Effective dispersion of aqueous clay suspension using carboxylated nanofibrillated cellulose as dispersant

The performance of dual coagulants in clay suspension was investigated in this study using aluminium chloride and the cationic polymer as coagulants. According to the study results, the performance of dual coagulants was affected by dosage of aluminium chloride. Beneficial effect by use of dual coagulants were only noted when aluminium chloride was underdosed. The addition sequence of coagulants was important for the performance of dual coagulants. Simultaneous addition resulted in the best performance, while addition of the polymer first resulted in the worst performance. Addition of aluminium chloride first resulted in the similar performance as single use of aluminium chloride. Although sulphate ion improved the floc characteristics, similar results were obtained. The effectiveness of rapid mixing depended on dosage of aluminium chloride. Extending rapid mixing (6 min) was beneficial when aluminium chloride was underdosed so that coagulation occurred at the combination region. However, such benefit was not observed at the optimum condition, which belonged to the sweep coagulation region. Different floc formation caused the difference. Extended rapid mixing would be beneficial when collision between clay particles and Al(III) was necessary. However, such benefit would disappear at the optimum condition because rapid mixing could break up the floc already formed.

Download Full-text

Application of a Simple Cold Stub to the Direct Observation of Frozen Hydrated Sand

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100071508 ◽

1973 ◽

Vol 31 ◽

pp. 212-213

Author(s):

John M. Wehrung ◽

Richard J. Harniman

Keyword(s):

United States ◽

Surface Water ◽

Direct Observation ◽

Controlled Study ◽

Clay Particles ◽

Organic Debris ◽

Rock Formations ◽

Water Tables ◽

Permeable Rock ◽

Natural Means

Water tables in aquifer regions of the southwest United States are dropping off at a rate which is greater than can be replaced by natural means. It is estimated that by 1985 wells will run dry in this region unless adequate artificial recharging can be accomplished. Recharging with surface water is limited by the plugging of permeable rock formations underground by clay particles and organic debris.A controlled study was initiated in which sand grains were used as the rock formation and water with known clay concentrations as the recharge media. The plugging mechanism was investigated by direct observation in the SEM of frozen hydrated sand samples from selected depths.

Download Full-text

Surface energy of cellulosic materials: The effect of particle morphology, particle size, and hydroxyl number

TAPPI Journal ◽

10.32964/tj14.9.565 ◽

2015 ◽

Vol 14 (9) ◽

pp. 565-576 ◽

Cited By ~ 1

Author(s):

YUCHENG PENG ◽

DOUGLAS J. GARDNER

Keyword(s):

Particle Size ◽

Surface Energy ◽

Particle Morphology ◽

Nanofibrillated Cellulose ◽

Particle Sizes ◽

Hydroxyl Number ◽

Small Individual ◽

Dispersion Component ◽

Commercial Applications ◽

Lower Temperature

Understanding the surface properties of cellulose materials is important for proper commercial applications. The effect of particle size, particle morphology, and hydroxyl number on the surface energy of three microcrystalline cellulose (MCC) preparations and one nanofibrillated cellulose (NFC) preparation were investigated using inverse gas chromatography at column temperatures ranging from 30ºC to 60ºC. The mean particle sizes for the three MCC samples and the NFC sample were 120.1, 62.3, 13.9, and 9.3 μm. The corresponding dispersion components of surface energy at 30°C were 55.7 ± 0.1, 59.7 ± 1.3, 71.7 ± 1.0, and 57.4 ± 0.3 mJ/m2. MCC samples are agglomerates of small individual cellulose particles. The different particle sizes and morphologies of the three MCC samples resulted in various hydroxyl numbers, which in turn affected their dispersion component of surface energy. Cellulose samples exhibiting a higher hydroxyl number have a higher dispersion component of surface energy. The dispersion component of surface energy of all the cellulose samples decreased linearly with increasing temperature. MCC samples with larger agglomerates had a lower temperature coefficient of dispersion component of surface energy.

Download Full-text

PEMANFAATAN KAYU AKASIA MANGIUM (Acacia mangium Willd) UNTUK MEBEL

Jurnal Riset Industri Hasil Hutan ◽

10.24111/jrihh.v4i1.1195 ◽

2012 ◽

Vol 4 (1) ◽

pp. 1

Author(s):

Djoko Purwanto

Keyword(s):

Mechanical Properties ◽

Compressive Strength ◽

Physical Properties ◽

Treatment Process ◽

Acacia Mangium ◽

Physical And Mechanical Properties ◽

Wood Fibers ◽

Test Parameters ◽

Mechanical And Physical Properties ◽

Scale Scores

Timber Acacia mangium (Acacia mangium, Willd) for Furniture. The study aims to determine the mechanical and physical properties and the decorative value (color and fiber) wood of acacia mangium with using finishing materials. This type of finishing material used is ultran lasur natural dof ,ultran lasur classic teak, aqua politur clear dof, aqua politur akasia dan aqua politur cherry. After finishing the wood is stored for 3 months. Test parameters were observed, namely, physical and mechanical properties of wood, adhesion of finishing materials, color and appearance of the fiber, and timber dimensions expansion. The results showed that the mechanical physical properties of acacia wood qualified SNI. 01-0608-89 about the physical and mechanical properties of wood for furniture, air dry the moisture content from 13.78 to 14.89%, flexural strength from 509.25 to 680.50 kg/cm2, and compressive strength parallel to fiber 342.1 - 412.9 kg/cm2. Finishing the treatment process using five types of finishing materials can increase the decorative value (color and fiber) wood. Before finishing the process of acacia mangium wood has the appearance of colors and fibers and less attractive (scale scores 2-3), after finishing acacia wood fibers have the appearance of colors and interesting and very interesting (scale 4-5).Keywords: mangium wood, mechanical properties, decorative value, finishing, furniture.

Download Full-text

Formulation and Evaluation of Chitosan-Polyaniline Nanocomposites for Controlled Release of Anticancer Drug Doxorubicin

International Journal of Drug Delivery Technology ◽

10.25258/ijddt.v8i2.13874 ◽

2018 ◽

Vol 8 (2) ◽

Author(s):

Dillip Kumar Behera ◽

Kampal Mishra ◽

Padmolochan Nayak

Keyword(s):

Tensile Strength ◽

Drug Release ◽

Nanocomposite Films ◽

Casting Method ◽

Sustained Drug Release ◽

In Vitro Drug Release ◽

Clay Particles ◽

Solution Casting Method ◽

Nanoclay Content

In this present work, chitosan (CS) crosslink with polyaniline (PANI) with montmorilonite (MMT) called as (CSPANI/MMT) and CS crosslink with PANI without MMT called as (CS-PANI) were prepared by employing the solution casting method. Further the formation of nanocomposites CS-PANI/MMT and CS-PANI were investigated using XRD, FTIR, SEM and tensile strength. Water uptake and swelling ratio of the CS-PANI and CS-PANI/MMT were found to decrease with increase in concentration of clay. Mechanical properties of the CS-PANI and CS-PANI/MMT were assessed in terms of tensile strength and extensibility using texture analyzer. Increase in tensile strength and reduction in extensibility was reported with increase in the nanoclay content. In vitro drug release study on CS-PANI and CS-PANI/MMT indicated pronounced sustained release of doxorubicin by the incorporation of clay particles in the CS polymer matrix. Overall CSPANI/MMT nanocomposite films exhibited improved mechanical and sustained drug release properties than CS-PANI.

Download Full-text