scholarly journals Structures and impact strength variation of chemically crosslinked high-density polyethylene: effect of crosslinking density

RSC Advances ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 6791-6797
Author(s):  
Yueqing Ren ◽  
Xiaojie Sun ◽  
Lanlan Chen ◽  
Yafei Li ◽  
Miaomiao Sun ◽  
...  
Keyword(s):  
Low Temperature ◽  
Impact Strength ◽  
High Density Polyethylene ◽  
Crosslinking Density ◽  
High Density ◽  
Strength Variation

Crosslinking significantly improves the toughness and impact strength of HDPE and extends its application, especially at low temperature.

Evaluation of the Aging Behavior of High Density Polyethylene in Thermal Oxidative Environment by Principal Component Analysis

2017 ◽  
Vol 727 ◽  
pp. 447-449 ◽  
Author(s):  
Jun Dai ◽  
Hua Yan ◽  
Jian Jian Yang ◽  
Jun Jun Guo
Keyword(s):  
Principal Component Analysis ◽  
Impact Strength ◽  
High Density Polyethylene ◽  
Tensile Modulus ◽  
Principal Component ◽  
Component Analysis ◽  
High Density ◽  
Aging Behavior ◽  
Data Set ◽  
The Impact

To evaluate the aging behavior of high density polyethylene (HDPE) under an artificial accelerated environment, principal component analysis (PCA) was used to establish a non-dimensional expression Z from a data set of multiple degradation parameters of HDPE. In this study, HDPE samples were exposed to the accelerated thermal oxidative environment for different time intervals up to 64 days. The results showed that the combined evaluating parameter Z was characterized by three-stage changes. The combined evaluating parameter Z increased quickly in the first 16 days of exposure and then leveled off. After 40 days, it began to increase again. Among the 10 degradation parameters, branching degree, carbonyl index and hydroxyl index are strongly associated. The tensile modulus is highly correlated with the impact strength. The tensile strength, tensile modulus and impact strength are negatively correlated with the crystallinity.

scholarly journals Low-Temperature Mechanical Properties of High-Density and Low-Density Polyethylene and Their Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1821
Author(s):  
Ildar I. Salakhov ◽  
Nadim M. Shaidullin ◽  
Anatoly E. Chalykh ◽  
Mikhail A. Matsko ◽  
Alexey V. Shapagin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Impact Strength ◽  
Relative Elongation ◽  
High Density ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Elongation At Break ◽  
Subzero Temperatures ◽  
Izod Impact

Low-temperature properties of high-density polyethylene (HDPE), low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE), and their blends were studied. The analyzed low-temperature mechanical properties involve the deformation resistance and impact strength characteristics. HDPE is a bimodal ethylene/1-hexene copolymer; LDPE is a branched ethylene homopolymer containing short-chain branches of different length; LLDPE is a binary ethylene/1-butene copolymer and an ethylene/1-butene/1-hexene terpolymer. The samples of copolymers and their blends were studied by gel permeation chromatography (GPC), differential scanning calorimetry (DSC), 13С NMR spectroscopy, and dynamic mechanical analysis (DMA) using testing machines equipped with a cryochamber. It is proposed that such parameters as “relative elongation at break at −45 °C” and “Izod impact strength at −40 °C” are used instead of the ductile-to-brittle transition temperature to assess frost resistance properties because these parameters are more sensitive to deformation and impact at subzero temperatures for HDPE. LLDPE is shown to exhibit higher relative elongation at break at −45 °C and Izod impact strength at −20 ÷ 60 °C compared to those of LDPE. LLDPE terpolymer added to HDPE (at a content ≥ 25 wt.%) simultaneously increases flow properties and improves tensile properties of the blend at −45 °C. Changes in low-temperature properties as a function of molecular weight, MWD, crystallinity, and branch content were determined for HDPE, LLDPE, and their blends. The DMA data prove the resulting dependences. The reported findings allow one to understand and predict mechanical properties in the HDPE–LLDPE systems at subzero temperatures.

Anisotropic-to-Isotropic Change in Lateral Force at the Surface of Single-Crystal Lamellae of High-Density Polyethylene during Low-Temperature Annealing

2004 ◽  
Vol 37 (13) ◽  
pp. 5115-5117 ◽  
Author(s):  
Yuji Ryousho ◽  
Sono Sasaki ◽  
Toshihiko Nagamura ◽  
Atsushi Takahara ◽  
Tisato Kajiyama
Keyword(s):  
Low Temperature ◽  
Single Crystal ◽  
High Density Polyethylene ◽  
Lateral Force ◽  
High Density ◽  
Low Temperature Annealing

Effect of particulate fillers on natural rubber/high-density polyethylene blends for roofing application

2020 ◽  
pp. 096739112093461
Author(s):  
WVWH Wickramaarachchi ◽  
S Walpalage ◽  
SM Egodage
Keyword(s):  
Impact Strength ◽  
Natural Rubber ◽  
High Density Polyethylene ◽  
Thermoplastic Elastomer ◽  
Cost Effective ◽  
Barium Sulphate ◽  
Filler Loading ◽  
High Density ◽  
Melt Mixing ◽  
Excellent Property

Blending of two or more polymers generates a new material, which is more cost-effective than a newly synthesised material. Blending-type thermoplastic elastomer (TPE) is produced by melt-mixing of a thermoplastic with a rubber. These blends have high demands associated with excellent property combinations of the parent materials. Particulate fillers are used in the rubber and plastic industry for property modification and cost reduction. In this work, six particulate fillers, namely, calcium carbonate, barium sulphate (BaSO4), kaolin, talc, Snobrite clay and dolomite were used to develop natural rubber (NR)/high-density polyethylene (HDPE) TPE blends, and the most suitable filler for roofing application was identified. A series of NR/HDPE 20/80 blends were prepared by varying filler loading from 10 phr to 30 phr at 10 phr intervals using a Plasticorder. Mechanical properties, such as tensile strength, hardness, impact strength and tear strength, and gel content of the blends were investigated. The addition of talc, dolomite and kaolin to NR/HDPE blend showed reduced impact strength, which is the most important property for a roofing application. The other three fillers showed improved impact strength at specific loadings. The blend with 30 phr of BaSO4 was identified as the best blend, as per the overall performance.

Sign in / Sign up

Export Citation Format

Share Document