Enhanced strength and foamability of high-density polyethylene prepared by pressure-induced flow and low-temperature crosslinking

RSC Advances ◽  
2016 ◽  
Vol 6 (41) ◽  
pp. 34422-34427 ◽  
Author(s):  
Tairong Kuang ◽  
Feng Chen ◽  
Dajiong Fu ◽  
Lingqian Chang ◽  
Xiangfang Peng ◽  
...  
Keyword(s):  
Low Temperature ◽  
Mechanical Strength ◽  
High Density Polyethylene ◽  
High Performance ◽  
High Density ◽  
Induced Flow

We report a high-performance high-density polyethylene (HDPE) with significantly enhanced mechanical strength by means of pressure-induced flow (PIF) and low-temperature crosslinking treatment.

scholarly journals Structures and impact strength variation of chemically crosslinked high-density polyethylene: effect of crosslinking density

RSC Advances ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 6791-6797
Author(s):  
Yueqing Ren ◽  
Xiaojie Sun ◽  
Lanlan Chen ◽  
Yafei Li ◽  
Miaomiao Sun ◽  
...  
Keyword(s):  
Low Temperature ◽  
Impact Strength ◽  
High Density Polyethylene ◽  
Crosslinking Density ◽  
High Density ◽  
Strength Variation

Crosslinking significantly improves the toughness and impact strength of HDPE and extends its application, especially at low temperature.

Anisotropic-to-Isotropic Change in Lateral Force at the Surface of Single-Crystal Lamellae of High-Density Polyethylene during Low-Temperature Annealing

2004 ◽  
Vol 37 (13) ◽  
pp. 5115-5117 ◽  
Author(s):  
Yuji Ryousho ◽  
Sono Sasaki ◽  
Toshihiko Nagamura ◽  
Atsushi Takahara ◽  
Tisato Kajiyama
Keyword(s):  
Low Temperature ◽  
Single Crystal ◽  
High Density Polyethylene ◽  
Lateral Force ◽  
High Density ◽  
Low Temperature Annealing

Towards high-performance, low-cost quartz sensors with high-density, well-separated, vertically aligned ZnO nanowires by low-temperature, seed-less, single-step, double-sided growth

2013 ◽  
Vol 24 (35) ◽  
pp. 355503 ◽  
Author(s):  
Andrea Orsini ◽  
Pier Gianni Medaglia ◽  
David Scarpellini ◽  
Roberto Pizzoferrato ◽  
Christian Falconi
Keyword(s):  
Low Temperature ◽  
High Performance ◽  
Low Cost ◽  
Single Step ◽  
Zno Nanowires ◽  
High Density ◽  
Vertically Aligned

Effects of Geometrical Shapes of Wood Particles on the Mechanical and Water-Uptake Properties of the Resulting Wood/High Density Polyethylene Composites

2010 ◽  
Vol 113-116 ◽  
pp. 674-678
Author(s):  
Hai Gang Wang ◽  
Qing Wen Wang ◽  
Yan Jun Xie ◽  
Yong Ming Song
Keyword(s):  
Water Uptake ◽  
High Density Polyethylene ◽  
High Performance ◽  
Diameter Ratio ◽  
High Density ◽  
Waste Wood ◽  
Geometrical Shapes ◽  
Wood Particles ◽  
Different Shapes ◽  
Mechanical Strengths

Waste wood particles of different shapes were used to reinforce high density polyethylene (HDPE) to prepare high performance wood/plastic composites (WPC). The wood particles showed a needle-, flake-, strand-, and powder-shape, respectively. The mechanical and water-uptake properties of the composites manufactured using extrusion were tested. The wood needles/HDPE composites (WN-WPC) exhibited slightly higher mechanical strengths and lower density than the composites with the other shapes of wood particles. When the flake-, strand-, and powder-shaped wood particles were replaced by wood needles, the flexural, tensile and impact strengths were increased approximately by 4.24%, 7.61%, and 16.6% on average, respectively, and the density was decreased by about 7.34%. The length and width of WPC specimens changed little when soaked in water, with the thickening on the edge area only. WN-WPC performed the best waterproof stability. Based on the experimental results, the wood needles with lager length-to-diameter ratio would be the most suitable for producing high performance WPC.

scholarly journals FUEL GASES FROM WASTE HIGH DENSITY POLYETHYLENE (HDPE) VIA LOW TEMPERATURE CATALYTIC PYROLYSIS

2020 ◽  
Vol 3 (1) ◽  
pp. 20-30
Author(s):  
Nguamo Surma ◽  
◽  
Godwin Ijuo ◽  
Blessing Ogoh-Orch ◽  
◽  
...  
Keyword(s):  
Low Temperature ◽  
High Density Polyethylene ◽  
Catalytic Pyrolysis ◽  
High Density

Evaluation of mechanical performance and water absorption properties of modified sugarcane bagasse high-density polyethylene plastic bag green composites

2021 ◽  
pp. 096739112110490
Author(s):  
Ruey Shan Chen ◽  
Yao Hsing Chai ◽  
Ezutah Udoncy Olugu ◽  
Mohd Nazry Salleh ◽  
Sahrim Ahmad
Keyword(s):  
Mechanical Strength ◽  
Water Absorption ◽  
Sugarcane Bagasse ◽  
High Density Polyethylene ◽  
High Density ◽  
Potential Candidate ◽  
Green Composites ◽  
Absorption Properties ◽  
Fiber Modification ◽  
Blending Method

Enormous amounts of plastic wastes are generated worldwide and the approaches related to plastic recycling or reusing have become the research focus in the field of composite materials. In this study, green composites were prepared via melt-blending method using high-density polyethylene (HDPE) sourced from plastic bags as a matrix and sugarcane bagasse (SCB) fiber as reinforcing filler. The effects of fiber loading (5, 10 and 15 wt%) and fiber modification on the mechanical and dimensional stability (weight gain by water absorption) properties of the green composites were investigated. Results showed that the inclusion of SCB fiber into recycled HDPE matrix increased the composite stiffness but decreased the mechanical strength and resistance to water absorption. With the fiber modification through alkali treatment, the mechanical strength was remarkably improved, and the modulus and water absorption of the composites were found to be reduced. From the finding, it can be concluded that the prepared green composites free of coupling agent could add value to the plastic and agricultural wastes, and serve a potential candidate to replace some conventional petroleum-based composites.

Sign in / Sign up

Export Citation Format

Share Document