A new phase transformation path from nanodiamond to new-diamond via an intermediate carbon onion

Nanoscale ◽  
2014 ◽  
Vol 6 (24) ◽  
pp. 15098-15106 ◽  
Author(s):  
J. Xiao ◽  
J. L. Li ◽  
P. Liu ◽  
G. W. Yang

A new phase transformation path from nanodiamond to n-diamond via an intermediate carbon onion in the unique process of laser ablation in water.

1967 ◽  
Vol 38 (5) ◽  
pp. 2042-2046 ◽  
Author(s):  
M. D. Banus ◽  
Mary C. Lavine

1970 ◽  
Vol 14 ◽  
pp. 67-77 ◽  
Author(s):  
P. Krishna ◽  
R. C. Marshall

AbstractThis paper reports the results of a detailed X-ray diffraction study of a new phase-transformation observed in SiC crystals grown by a vapour-liquid-solid mechanism involving the hydrogen-reduction of methyltrichlorosilane. The 10.ℓ reciprocal lattice rows of these crystals, as recorded on X-ray diffraction photographs, reveal sharp reflections corresponding to the hexagonal close-packed 2H (ABAB….) structure and sometimes also corresponding to the cubic close-packed 3C (ABCABC…) structure. These reflections are invariably connected by a diffuse but continuous streak whose intensity is a measure of the random faulting on the basal planes. The crystals were needle shaped and the structure sometimes varied along their length.Several crystals were annealed in an inert atmosphere at progressively higher temperatures and their 10.ℓ reciprocal lattice row re-examined to determine the annealing behaviour as well as possible structural transformations. For a number of dark green needles having a faulted 2H structure the 2H reflections disappeared around 1400° C and the 10.ℓ reciprocal lattice row revealed only a continuous streak with increased intensity around positions for 3C reflections. On further heating the structure went over to a strongly faulted 3C. Around 1600°C the appearance of a 6H structure became discernible while highly diffuse 30 reflections still persisted. The reversible part of the transformations, if any, could not be observed. Some of the structures were, however, found to be much more stable and did not transform even up to 1650° C.The above results, in particular the discovery of a 2H-3C phase-transformation around 1400°C, throw fresh light on the thermodynamic stability of the different SiC types. The mechanism of the 2H-3C transformation, the possible influence of faults and impurities and the thermal stability of various SiC structures are discussed on the basis of the experimental results stated above.


2018 ◽  
Vol 240 ◽  
pp. 01020
Author(s):  
Łukasz Łach ◽  
Robert Straka ◽  
Dmytro Svyetlichnyy

In heat treatment of materials, the phase transformation is an important phenomenon, which determines the final microstructure. The microstructure of different materials described by such parameters as morphology, grain size, phase fraction and their spatial distribution, largely effects on the mechanical and functional properties of final products. The subject of the work is a development of a hybrid model based on CA and Lattice Boltzmann method (LBM) for modeling of the diffusion phase transformation. The model has a modular structure and simulates three basic phenomena: diffusion, heat flow and phase transformation. The objective of the paper is a presentation of module of the hybrid model for simulation of heat flow with considering of enthalpy of transformation. This is one of the stages in the development of the model and obtained results will be used in a combined solution of heat transfer and diffusion during the modeling of diffusion phase transformations. Lately, the model will be extended to three dimensions and will use hybrid computational systems (CPU and GPU). CA and LBM are used in the model as follows. LBM is used for modeling of heat flow, while CA is used for modeling of microstructure evolution during the phase transformation. The main factors considered in the model are the enthalpy of transformation and heat transfer. The paper presents the results of the modeling of the new phase growth determined by different values of overcooling affecting on different values in the enthalpy of transformation. The heat flow is simulated and the results for some modeling variants are shown. Examples of simulation results obtained from the modeling are presented in the form of images, which present the growth of new phase and temperature distributions.


2012 ◽  
Vol 490-495 ◽  
pp. 3109-3113
Author(s):  
Xiang Peng Xiao ◽  
Bai Qing Xiong ◽  
Qiang Song Wang ◽  
Guo Liang Xie ◽  
Li Jun Peng

The effects of aging temperature and aging time on properties of Cu-2.1Ni-0.5Si -0.2Zr-0.05Cr (wt.%) alloy were studied. The transformation ratio of new phase in Cu-2.1Ni-0.5Si-0.2Zr-0.05Cr alloy was calculated when aging at 400°C, 450°C and 500°C by measuring electrical conductivity, the relation between the electrical conductivity and the quantity of new phase. The Avrami-equation of phase transformation kinetics and the Avrami-equation of electrical conductivity during aging were established for Cu-2.1Ni-0.5Si-0.2Zr-0.05Cr alloy, on the basis of linear relationship between the electric conductivity and the volume fraction of precipitates. The calculated values of electrical conductivity well consistent with those of experiment can provide reference on the alloy of production process. The characteristics of precipitates in the alloy after solution treatment and cold rolling were established, and the results show the precipitate was δ-Ni2Si phase.


2012 ◽  
Vol 36 (3) ◽  
pp. 619-625 ◽  
Author(s):  
Liang Liu ◽  
Feng Cao ◽  
Tao Yao ◽  
Yang Xu ◽  
Min Zhou ◽  
...  

2004 ◽  
Vol 467-470 ◽  
pp. 819-824 ◽  
Author(s):  
Tadao Watanabe ◽  
Kouichi Obara ◽  
Sadahiro Tsurekawa

In-situ observations of a/g phase transformation were made to study the effect of grain boundary microstructure of the generation of a new phase and the migration of a/g interphase boundaries in an Iron-4.2at.%Cr alloy. It was found that triple junctions with more random boundaries could be the primary nucleation sites, while triple junctions with low angle and low S coincidence boundaries did not play a role as preferential sites. The migration of a/g interphase boundaries during heating across the transformation temperature showed the two stage behaviour characterized first by a stage with a migration velocity of 0.33-0.75µm/s and secondly a stage with 3.7-7.6 µm/s. It was also found that abnormal grain growth and a high density of S3 coincidence boundaries could occur in the a/bcc phase after cycling of a/g/ a phase transformation.


2008 ◽  
Vol 33-37 ◽  
pp. 1351-1358 ◽  
Author(s):  
Tatsuo Inoue

Phenomenological mechanism of transformation plasticity is proposed in the first part of the paper by use of simple model why stress in mother phase increases to reach yielding due to progressing new phase and to induce plastic deformation even under small applied stress. Based on the discussion, a unified constitutive model including transformation-induced and ordinal thermomechanical plastic strain rates by introducing an effect of varying phases during phase transformation into yield function. Thus derived constitutive equation is applied to describe strain response under varying temperature and stress with some discussions as well as metallo-thermo-mechanical simulation of quenching.


Sign in / Sign up

Export Citation Format

Share Document