The influence of high temperature plastic deformation on the kinetics of graphitization of pyrolytic carbons

1969 ◽  
Vol 66 ◽  
pp. 121-128 ◽  
Author(s):  
D. B. Fischbach
Keyword(s):  
Plastic Deformation ◽  
High Temperature ◽  
Kinetics Of

The Ordered Phase Formation in Ti-Al-Ga Alloys

1970 ◽  
Vol 28 ◽  
pp. 440-441
Author(s):  
Shiro Fujishiro ◽  
Harold L. Gegel
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Titanium Alloys ◽  
Growth Kinetics ◽  
Stoichiometric Composition ◽  
Good Potential ◽  
Alpha Titanium ◽  
Cold Rolled ◽  
Kinetics Of ◽  
Thermal Stability Of

Ordered-alpha titanium alloys having a DO19 type structure have good potential for high temperature (600°C) applications, due to the thermal stability of the ordered phase and the inherent resistance to recrystallization of these alloys. Five different Ti-Al-Ga alloys consisting of equal atomic percents of aluminum and gallium solute additions up to the stoichiometric composition, Ti3(Al, Ga), were used to study the growth kinetics of the ordered phase and the nature of its interface.The alloys were homogenized in the beta region in a vacuum of about 5×10-7 torr, furnace cooled; reheated in air to 50°C below the alpha transus for hot working. The alloys were subsequently acid cleaned, annealed in vacuo, and cold rolled to about. 050 inch prior to additional homogenization

scholarly journals Structural Transformations and Mechanical Properties of Metastable Austenitic Steel under High Temperature Thermomechanical Treatment

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 645
Author(s):  
Igor Litovchenko ◽  
Sergey Akkuzin ◽  
Nadezhda Polekhina ◽  
Kseniya Almaeva ◽  
Evgeny Moskvichev
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Temperature ◽  
Austenitic Steel ◽  
Structural Transformations ◽  
Initial State ◽  
Twin Boundaries ◽  
Metastable Austenitic Steel ◽  
Average Grain Size ◽  
Heating Up

The effect of high-temperature thermomechanical treatment on the structural transformations and mechanical properties of metastable austenitic steel of the AISI 321 type is investigated. The features of the grain and defect microstructure of steel were studied by scanning electron microscopy with electron back-scatter diffraction (SEM EBSD) and transmission electron microscopy (TEM). It is shown that in the initial state after solution treatment the average grain size is 18 μm. A high (≈50%) fraction of twin boundaries (annealing twins) was found. In the course of hot (with heating up to 1100 °C) plastic deformation by rolling to moderate strain (e = 1.6, where e is true strain) the grain structure undergoes fragmentation, which gives rise to grain refining (the average grain size is 8 μm). Partial recovery and recrystallization also occur. The fraction of low-angle misorientation boundaries increases up to ≈46%, and that of twin boundaries decreases to ≈25%, compared to the initial state. The yield strength after this treatment reaches up to 477 MPa with elongation-to-failure of 26%. The combination of plastic deformation with heating up to 1100 °C (e = 0.8) and subsequent deformation with heating up to 600 °C (e = 0.7) reduces the average grain size to 1.4 μm and forms submicrocrystalline fragments. The fraction of low-angle misorientation boundaries is ≈60%, and that of twin boundaries is ≈3%. The structural states formed after this treatment provide an increase in the strength properties of steel (yield strength reaches up to 677 MPa) with ductility values of 12%. The mechanisms of plastic deformation and strengthening of metastable austenitic steel under the above high-temperature thermomechanical treatments are discussed.

High Temperature Oxidation Kinetics of Shot-Peened and Laser-Shock Peened Ti-Beta-21S

2021 ◽  
Author(s):  
V. Optasanu ◽  
M. C. Marco de Lucas ◽  
A. Kanjer ◽  
B. Vincent ◽  
T. Montesin ◽  
...  
Keyword(s):  
High Temperature ◽  
Oxidation Kinetics ◽  
High Temperature Oxidation ◽  
Laser Shock ◽  
Temperature Oxidation ◽  
Kinetics Of

Kinetics of Growth and Structure of Coatings Obtained on Sandelin Steels in the High-Temperature Galvanizing Process

2013 ◽  
Vol 212 ◽  
pp. 127-132 ◽  
Author(s):  
Henryk Kania
Keyword(s):  
High Temperature ◽  
Growth Kinetics ◽  
Structural Components ◽  
Compact Layer ◽  
Two Phase ◽  
Continuous Layer ◽  
Structure Of Coatings ◽  
Zinc Coatings ◽  
Kinetics Of ◽  
Diffuse Coating

In the paper the author presents the results of tests defining the characteristics of behaviour of Sandelin steel in the high-temperature galvanizing process. The growth kinetics of hot-dip zinc coatings on the substrate of 0.05% Si steel in the temperature range of 540-580°C has been established. The structure of the coatings and their phase composition have been developed and the chemical composition of structural components of the coating has be defined. It has been determined that the coating is composed of a compact layer δ1 and an area of a two-phase mixture of δ1 and Zn. The conducted tests confirmed the presence of phase Γ1 , which does not form a continuous layer but it forms individual precipitates which are irregular in shape. The growth kinetics of the coating indicates that an increase in temperature causes a decrease in the coating thickness, which might prove that dissolving processes prevailed over the processes of diffuse coating growth.

High temperature plastic deformation of multilayered YTZP/ZTA composites obtained by tape casting

1998 ◽  
Vol 46 (11) ◽  
pp. 3995-4004 ◽  
Author(s):  
M. Jiménez-Melendo ◽  
C. Clauss ◽  
A. Domi ́nguez-Rodri ́guez ◽  
G. de Portu ◽  
E. Roncari ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
High Temperature ◽  
Tape Casting

Kinetics of the High-Temperature Phosphidation of Nickel

1971 ◽  
Vol 118 (1) ◽  
pp. 101 ◽  
Author(s):  
Yoshinori Sasaki ◽  
Akemi Kato ◽  
Shiro Ueda
Keyword(s):  
High Temperature ◽  
Kinetics Of
Sign in / Sign up

Export Citation Format

Share Document