrix. Moreover, the bainite transformation kinetics of the 23CrNi3Mo steel matrix during the continuous cooling process indicated that the mian mechanism of bainite transformation of the 23CrNi3Mo steel matrix is two-dimensional growth and one-dimensional growth.

scholarly journals Oxygen Induced Phase Transformation in TC21 Alloy with a Lamellar Microstructure

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 163
Author(s):  
Shu Wang ◽  
Yilong Liang ◽  
Hao Sun ◽  
Xin Feng ◽  
Chaowen Huang
Keyword(s):  
Electron Microscopy ◽  
Phase Transformation ◽  
Oxygen Uptake ◽  
Titanium Alloys ◽  
Electron Backscatter Diffraction ◽  
Lamellar Microstructure ◽  
Α Phase ◽  
Transmission Electron ◽  
The Matrix ◽  
Oxygen Ingress

The main objective of the present study was to understand the oxygen ingress in titanium alloys at high temperatures. Investigations reveal that the oxygen diffusion layer (ODL) caused by oxygen ingress significantly affects the mechanical properties of titanium alloys. In the present study, the high-temperature oxygen ingress behavior of TC21 alloy with a lamellar microstructure was investigated. Microstructural characterizations were analyzed through optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). Obtained results demonstrate that oxygen-induced phase transformation not only enhances the precipitation of secondary α-phase (αs) and forms more primary α phase (αp), but also promotes the recrystallization of the ODL. It was found that as the temperature of oxygen uptake increases, the thickness of the ODL initially increases and then decreases. The maximum depth of the ODL was obtained for the oxygen uptake temperature of 960 °C. In addition, a gradient microstructure (αp + β + βtrans)/(αp + βtrans)/(αp + β) was observed in the experiment. Meanwhile, it was also found that the hardness and dislocation density in the ODL is higher than that that of the matrix.

Kinetics of the α-α′ phase separation in a 14%Cr oxide dispersion steel at intermediate temperatures

2020 ◽  
pp. 129088
Author(s):  
Yael Templeman ◽  
Malki Pinkas ◽  
Eli Brosh ◽  
Einat Strumza ◽  
Shmuel Hayun ◽  
...  
Keyword(s):  
Phase Separation ◽  
Oxide Dispersion ◽  
Α Phase ◽  
Kinetics Of

Correlations for Interaction Layer Growth in U-Mo/Al Dispersion Fuels

2017 ◽  
Vol 375 ◽  
pp. 29-39
Author(s):  
Boris A. Tarasov ◽  
Stepan N. Nikitin ◽  
Dmitry P. Shornikov ◽  
Maria S. Tarasova ◽  
Igor I. Konovalov
Keyword(s):  
Growth Rate ◽  
Growth Process ◽  
Aluminum Matrix ◽  
Layer Growth ◽  
Radiation Diffusion ◽  
Fission Rate ◽  
Interaction Layer ◽  
The Matrix ◽  
Mechanism And Kinetics ◽  
Kinetics Of

Paper presents the results of the growth rate of the interaction layer of uranium-molybdenum dispersed fuel in aluminum matrix and influence of silicon alloying on it. The growth process of amorphous interaction layer depends on the radiation diffusion which is proportional to the fission rate in the power of 1⁄4. The alloying of the matrix by silicon does not lead to a change in the mechanism and kinetics of the interaction layer growth, but only slows it down.

The effect of composition and cooling rate on the structure of rapidly solidified (Fe, Ni)3Al–C alloys

1989 ◽  
Vol 4 (1) ◽  
pp. 44-49 ◽  
Author(s):  
S. A. Myers ◽  
C. C. Koch
Keyword(s):  
Cooling Rate ◽  
Base Alloy ◽  
Weight Percent ◽  
Quench Rate ◽  
Transmission Electron ◽  
Metastable Structures ◽  
Metastable Structure ◽  
The Matrix ◽  
Rapidly Solidified ◽  
Kinetics Of

There is controversy in the literature regarding the existence of the metastable γ′ phase with an ordered Ll2 structure in rapidly solidified Fe–Ni–Al–C alloys. In this study, the quench rate–metastable structure dependence was examined in the Fe–20Ni–8Al–2C (weight percent) alloy. The effect of silicon on the kinetics of phase formation was studied by adding two weight percent silicon to a base alloy of Fe–20Ni–8Al–2C. Samples were rapidly solidified in an arc hammer apparatus and examined by transmission electron microscopy. In the Fe–20Ni–8Al–2C alloy, the nonequilibrium γ′ and γ phases were found in foils 65 to 100 μm thick. At higher quench rates, i.e., thinner samples, the matrix was observed to be disordered fcc γ with K-carbide precipitates. Samples containing silicon were found to have a matrix composed of γ′ and γ structures when the foils were thicker than 40 μm. At higher quench rates, the matrix was disordered fcc γ with K-carbide precipitates. The nonequilibrium γ′ and γ structures are present in samples with or without silicon, but are observed at higher cooling rates with the addition of silicon. This sensitivity to cooling rate and composition in resulting metastable structures may explain the differences reported in the literature for these rapidly solidified materials.

Primary products and processes in the γ-radiolysis of 2-methyltetrahydrofuran

1965 ◽  
Vol 285 (1402) ◽  
pp. 319-338 ◽  
Keyword(s):  
Glassy Phase ◽  
Kcal Mole ◽  
Radical Species ◽  
Molecule Reaction ◽  
Positive Ions ◽  
Primary Products ◽  
Diffusion Controlled ◽  
Thermal Bleaching ◽  
The Matrix ◽  
Kinetics Of

From a study of the u. v., visible, near i. r. and e. s. r. spectra induced by γ -irradiation at 77°K in glassy MTHF and in glassy MTHF containing various additives and from a study of controlled temperature increases on these spectra, the following conclusions are drawn. (1) The primary products of the radiolysis are electrons ( e - ) and positive ions ( MTHF + ) which undergo a rapid ion-molecule reaction to give O CH 3 radicals ( R ⋅). (2) e - can either be trapped in the glassy MTHF matrix or can be captured by either napththalene, ferric chloride, carbon tetrachloride, nitrous oxide or trans -stilbene if these substances are present. (3) The e - T are bleachable by light or heat and disappear independently of the radicals R⋅ without either augmentation of R⋅ or the production of any new radical species. (4) e - T and R⋅ disappear thermally and independently by second-order reactions, the rate constants being K e - + e - (M -1 S -1 ) = 10 12⋅4±1⋅1 exp ─ [0⋅85 ± 0⋅10 kcal/mole/ R ( T ─ 75)] and K R˙ + R˙ (M -1 S -1 ) = 10 13⋅3±1⋅4 exp ─ [1⋅20 ± 0⋅15 kcal/mole/ R ( T ─ 75)]. These rate expressions suggest that both reactions are diffusion controlled at low temperatures in the glassy phase. (5) The kinetics of the thermal bleaching of e - T indicate that the electrons migrate distances of about 150 Å from their parent positive ions before being trapped in the matrix. (6) The effect of FeCl 3 in reducing the formation of e - T at 77°K and its lack of effect on the thermal bleaching of e - T suggests that the reaction e - + FeCl 3 → FeCl 2 + Cl - only occurs before the electron is thermalized.

Effect of Excess PbO on the Kinetics of the Growth of PMNT Polycrystals by Templated Grain Growth Method

2005 ◽  
Vol 475-479 ◽  
pp. 1137-1140
Author(s):  
Lili Zhao ◽  
Feng Gao ◽  
Wei Min Wang ◽  
Chang Sheng Tian
Keyword(s):  
Grain Growth ◽  
Templated Grain Growth ◽  
Experimental Conditions ◽  
Precipitation Mechanism ◽  
Oriented Structure ◽  
Diffusion Controlled ◽  
The Matrix ◽  
Growth Method ◽  
Final Composition ◽  
Kinetics Of

The oriented 0.67Pb (Mg1/3Nb2/3)O3-0.33PbTiO3 (PMNT) polycrystals were prepared by the conventional ceramic technique and the templated grain growth method adding excess PbO in the matrix. Kinetics of the development of oriented structure was investigated systemically. In the presence of PbO liquid phase, the oriented PMNT polycrystals mainly grow by the dissolution-precipitation mechanism. The diffusion is determined by the sintering temperature and the PbO-excess content in the matrix. The thickness of oriented PMNT polycrystals displays a t1/3 dependence, which is characteristic of diffusion-controlled growth. For the thicker oriented structure, 20% excess PbO in the PMNT matrix and 1150oC for 10h are the proper experimental conditions. Moreover, the addition of PbO in the matrix hardly affects the final composition of ceramic matrix.

Sign in / Sign up

Export Citation Format

Share Document