scholarly journals Dynamics of the nozzle valve with regard to the properties of the piping system

2018 ◽  
Vol 180 ◽  
pp. 02043
Author(s):  
Roman Klas ◽  
Vladimír Habán ◽  
Pavel Rudolf
Keyword(s):  
Dynamic Properties ◽  
Equations Of Motion ◽  
Operating Conditions ◽  
Pipeline System ◽  
Piping System ◽  
Main Function ◽  
Pressure Pulsations ◽  
Cfd Simulations ◽  
Valve Disc ◽  
Pipeline Model

It is obvious that the main function of the nozzle valve is to shut off the stream of fluid in the piping system. The response rate of the valve to the decreasing or reversing flow in the system will then depend on the valve properties and equally on the properties of the piping system. The interaction of these two elements is also important for the origin of pressure pulsations in the system. While the pressure pulsations were the cause for design of this particular valve it should be noted that the general design of the valve for any pipeline system is not possible. The valve cannot properly work under all circumstances and operating conditions. With respect to this, the dynamic properties of the valve will be assessed on the basis of the valve equation of motion and the pipeline model. An adequate response of the whole system can be obtained by combining both approaches. The valve equations of motion are also complemented by CFD simulations, which enable to capture the movement of the valve disc with respect to flow rate.

Dynamic Response of a Piping System Under Harmonic Excitations Considering Pipe-Support Friction With Variable Normal Loads

2013 ◽  
Author(s):  
José Argüelles ◽  
Euro Casanova
Keyword(s):  
Equations Of Motion ◽  
Numerical Approach ◽  
Operating Conditions ◽  
Dynamic Loads ◽  
Computational Time ◽  
Integration Scheme ◽  
Piping System ◽  
Harmonic Excitations ◽  
Piping Systems ◽  
Support Surfaces

Dynamic loads in piping systems are mainly caused by transient phenomena generated by operating conditions or installed equipment. In most cases these dynamic loads may be modeled as harmonic excitations e.g. pulsating flow. On the other hand, when designing piping systems under dynamic loads, it’s a common practice to neglect strong nonlinearities such as shocks and friction between pipe and support surfaces, mainly because of the excessive cost in terms of computational time and the complexity associated with the integration of the nonlinear equations of motion. However, disregarding these nonlinearities for some systems may result in overestimated dynamic amplitudes leading to incorrect analysis and designs. This paper presents a numerical approach to calculate the steady-state response amplitudes of a piping system subject to harmonic excitations and considering dry friction between the pipe and the support surfaces, without performing a numerical integration. The proposed approach permits the analysis of three dimensional piping systems where the normal forces may vary in time and is based in the Hybrid Frequency-Time Domain method (HFT). Results of the proposed approach are compared and discussed with those of a full integration scheme, confirming that HFT is a valid and computationally feasible option.

The Numerical and Experimental Investigation Into Hydraulic Characteristics of a No-Load Running Check Valve due to Fluid-Structure Interaction

2018 ◽  
Author(s):  
Xiang-yuan Zhang ◽  
Zhi-jun Shuai ◽  
Chen-xing Jiang ◽  
Wan-you Li ◽  
Jie Jian
Keyword(s):  
Flow Rate ◽  
Ambient Pressure ◽  
Check Valve ◽  
Operating Conditions ◽  
Flow Coefficient ◽  
Pipeline System ◽  
Piping System ◽  
Hydraulic Characteristics ◽  
Mass System ◽  
Excited Vibration

Valve is a very important unit in pipeline system. The valve flow fluctuation brings about structural vibration and unpopular noise, and even leads to the safety problems and disasters. In this paper, a special no-load running check valve is investigated. The check valve is structural complex with one inlet and two outlets. It can be simplified as a spring-mass system which manipulates the flow rate by combine action of the ambient pressure of medium and the spring deformation. The three-dimensional model of the valve is established and also the relationship between pressure drops and flow rate of the valve is obtained in various openings and operating conditions. The structure modals were verified by the field tests and thus its fixing boundaries are obtained correctly. The mechanism causing self-excited vibration of a piping system is determined using a dynamic model which couples the hydraulics of internal flow with the structural motion of a three-ports passive check valve. The coupling is obtained by making the fluid flow coefficient at the check valve to be a function of valve plug displacement. The results are compared with the experimental data, which verifies the correctness of the theoretical results. It is shown that the special valve has its own hydraulic characteristics, which greatly influence its flow distribution as it has two outlets. It was also testified that the coupling between fluid and structure changes its natural frequencies and has a non-negligible impact on the pressure fluctuation while working.

Optimized control over modes of hydraulic percussion cutting heads of mining machines

2020 ◽  
pp. 95-104
Author(s):  
Yu. M. Smirnov ◽  
B. M. Kenzhin ◽  
N. S. Smakova ◽  
M. A. Zhurunova
Keyword(s):  
Time Derivative ◽  
Operating Conditions ◽  
Control Action ◽  
Main Function ◽  
Output Data ◽  
Working Cycle ◽  
Control Units ◽  
Action Change ◽  
Function Element ◽  
Service Factors

The main cause of the disagreement between the actual and calculated output data of hydraulic percussion mining machines is the erroneous feed of manipulation signals by the control units. For the maximal fitting of the calculated and actual figures, the continuous method of control action using the third time derivative of the law of motion of the main function element is accepted, namely, the accuracy. The mathematical models of control using displacement, velocity and acceleration are developed. The service factors of mining machines are found. Based on the theory of control and the mathematical logic theory, the logical circuits of formation of manipulation signals in each phase of the working cycle are developed. The main elements are converters, integrators and accumulators ensuring decomposition of elements of the logical circuits and further generation of appropriate control action. It is found that the simplest way is to generate the control action for acceleration of the key function element. For the developed circuits, it is recommended to use general charts of the control action change, implementable for a certain design of hydraulic percussion cutting heads in certain operating conditions.

scholarly journals Aerodynamic Analysis of Multistage Turbomachinery Flows in Support of Aerodynamic Design

1999 ◽  
Author(s):  
John J. Adamczyk
Keyword(s):  
Unsteady Flow ◽  
Axial Flow ◽  
Operating Conditions ◽  
Design Environment ◽  
Cfd Simulations ◽  
Average Flow ◽  
Flow Models ◽  
Time Average ◽  
Semi Empirical ◽  
Future Work

This paper summarizes the state of 3D CFD based models of the time average flow field within axial flow multistage turbomachines. Emphasis is placed on models which are compatible with the industrial design environment and those models which offer the potential of providing credible results at both design and off-design operating conditions. The need to develop models which are free of aerodynamic input from semi-empirical design systems is stressed. The accuracy of such models is shown to be dependent upon their ability to account for the unsteady flow environment in multistage turbomachinery. The relevant flow physics associated with some of the unsteady flow processes present in axial flow multistage machinery are presented along with procedures which can be used to account for them in 3D CFD simulations. Sample results are presented for both axial flow compressors and axial flow turbines which help to illustrate the enhanced predictive capabilities afforded by including these procedures in 3D CFD simulations. Finally, suggestions are given for future work on the development of time average flow models.

scholarly journals Inner Damping of Water in Conduit of Hydraulic Power Plant

2021 ◽  
Vol 13 (13) ◽  
pp. 7125
Author(s):  
Daniel Himr ◽  
Vladimír Habán ◽  
David Štefan
Keyword(s):  
Power Plant ◽  
Operating Conditions ◽  
Mathematical Apparatus ◽  
Pressure Pulsations ◽  
Hydraulic Power ◽  
Economic Operation ◽  
Compression And Expansion ◽  
Rotor Stator Interaction ◽  
Start Ups

The operation of any hydraulic power plant is accompanied by pressure pulsations that are caused by vortex rope under the runner, rotor–stator interaction and various transitions during changes in operating conditions or start-ups and shut-downs. Water in the conduit undergoes volumetric changes due to these pulsations. Compression and expansion of the water are among the mechanisms by which energy is dissipated in the system, and this corresponds to the second viscosity of water. The better our knowledge of energy dissipation, the greater the possibility of a safer and more economic operation of the hydraulic power plant. This paper focuses on the determination of the second viscosity of water in a conduit. The mathematical apparatus, which is described in the article, is applied to data obtained during commissioning tests in a water storage power plant. The second viscosity is determined using measurements of pressure pulsations in the conduit induced with a ball valve. The result shows a dependency of second viscosity on the frequency of pulsations.

Managing Flow Induced Vibration in Subsea Jumpers

2021 ◽  
Author(s):  
Rakshith Naik ◽  
Yetzirah Urthaler ◽  
Scot McNeill ◽  
Rafik Boubenider
Keyword(s):  
Dynamic Properties ◽  
Fatigue Analysis ◽  
Management Program ◽  
Measured Data ◽  
Operating Conditions ◽  
Valuable Insight ◽  
Fe Model ◽  
Flow Induced Vibration ◽  
Vibration Measurements

Abstract Certain subsea jumper design features coupled with operating conditions can lead to Flow Induced Vibration (FIV) of subsea jumpers. Excessive FIV can result in accumulation of allowable fatigue damage prior to the end of jumper service life. For this reason, an extensive FIV management program was instated for a large development in the Gulf of Mexico (GOM) where FIV had been observed. The program consisted of in-situ measurement, modeling and analysis. Selected well and flowline jumpers were outfitted with subsea instrumentation for dedicated vibration testing. Finite Element (FE) models were developed for each jumper and refined to match the dynamic properties extracted from the measured data. Fatigue analysis was then carried out using the refined FE model and measured response data. If warranted by the analysis results, action was taken to mitigate the deleterious effects of FIV. Details on modeling and data analysis were published in [5]. Herein, we focus on the overall findings and lessons learned over the duration of the program. The following topics from the program are discussed in detail: 1. In-situ vibration measurement 2. Overall vibration trends with flow rate and lack of correlation of FIV to flow intensity (rho-v-squared); 3. Vibration and fatigue performance of flowline jumpers vs. well jumpers 4. Fatigue analysis conservatism Reliance on screening calculations or predictive FE analysis could lead to overly conservative operational limits or a high degree of fatigue life uncertainty in conditions vulnerable to FIV. It is proposed that in-situ vibration measurements followed by analysis of the measured data in alignment with operating conditions is the best practice to obtain a realistic understanding of subsea jumper integrity to ensure safe and reliable operation of the subsea system. The findings from the FIV management program provide valuable insight for the subsea industry, particularly in the areas of integrity management of in-service subsea jumpers; in-situ instrumentation and vibration measurements and limitations associated with predictive analysis of jumper FIV. If learnings, such as those discussed here, are fed back into design, analysis and monitoring guidelines for subsea equipment, the understanding and management of FIV could be dramatically enhanced compared to the current industry practice.

Some Nonlinear Effects of Magnetic Bearings

1999 ◽  
Author(s):  
Norbert Steinschaden ◽  
Helmut Springer
Keyword(s):  
Equations Of Motion ◽  
Period Doubling ◽  
Path Following ◽  
Nonlinear Effects ◽  
Magnetic Bearing ◽  
Operating Conditions ◽  
Active Magnetic Bearing ◽  
Nonlinear Phenomena ◽  
Amb System ◽  
Large Rotor

Abstract In order to get a better understanding of the dynamics of active magnetic bearing (AMB) systems under extreme operating conditions a simple, nonlinear model for a radial AMB system is investigated. Instead of the common way of linearizing the magnetic forces at the center position of the rotor with respect to rotor displacement and coil current, the fully nonlinear force to displacement and the force to current characteristics are used. The AMB system is excited by unbalance forces of the rotor. Especially for the case of large rotor eccentricities, causing large rotor displacements, the behaviour of the system is discussed. A path-following analysis of the equations of motion shows that for some combinations of parameters well-known nonlinear phenomena may occur, as, for example, symmetry breaking, period doubling and even regions of global instability can be observed.

Effects of Valve Disc on Flow Characteristics Inside a Swing Check Valve During Opening and Closing Processes

2021 ◽  
Author(s):  
Yi-xiang Xu ◽  
Qiang Ru ◽  
Huai-yu Yao ◽  
Zhi-jiang Jin ◽  
Jin-yuan Qian
Keyword(s):  
Flow Field ◽  
Working Conditions ◽  
Power Plants ◽  
Flow Characteristics ◽  
Check Valve ◽  
Opening Angle ◽  
Piping System ◽  
Total Moment ◽  
Valve Disc ◽  
Opening And Closing

Abstract The check valve is one of the most important devices for safety protection of the piping system in thermal and nuclear power plants. As the key component of the check valve, the valve disc accounts for a major effect on the flow characteristics especially during the opening and closing processes. In this paper, a typical swing check valve is taken as the research object. In order to make a comparative study, three working conditions of 30% THA (Turbine Heat Acceptance), 50% THA and 100% THA are selected. Focusing on the effects of valve disc, how does the valve disc motion interact with the flow field around the valve disc is analyzed with the help of the dynamic mesh technology. The results show that under the combined action of fluid force and gravity, the check valve can be opened and closed quickly. During the opening process, the maximum total moment of the disc appears between 45° ∼ 50° opening angle, and during the closing process the maximum total moment occurs when the disc fully closed. The flow field near the valve disc has similar variation rules with the rotation of the valve disc in the three working conditions, and the pressure near the valve disc reaches the maximum value at the moment of opening and closing. This study can provide some suggestions for the further optimal design of similar swing check valve.

Attenuation of pulsations in the reciprocating compressor piping system with an elbow-shaped surge tank

2018 ◽  
Vol 233 (5) ◽  
pp. 1677-1689
Author(s):  
Quyang Ma ◽  
Guoan Yang ◽  
Mengjun Li
Keyword(s):  
Mathematical Model ◽  
Theoretical Analysis ◽  
Frequency Analysis ◽  
Transfer Matrix Method ◽  
Piping System ◽  
Pulsation Frequency ◽  
Reciprocating Compressor ◽  
Pressure Pulsations ◽  
Surge Tank ◽  
The Mathematical Model

An elbow-shaped surge tank is proposed to suppress the pressure pulsations. The transfer matrix method was developed and the mathematical model was established to predict the distribution of pressure pulsations in the piping system (on which a surge tank was already installed) with an elbow-shaped surge tank. Simulation work of the whole piping system was performed. The results show that the elbow-shaped surge tank has good performance to attenuate the pressure pulsations. The frequency analysis shows that the amplitude for the first pulsation frequency is attenuated to a low level. The impulse response was analyzed to examine the efficiency of suppressing pulsations by using the suppressor. The theoretical analysis showed that there exists the optimal suppression performance when setting the distance between the elbow-shaped surge tank and the existing one. Meanwhile, modifying the ratio of length to diameter with a fixed surge volume could also impact the pressure pulsations. The analysis results can be used as a reference in designing and installing the elbow-shaped surge tank.

Analysis of Pressure Pulsations in Reciprocating Compressor Piping Systems

1966 ◽  
Vol 88 (2) ◽  
pp. 164-168 ◽  
Author(s):  
S. S. Grover
Keyword(s):  
Field Test ◽  
Test Data ◽  
Piping System ◽  
Reciprocating Compressor ◽  
Practical Application ◽  
Pressure Pulsations ◽  
System A ◽  
Piping Systems ◽  
Limiting Condition

This paper deals with pulsations in pressure and flow in the reciprocating compressor and connected piping system. A model is presented that describes the excitation at the compressor and the propagation of the pulsations in the interconnected piping. It has been adapted to digital computations to predict the pulse magnitudes in reciprocating compressor piping systems and to assess measures for their control. Predicted results have been compared with field test data and with simplified limiting condition results. A discussion of its practical application is included.

Sign in / Sign up

Export Citation Format

Share Document