scholarly journals Changes in shaft resistance and pore water pressures during heating of an energy foundation

2020 ◽  
Vol 205 ◽  
pp. 05022
Author(s):  
Michael B. Reiter ◽  
Lydia Kurtz ◽  
Mohammed M. Attala ◽  
Tugce Baser
Keyword(s):  
Hydraulic Conductivity ◽  
Pore Water ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Thermally Induced ◽  
Shaft Resistance ◽  
Pore Water Pressures ◽  
Energy Foundations ◽  
Surrounding Soil

This study focuses on the evolution of shaft resistance during operation of a geothermal energy foundation installed in a saturated glacial till layer. Energy foundations are a sustainable alternative to traditional space heating and cooling approaches for buildings. Despite efficient operational performance, there are still valid concerns regarding the effects of heating on the structural performance of foundations. To investigate the effect of heating at the soil-pile interface, four drilled shafts are utilized as energy foundations on the Urbana-Champaign campus of the University of Illinois and instrumented. Although the energy foundations are not yet operational, a theoretical investigation is possible to understand the effects of heating on the evolution of thermally induced pore water pressures and the shaft resistance of an energy foundation. A thermo-poroelastic numerical model is validated against an analytical solution, then is used to analyze the thermo-mechanical response of the soil-structure system under different conditions. The results indicate that the evolution of pore water pressure is affected by the rate of heating and the hydraulic conductivity of the surrounding soil, as expected. Higher pore water pressures are generated in the case of low hydraulic conductivity and higher rates of heating. Prior to the dissipation of excess pore pressures, the changes in shaft resistance are variable and influenced by the thermally-induced deformation of the foundation and the surrounding soil.

Infiltration characteristics of two instrumented residual soil slopes

2003 ◽  
Vol 40 (5) ◽  
pp. 1012-1032 ◽  
Author(s):  
Illias Tsaparas ◽  
Harianto Rahardjo ◽  
David G Toll ◽  
Eng-Choon Leong
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Field Measurements ◽  
Residual Soil ◽  
Rainfall Runoff ◽  
Rainfall Events ◽  
Pore Water Pressures ◽  
Soil Slopes ◽  
Pressure Changes

This paper presents the analysis of a 12 month long field study of the infiltration characteristics of two residual soil slopes in Singapore. The field measurements consist of rainfall data, runoff data of natural and simulated rainfall events, and pore-water pressure changes during infiltration at several depths and at several locations on the two slopes. The analysis of the field measurements identifies the total rainfall and the initial pore-water pressures within the two slopes as the controlling parameters for the changes in the pore-water pressures within the slopes during infiltration.Key words: infiltration, rainfall, runoff, pore-water pressure, field measurements.

Field measurement of anchor forces, ground temperatures, and pore-water pressures behind a retaining structure in northwestern Ontario

1992 ◽  
Vol 29 (1) ◽  
pp. 112-116
Author(s):  
K. D. Eigenbrod ◽  
J. P. Burak
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Retaining Wall ◽  
Field Measurements ◽  
Strain Gauges ◽  
Ground Temperatures ◽  
Northwestern Ontario ◽  
Pore Water Pressures ◽  
Load Increase

Anchor forces, ground temperatures, and piezometric pressures were measured at a retaining wall in northwestern Ontario over a period of 2 years. The anchor forces were measured with strain gauges attached in pairs directly to the anchor rods. This method appeared practical in the field for time periods of less than 2 years as long as the strain gauges were carefully protected against moisture. The anchor forces increased from an average of 5 kN initially up to values of 50 kN during the winter periods and dropped during the summer periods back to the same values measured initially. The anchor forces were largely independent of pore-water pressure variations behind the wall. Rapid drawdown conditions, however, which were experienced during the second summer, were reflected in a load increase that was equivalent to the associated unloading effect in front of the wall. The pore-water pressures behind the wall were not noticeably affected by rapid drawdown, possibly due to the restraining effect of the anchors and the high rigidity of the low sheet pile wall. Ground temperatures at or below the groundwater table never dropped below 0 °C thus restricting the depth of frost penetration. Key words : anchor loads, freezing pressure, retaining walls, pore-water pressures, ground temperatures, field measurements.

scholarly journals Mechanical response and pore pressure generation in granular filters subjected to uniaxial cyclic loading

2018 ◽  
Vol 55 (12) ◽  
pp. 1756-1768
Author(s):  
Jahanzaib Israr ◽  
Buddhima Indraratna
Keyword(s):  
Cyclic Loading ◽  
Pore Pressure ◽  
Pore Water ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Internal Erosion ◽  
Excess Pore Water Pressure ◽  
Excess Pore

This paper presents results from a series of piping tests carried out on a selected range of granular filters under static and cyclic loading conditions. The mechanical response of filters subjected to cyclic loading could be characterized in three distinct phases; namely, (I) pre-shakedown, (II) post-shakedown, and (III) post-critical (i.e., the occurrence of internal erosion). All the permanent geomechanical changes such, as erosion, permeability variations, and axial strain developments, took place during phases I and III, while the specimen response remained purely elastic during phase II. The post-critical occurrence of erosion incurred significant settlement that may not be tolerable for high-speed railway substructures. The analysis revealed that a cyclic load would induce excess pore-water pressure, which, in corroboration with steady seepage forces and agitation due to dynamic loading, could then cause internal erosion of fines from the specimens. The resulting excess pore pressure is a direct function of the axial strain due to cyclic densification, as well as the loading frequency and reduction in permeability. A model based on strain energy is proposed to quantify the excess pore-water pressure, and subsequently validated using current and existing test results from published studies.

scholarly journals Experiment Study of Lateral Unloading Stress Path and Excess Pore Water Pressure on Creep Behavior of Soft Soil

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Wei Huang ◽  
Kejun Wen ◽  
Dongsheng Li ◽  
Xiaojia Deng ◽  
Lin Li ◽  
...  
Keyword(s):  
Pore Water ◽  
Creep Behavior ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Stress Path ◽  
Deviatoric Stress ◽  
Excess Pore Water Pressure ◽  
Pore Water Pressures ◽  
Excess Pore

The unloading creep behavior of soft soil under lateral unloading stress path and excess pore water pressure is the core problem of time-dependent analysis of surrounding rock deformation under excavation of soft soil. The soft soil in Shenzhen, China, was selected in this study. The triaxial unloading creep tests of soft soil under different initial excess pore water pressures (0, 20, 40, and 60 kPa) were conducted with the K0 consolidation and lateral unloading stress paths. The results show that the unloading creep of soft soil was divided into three stages: attenuation creep, constant velocity creep, and accelerated creep. The duration of creep failure is approximately 5 to 30 mins. The unloading creep behavior of soft soil is significantly affected by the deviatoric stress and time. The nonlinearity of unloading creep of soft soil is gradually enhanced with the increase of the deviatoric stress and time. The initial excess pore water pressure has an obvious weakening effect on the unloading creep of soft soil. Under the same deviatoric stress, the unloading creep of soft soil is more significant with the increase of initial excess pore water pressure. Under undrained conditions, the excess pore water pressure generally decreases during the lateral unloading process and drops sharply at the moment of unloading creep damage. The pore water pressure coefficients during the unloading process were 0.73–1.16, 0.26–1.08, and 0.35–0.96, respectively, corresponding to the initial excess pore water pressures of 20, 40, and 60 kPa.

scholarly journals Influence of Soil Structure on the Mechanical Response of Soft Soil

2018 ◽  
Vol 38 ◽  
pp. 03027
Author(s):  
Bin Bin Xu
Keyword(s):  
Yield Stress ◽  
Pore Water ◽  
Soil Structure ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Before And After ◽  
Strain Relationship ◽  
Consolidation Behavior

Usually the natural sedimentary soils possess structure more or less, which makes their mechanical response much different from the fully remolded soils. In this paper, the influence of soil structure on the mechanical response such as compressibility, shear, permeability is literately reviewed. It is found that the compressibility and consolidation behavior of structured and remolded soils can be divided clearly before or after the structural yield stress. The stress-strain relationship can be divided into two segments before and after the structural yield stress. Before the yield stress, the curve is elevating and after the yield stress the curve is decreasing. The increasing rate of pore water pressure increases after the soil reached yield stress.

scholarly journals Response of sediment to ice-sheet loading in northwestern Germany: effective stresses and glacier-bed stability

1997 ◽  
Vol 43 (145) ◽  
pp. 495-502 ◽  
Author(s):  
Jan A. Piotrowski ◽  
Anna M. Kraus
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Ice Sheet ◽  
Bed Deformation ◽  
Pore Water Pressures ◽  
Sediment Consolidation ◽  
Western Germany ◽  
Bed Stability ◽  
North Western

AbstractLaboratory tests on sediment over-ridden by the last ice sheet in north-western Germany reveal very low ice-induced pre-consolidation and high palaeo-pore-water pressures. Sediment consolidation at the base of the glacier was largely controlled by hydraulic properties of the substratum. Generally low permeabilities of the bed caused sustained high pore-water pressure in over-ridden sediments close to the flotation point. This implies a serious possibility of hydraulic lifting of the ice sheet. It is believed that the reduced basal coupling limited the transformation of glacier shear stress on to the bed sediments, which is indicated by a lack of sedimentological evidence for widespread pervasive bed deformation. Ice motion was probably focused at the glacier sole by some combination of sliding and ploughing. However, isolated spots with deformation occur, so that the subglacial system in the study area can be characterized as a stable/deforming mosaic.

Modelling unanticipated pore-water pressures in soft clays

1994 ◽  
Vol 31 (5) ◽  
pp. 773-778 ◽  
Author(s):  
Jianhua Yin ◽  
James Graham ◽  
Jack I. Clark ◽  
Longjun Gao
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Creep Behaviour ◽  
Soft Clay ◽  
Field Observations ◽  
Soft Clays ◽  
Secondary Compression ◽  
Pore Water Pressures ◽  
Clay Layers

Field observations in thin soft clay layers may show pore-water pressures that increase for some time after the loading is applied. Reasons for these observations are not well understood. The paper shows how an elastic viscoplastic constitutive model incorporated into the consolidation equation can predict these pore-water pressure increases in soils that exhibit significant creep behaviour (or secondary compression). The phenomenon has been related to relaxation in regions of the profile from which drainage has not yet begun. Key words : clay, consolidation, creep, secondary compression, viscous, relaxation, pore-water pressure, elastic–plastic.

scholarly journals Influence of Layer Transition Zone on Rainfall-Induced Instability of Multilayered Slope

Lithosphere ◽  
2021 ◽  
Vol 2021 (Special 4) ◽  
Author(s):  
Zhi Dou ◽  
Yimin Liu ◽  
Xueyi Zhang ◽  
Yashan Wang ◽  
Zhou Chen ◽  
...  
Keyword(s):  
Hydraulic Conductivity ◽  
Transition Zone ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Layer Transition ◽  
Infiltration Process ◽  
Local Factor ◽  
The Stability ◽  
Different Thickness

Abstract Although numerous studies have been paid much attention to rainfall-induced instability of multilayered slopes, the interface between layers is generally considered to be “zero thickness”, and the layer transition zone between layers is neglected. In this study, the influence of the layer transition zone on the rainfall-induced instability of multilayered slope was investigated. A model was developed to simulate the rainfall infiltration process, the distribution of pore water pressure, and the stability of multilayered slope by coupling the unsaturated seepage model and the slope stability analysis method. Based on the analysis of the multilayered slopes with the different thickness ratios of the layer transition zone, a method for determining the critical thickness of the layer transition zone was proposed. The results showed that the layer transition zone had a significant influence on the stability of multilayered slope. It was found that the presence of the layer transition zone in the multilayered slope reduced the hydraulic conductivity of the slope and increased the rate of formation of transient saturated zone, which contributed to excess pore water pressure at the toe of the slope. The analysis of the local factor of safety (LFS) showed that when the thickness ratios of the layer transition zone were between 2.5% and 5%, the corresponding hydraulic conductivity of the slope decreased by 1%-2.5% and the maximum failure area of the slope during the rainfall was 25% of the slope. Our study highlighted the importance of the layer transition zone for the rainfall-induced instability of the multilayered slope.

scholarly journals Thermally induced pore water pressure of reconstituted London clay

2019 ◽  
Vol 92 ◽  
pp. 10003
Author(s):  
Sihua Chen ◽  
Lidija Zdravkovic ◽  
J. Antonio H. Carraro
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Effect Of Temperature ◽  
Low Carbon ◽  
Thermally Induced ◽  
Engineering Construction ◽  
Active Structures ◽  
Heating And Cooling ◽  
London Clay

Different forms of thermo-active structures have been proposed as a way of making use of the ground temperature to achieve renewable low-carbon heating and cooling in civil engineering construction. Such structures comprise piles, retaining walls or tunnel linings, and are used both as structural components and as conduits for utilising geothermal energy. In the scenario of the underground space in London, it is the thermo-active piles that have received most attention. However, little experimental evidence exists on the thermal behaviour of London clay to aid the design of thermo-active structures. This paper presents advanced laboratory testing on the reconstituted London clay to characterise the effect of temperature on its mechanical behaviour. Particular emphasis is given to thermally induced pore water pressures, as their evolution is not well understood. Tests are conducted in a temperature-controlled isotropic cell developed at Imperial College London. The emphasis of the current paper is on the temperature-based calibrations of different transducers. Soil specimens are isotropically consolidated and then subjected to undrained heating-cooling in the temperature range of 21 to 37 °C. Results obtained are compared with an existing laboratory study on another type of clay.

Sign in / Sign up

Export Citation Format

Share Document