scholarly journals Electrical Discharge Machining of SiC Reinforced 6061-T6 Aluminum Alloy Surface Composite Fabricated by Friction Stir Processing

2021 ◽  
Vol 309 ◽  
pp. 01044
Author(s):  
Murahari Kolli ◽  
Devaraju Aruri ◽  
Saikumar Gadakary ◽  
Satyanarayana Kosaraju
Keyword(s):  
Friction Stir Processing ◽  
Removal Rate ◽  
Alloy Surface ◽  
Aluminum Surface ◽  
Machining Parameters ◽  
Friction Stir ◽  
Surface Composite ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
The Impact

Engineered materials with high hardness, great wear tolerance, high high-temperature power, and a low thermal expansion coefficient are aluminum-based composites. These materials are widely used in the automotive and aerospace industries. Friction stir processing (FSP) method used to prepare SiC reinforced aluminium alloy surface composite. Material removal rate (MRR) and surface roughness (SR) are measured with the impact of pulse on time, discharge current, and pulse off time (add one or two outcomes remark at SR and MRR optimal condition) is examined. For each of the three machining parameters, L9 orthogonal arrays (OA) of three levels were used in conducting the experiments. The validity of the Aluminum Surface Composite experiment programme is determined using MINITAB.

Performance Analysis on Eco-friendly Machining of Ti6Al4V using Powder Mixed with Different Dielectrics in WEDM

2020 ◽  
Vol 17 (3) ◽  
pp. 8128-8139
Author(s):  
S. Chakraborty ◽  
S. Mitra ◽  
D. Bose
Keyword(s):  
Metal Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Process Efficiency ◽  
Machining Parameters ◽  
Dielectric Fluids ◽  
High Emission ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The recent scenario of modern manufacturing is tremendously improved in the sense of precision machining and abstaining from environmental pollution and hazard issues. In the present work, Ti6Al4V is machined through wire EDM (WEDM) process with powder mixed dielectric and analyzed the influence of input parameters and inherent hazard issues. WEDM has different parameters such as peak current, pulse on time, pulse off time, gap voltage, wire speed, wire tension and so on, as well as dielectrics with powder mixed. These are playing an essential role in WEDM performances to improve the process efficiency by developing the surface texture, microhardness, and metal removal rate. Even though the parameter’s influencing, the study of environmental effect in the WEDM process is very essential during the machining process due to the high emission of toxic vapour by the high discharge energy. In the present study, three different dielectric fluids were used, including deionised water, kerosene, and surfactant added deionised water and analysed the data by taking one factor at a time (OFAT) approach. From this study, it is established that dielectric types and powder significantly improve performances with proper set of machining parameters and find out the risk factor associated with the PMWEDM process.

Mathematical Modeling of Machining Parameters in Electrical Discharge Machining with Cu-B4C Composite Electrode

2012 ◽  
Vol 488-489 ◽  
pp. 871-875
Author(s):  
V. Anandakrishnan ◽  
V. Senthilkumar
Keyword(s):  
Mathematical Models ◽  
Current Pulse ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Selection Of

Copper based metal matrix composite reinforced with Boron Carbide is a newly developed Electrical Discharge Machining (EDM) electrode showing better performance than the conventional copper based electrode. Right selection of machining parameters such as current, pulse on time and pulse off time is one of the most important aspects in EDM. In this paper an attempt has been made to develop mathematical models for relating the Material Removal Rate (MRR), Tool Removal Rate (TRR) and Surface roughness (Ra) to machining parameters (current, pulse-on time and pulse-off time). Furthermore, a study was carried out to analyze thSubscript texte effects of machining parameters on various performance parameters such as, MRR, TRR and Ra. The results of Analysis of Variance (ANOVA) indicate that the proposed mathematical models, can adequately describe the performance within the limits of the factors being studied. Response surface modeling is used to develop surface and contour graphs to analyze the effects of EDM input parameters on outer parameters.

Nano Graphite Powder Assisted Electric Discharge Machining Characteristics of ZM21 Magnesium Alloy

2015 ◽  
Vol 787 ◽  
pp. 406-410
Author(s):  
S. Santosh ◽  
S. Javed Syed Ibrahim ◽  
P. Saravanamuthukumar ◽  
K. Rajkumar ◽  
K.L. Hari Krishna
Keyword(s):  
Magnesium Alloy ◽  
Material Removal Rate ◽  
Electric Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Parameters ◽  
Electric Discharge Machining ◽  
Zm21 Magnesium Alloy ◽  
Pulse On Time ◽  
Pulse Off Time

Magnesium alloys are used in many applications, particularly in orthopaedic implants are very difficult to machine by conventional processes because of their complex 3D structure and limited slip system at room temperature. Hence there is an inherent need for alternative processes for machining such intricate profiles. Electric Discharge Machining is growing rapidly in tool rooms, die shops and even in general shop floors of modern industries to facilitate complex machining for difficult-to-machine materials and provide better surface integrity. Therefore, the use of electric discharge machining on ZM21 magnesium alloy is attempted in this paper. Nanographite powder is added for machining zone to enhance the electrical conductivity of EDM oil by way it improves the machining performance. Machining parameters such as the current, pulse on time and pulse off time were process parameters to explore their effects on the material removal rate and tool wear rate. It is observed that, an increased material removal rate was due to the enhanced electrical and thermal conductivity of the EDM oil.

Electrical Discharge Machining of SiC and Gr Reinforced 6061-T6 Aluminum Alloy Hybrid Composite Fabricated by Friction Stir Processing

2013 ◽  
Author(s):  
Murahari Kolli ◽  
Devaraj Aruri ◽  
Kumar Adepu
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Processing ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Hybrid Composites ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Machining Parameters ◽  
Machining Performance ◽  
Friction Stir

Aluminum based hybrid composites are advanced materials having the properties of high hardness, superior wear resistance, strength, high elevated temperature and low thermal expansion coefficient. These hybrid composites are widely used in industries like automobile and aerospace. In this present paper 6061-T6 Aluminum alloy reinforced with SiC and Gr particles, hybrid composites are fabricated by using Friction stir processing (FSP) technique. It prevents the further development of hybrid composites for machining by nonconventional methods like water jet and laser cutting process. Electrical discharge machining (EDM) is used for machining the complex shapes of the material. This paper presents an overview of EDM studies conducted on the Al-SiC/Gr hybrid composites using a copper electrode in EDM. The EDM experiment machining parameters such as the dielectric fluid, peak current, pulse on, pulse off times are changed to explore their effects on machining performance, material removal rate (MRR), Tool wear rate (TWR), and surface roughness (SR). It is observed that the MRR and SR of the Al-SiC/Gr hybrid composites increase with an increase in the current.

Optimization of WEDM Process Parameters

2014 ◽  
Vol 592-594 ◽  
pp. 831-835 ◽  
Author(s):  
Vikram Singh ◽  
Sharad Kumar Pradhan
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The objective of the present work is to investigate the effects of various WEDM process parameters like pulse on time, pulse off time, corner servo, flushing pressure, wire feed rate, wire tension, spark gap voltage and servo feed on the material removal rate (MRR) & Surface Roughness (SR) and to obtain the optimal settings of machining parameters at which the material removal rate (MRR) is maximum and the Surface Roughness (SR) is minimum in a range. In the present investigation, Inconel 825 specimen is machined by using brass wire as electrode and the response surface methodology (RSM) is for modeling a second-order response surface to estimate the optimum machining condition to produce the best possible response within the experimental constraints.

scholarly journals Comparative Study on EDM of Ti-6Al-4V Using Circular and Convex Shaped Electrodes

2018 ◽  
Vol 7 (3.34) ◽  
pp. 256
Author(s):  
S Rajamanickam ◽  
R Palani ◽  
V Sathyamoorthy ◽  
Muppala Jagadeesh Varma ◽  
Shaik Shaik Mahammad Althaf ◽  
...  
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Industrial Applications ◽  
Copper Electrode ◽  
Machining Process ◽  
Project Work ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time

As on today, Electrical Discharge Machining (EDM) is world famous unconventional machining process for electrically conductive materials. In this project work, Ti-6Al-4V is performed in electrical discharge machining using differently shaped (circular and convex) copper electrode. The machining parameters considered are the pulse on- time, pulse off-time, voltage and current to investigate machining characteristics like material removal rate and tool wear rate. Taguchi method is applied to frame experimental design. Ti-6Al-4V finds wide usage in industrial applications such as marine, aerospace, bio-medical and so on. 

The Effect of EDM Die-Sinking Parameters on Machining Characteristics in Aluminum Alloy Machining

2015 ◽  
Vol 761 ◽  
pp. 303-307 ◽  
Author(s):  
Laily Suraya ◽  
M.A. Ali ◽  
N.I.S. Hussein ◽  
Mohd Razali Muhamad ◽  
Manshoor Bukhari ◽  
...  
Keyword(s):  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Design Matrix ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Electrode Tool ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Machining Characteristics

The effect of machining parameters on machining characteristics for aluminium alloy LM6 (Al-Sil2) in Electrical Discharge Machining (EDM) die-sinking is studied. The objective of this project is to determine the relationship between the machining parameters including pulse-on time, pulse-off time, peak current and voltage with the machining characterictics such as Material Removal Rate (MRR), Electrode Wear Rate (EWR) and Surface Roughness (Ra). Copper materials having diameter 15mm was chosen as the electrode tool. Design of experimenent using Taguchi technique was employed to design experimental matrix that was used to optimize the MRR, EWR and Ra. The analysis was done by using the Minitab software version 16. It is found that current and pulse off time significantly affect MRR, EWR and Ra while pulse on time and voltage are less significant in their effect on machining responses. Results show that using Taguchi as a design matrix, the best setting of optimum value for machining parameters to find the required machining responses can be obtained.

Performance Measurement and Data Analysis of Material Removal Rate for Wire Cut Electro Discharge Machining Process

2011 ◽  
Vol 110-116 ◽  
pp. 1683-1690 ◽  
Author(s):  
Vishal Parashar ◽  
A. Rehman ◽  
J.L. Bhagoria
Keyword(s):  
Regression Analysis ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Performance Criteria ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Dielectric Flushing

In this paper, statistical and regression analysis of material removal rate using design of experiments is proposed for WEDM operations. Experimentation was planned as per Taguchi’s mixed orthogonal array. Each experiment has been performed under different cutting conditions of gap voltage, pulse ON time, pulse OFF time, wire feed and dielectric flushing pressure. Stainless Steel grade 304L was selected as a work material to conduct the experiments. From experimental results, the material removal rate was determined for each machining performance criteria. Analysis of variance (ANOVA) technique was used to find out the variables affecting the material removal rate. Assumptions of ANOVA were discussed and carefully examined using analysis of residuals. Variation of the material removal rate with machining parameters was mathematically modeled by using the regression analysis method. The developed model was validated with a set of experimental data and appeared to be satisfactory. Signal to noise ratio was applied to measure the performance characteristics deviating from the actual value. Finally, experimental confirmation was carried out to identify the effectiveness of this proposed method.

Influence of ceramic Al2O3 particulates on performance measures and surface characteristics during sinker EDM of stir cast AMMCs

2019 ◽  
Vol 16 (4) ◽  
pp. 526-538 ◽  
Author(s):  
Akhil Khajuria ◽  
Modassir Akhtar ◽  
Manish Kumar Pandey ◽  
Mayur Pratap Singh ◽  
Ankush Raina ◽  
...  
Keyword(s):  
Performance Measures ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Base Material ◽  
Machining Parameters ◽  
Content Type ◽  
Weight Percentage ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

Purpose AA2014 is a copper-based alloy and is typically used for production of complex machined components, given its better machinability. The purpose of this paper was to study the effects of variation in weight percentage of ceramic Al2O3 particulates during electrical discharge machining (EDM) of stir cast AA2014 composites. Scanning electron microscopy (SEM) examination was carried out to study characteristics of EDMed surface of Al2O3/AA2014 composites. Design/methodology/approach The effect of machining parameters on performance measures during sinker EDM of stir cast Al2O3/AA2014 composites was examined by “one factor at a time” (OFAT) method. The stir cast samples were obtained by using three levels of weight percentage of Al2O3 particulates, i.e. 0 Wt.%, 10 Wt.% and 20 Wt.% with density 1.87 g/cc, 2.35 g/cc and 2.98 g/cc respectively. Machining parameters varied were peak current (1-30 amp), discharge voltage (30-100 V), pulse on time (15-300 µs) and pulse off time (15-450 µs) to study their influence on material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR). Findings MRR and SR decreased with an increase in weight percentage of ceramic Al2O3 particulates at the expense of TWR. This was attributed to increased microhardness for reinforced stir cast composites. However, microhardness of EDMed samples at fixed values of machining parameters, i.e. 9 amp current, 60 V voltage, 90 µs pulse off time and 90 µs pulse on time reduced by 58.34, 52.25 and 46.85 per cent for stir cast AA2014, 10 Wt.% Al2O3/AA2014 and 20 Wt.% Al2O3/AA2014, respectively. SEM and quantitative energy dispersive spectroscopy (EDS) analysis revealed ceramic Al2O3 particulate thermal spalling in 20 Wt.% Al2O3/AA2014 composite. This was because of increased particulate weight percentage leading to steep temperature gradients in between layers of base material and heat affected zone. Originality/value This work was an essential step to assess the machinability for material design of Al2O3 reinforced aluminium metal matrix composites (AMMCs). Experimental investigation on sinker EDM of high weight fraction of particulates in AA2014, i.e. 10 Wt.% Al2O3 and 20 Wt.% Al2O3, has not been reported in archival literature. The AMMCs were EDMed at variable peak currents, voltages, pulse on and pulse off times. The effects of process parameters on MRR, TWR and SR were analysed with comparisons made to show the effect of Al2O3 particulate contents.

Experimental Analysis of Machining Parameters in WEDM of AISI D3 Steel Using Taguchi Method

2015 ◽  
Vol 799-800 ◽  
pp. 343-350
Author(s):  
Rahul Shukla ◽  
Brajesh Kumar Lodhi
Keyword(s):  
Taguchi Method ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Parameters ◽  
Kerf Width ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

Wire Electric Discharge Machining (WEDM) is a non-traditional process of material from conductive material to produce parts with intricate shape and profiles. In the present work, an attempt has been made to optimization the machining conditions for maximum material removal rate, minimise kerf width based on (L9 Orthogonal Array) Taguchi method. Experiments, based on Taguchi’s parameters design, were carried out to effect of machining parameters, like pulse-on-time (TON), pulse-off-time (TOFF), peak current (IP), and wire feed (WF) on the material removal rate and kerf width. The importance of the cutting parameters on the cutting performance outputs is determined by using the variance analysis (ANOVA). The variation of MRR and kerf width with cutting parameters is modeled by using a regression analysis method.

Sign in / Sign up

Export Citation Format

Share Document