scholarly journals Analysis of Power Loss of 20 kV Power Distribution

2018 ◽  
Vol 215 ◽  
pp. 01040
Author(s):  
Dasman Dasman
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Power Loss ◽  
Reactive Power ◽  
Voltage Drop ◽  
Action Plan ◽  
Active Power ◽  
Power Losses ◽  
Power Distribution System ◽  
Distribution Line

In the distribution of electrical energy from the plant to the consumer, there is a decrease in quality due to the loss of power (losses). These power losses are caused by a voltage drop across the line and subsequently producing a power loss on the line. This power loss can be classified into two types based on its line parameters, i.e., active power loss and reactive power loss. The line’s active power loss generates losses of power/losses so that the active power reaches the load on the receiving end is always less than the productive power of the sender side. Power losses in the electrical system must exist and cannot be reduced to 0% (zero percent). According to SPLN No. 72 of 1987, the permitted distribution network’s power loss should not be higher than 10%. This paper investigates the magnitude of the voltage loss and the line active power losses on the 20 kV distribution line. The calculation conducted through case study and simulation of Etap 12.6 program on an electrical power distribution system that is 20 kV distribution line in PT. PLN (Persero) Rayon Muara Labuh. In the distribution line 20 kV, there is IPP (Independent Power Plant) PLTMH PT SKE used to improve the stress conditions in Rayon Muara Labuh. Therefore the loss of power will be calculated in 3 terms, i.e., before and after IPP PT. SKE with 20 kV distribution lines as well as on feeder load maintenance (as a repair action plan). The simulation results show the highest voltage drop and the highest power losses continue generated during IPP. PT SKE has not done synchronized with the distribution line of 20 kV with a significant voltage drop of 1,533 kV percentage of 7.93% and power loss of 777.528 kWh percentage of 7.69%.

scholarly journals REKONFIGURASI JARINGAN PADA SALURAN UDARA TEGANGAN MENENGAH 20 KV PENYULANG NAIONI PT. PLN (PERSERO) ULP KUPANG MENGGUNAKAN PERANGKAT LUNAK ELECTRICAL TRANSIENT ANALYSIS PROGRAM (ETAP) 12.6

2019 ◽  
pp. 41-52
Author(s):  
Nikolaus M. Tana ◽  
Frans Likadja ◽  
Wellem F. Galla
Keyword(s):  
Power Loss ◽  
Reactive Power ◽  
Voltage Drop ◽  
Capacitor Bank ◽  
Active Power ◽  
Total Power ◽  
Power Losses ◽  
Overhead Lines ◽  
Medium Voltage ◽  
Active Power Losses

The 20 kV medium Voltage overhead lines of Naioni feeder on PT. PLN (Persero) ULP Kupang system has a feed length of ± 79.825 kms and is the longest of all feeders installed in the ULP Kupang. To minimize the voltage drop and power losses on the Naioni Feeder 20 kV medium Voltage overhead lines (SUTM), network reconfiguration needs to be done including changing the diameter of the conductor, installing a transformer insert and installing a capacitor bank using the help of ETAP software. From the results of the study, before reconfiguration, the voltage drop at the end of the Bus_Trafo KB 082 channel was 0.967 kV and the voltage drop percentage was 4.68% while the total power losses at Naioni Feeder were 20 kV, which were active power losses of 48.062 kW and loss reactive power loss of 25,689 kVAR. Furthermore, after reconfiguring the carrying diameter on the channel that still uses a small diameter of 35 mm2, it will be converted to 70 mm2 on cable 17 that connects the KB 119 Transformer Bus channel to the KB 074 Transformer Bus which is a fairly long distance from all other channels. So that after carrying out the reconfiguration of the conductor diameter, the voltage drop at the end of the Bus Trafo KB 082 channel is 0.844 kV and the voltage drop percentage is 4.24%, while the total power losses in the Naioni Feeder are 20 kV which are active power losses of 41.142 kW and conductor reactive power loss of 25.53 kVAR. Furthermore, after installation of the transformer insert and changing the conductor diameter on cable 17 of 35 mm2 will be changed to 70 mm2 connecting the Transformer Bus Channel KB 119 to the KB 074 Transformer Bus, then the voltage drop at the end of the Bus Trafo KB 082 channel is 0.826 kV and the voltage drop percentage amounting to 4.15% while the total power losses at Naioni Feeder are 20 kV, namely active power losses of39.292 kW and reactive power losses of 24.467 kVAR. And then, if the capacitor bank is installed on the Bus Transformer KB 119 channel bus point to the Bus Trafo KB 074 channel, then the voltage drop at the Bus Trafo KB 082 channel end is 0.891 kV and the voltage drop percentage is 4.47%, while the total power losses are The 20 kV Naioni Feeder is an active power loss of 43.714 kW and a reactive power loss of 22.888 kVAR.

scholarly journals Simulasi ETAP 12.6 untuk Studi Instalasi Listrik pada Kereta Api Kahuripan

MIND Journal ◽  
2021 ◽  
Vol 6 (1) ◽  
pp. 118-131
Author(s):  
FARIZ GHILYATS IRFAN ◽  
NASRUN HARIYANTO
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Power Loss ◽  
Voltage Drop ◽  
Circuit Breaker ◽  
Load Flow ◽  
Cross Sectional ◽  
Power Distribution System ◽  
Section Size ◽  
Cross Sectional Size

AbstrakDalam sebuah satu rangkaian kereta biasanya terdiri dari penggerak utama lokomotif, kereta penumpang, kereta makan, dan kereta pembangkit. Dengan banyaknya fasilitas dan alat-alat kelistrikan dalam gerbong-gerbong tersebut dapat memberikan dampak penurunan terhadap kualitas daya listrik yang mengalir pada sistem distribusi aliran daya. Penelitian ini bertujuan untuk mengetahui kapasitas nilai circuit breaker, ukuran penampang kabel,  tegangan jatuh, dan rugi-rugi daya, serta perbandingangannya dengan hasil simulasi pada software ETAP 12.6. Kapasitas circuit breaker dan ukuran penampang kabel yang diperhitungkan mendapatkan rating circuit breaker dengan arus berkisar dari 800 hingga 80 Ampere dan ukuran kabel yang digunakan sebesar 120 mm2. Hasil nilai drop voltage yang didapat dimulai dari 1,02 Volt hingga 5,08 Volt. Untuk nilai rugi-rugi daya yang didapat dimulai dari dari 0,01 kW hingga 0,11 kW.Kata kunci: Aliran Beban, ETAP, Circuit Breaker, Drop Voltage, Rugi-rugi Daya.AbstractA train usually consists of several carrieges: a prime mover locomotive, passenger carriage, dining carriage, and generator carriage. With that many facilities and installed electrical equipments the quality of the electric power flowing in the trains’s power distribution system may be decresed. This study aims to determine the capacity of the circuit breaker, the cable’s cross section size, the voltage drop, and power losses, as well as the comparison with the simulation results by using ETAP software. The circuit breaker capacity and cable’s cross-sectional size are calculated. From the calculations, we obtain the rating value for the circuit breaker, which is ranging from 800 to 80 Ampere. As for the cable’s corss sectional we obtain 120 mm2. With these values, the resulting voltage drop is from 1.02 Volts to 5.08 Volts. As for the resulting power loss, its value is ranging from 0.01 kW to 0.11 kW.Keywords: Load Flow, ETAP, Circuit Breaker, Voltage Drop, Power Loss.  

scholarly journals Line-End Voltage and Voltage Profile along Power Distribution Line with Large-Power Photovoltaic Generation System

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Toshiro Matsumura ◽  
Masumi Tsukamoto ◽  
Akihiro Tsusaka ◽  
Kazuto Yukita ◽  
Yasuyuki Goto ◽  
...  
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Reverse Current ◽  
Generation System ◽  
Pv System ◽  
Photovoltaic Generation ◽  
Voltage Rise ◽  
Power Distribution System ◽  
Line Current ◽  
Distribution Line

In recent years, the introduction of the photovoltaic generation system (PV system) has been increasing by promoting the use of renewable energy. It has been feared that the reverse current from the PV system may cause an unacceptable level of voltage rise at the interconnection node in the power distribution system. This paper discusses the effects of the reverse current on the voltage rise and fall characteristics of the interconnection node and the voltage profiles along the power distribution line. When the line current on the circuit is small, the voltage on the line monotonically increases from the sending end to the receiving end. When a relatively large current flows, it causes a voltage reduction near the distribution substation. Furthermore, on the basis of the voltage aspects in the power distribution system with a large PV system, the allowable limits of the line current and the output power from PV system are investigated.

A Novel Control Strategy for Three-Phase Four-Wire STATCOM

2012 ◽  
Vol 516-517 ◽  
pp. 1722-1727 ◽  
Author(s):  
Wei Jun Yun ◽  
Gang Yao ◽  
Li Dan Zhou ◽  
Chen Chen ◽  
Jun Min Pan
Keyword(s):  
Control Strategy ◽  
Power Distribution ◽  
Distribution System ◽  
Reactive Power ◽  
Control Method ◽  
Loop Control ◽  
Power Distribution System ◽  
Imbalance Problem ◽  
Three Phase ◽  
Close Loop Control

Nowadays Static Synchronous Compensator (STATCOM) has gradually become one of the representative techniques in the field of dynamic reactive power compensation in the power distribution system. This paper analyzed the topology and the voltage imbalance problem of the up and down capacitors on DC side of the three-phase four-wire STATCOM. In allusion to the imbalance problem of neutral point, a novel control strategy based on the control of zero-sequence current was proposed. By the triple close-loop control strategy, the STATCOM can achieve great control accuracy and dynamic performance. Simulation result proves that the proposed control method is effective.

scholarly journals ANALISIS DROP TEGANGAN PADA JARINGAN TEGANGAN MENENGAH DENGAN MENGGUNAKAN SIMULASI PROGRAM ETAP

2019 ◽  
Vol 10 (1) ◽  
pp. 26-37
Author(s):  
Redaksi Tim Jurnal
Keyword(s):  
Electric Power ◽  
Power Distribution ◽  
Distribution System ◽  
Low Voltage ◽  
Voltage Drop ◽  
Power Distribution System ◽  
Medium Voltage ◽  
Cable Channel ◽  
Electric Power Distribution ◽  
Manual Calculation

Distribution system is very important in the distribution of electric power to the load. Therefore, a good and efficient distribution system is needed. The underlying cause of poor electric power distribution system is the amount of voltage drop values in the existing system. In the electric power distribution, 20 kV medium-voltage and 380/220V low voltage networks are used. The distribution system of Gandum Feeder in Angke Substation uses medium-voltage network with Underground Cable channel. They are used because of the towering buildings and the dense population in the area. It is known that the longest the channel and the load current are, the greater the voltage drop. From the result of the voltage drop calculation of Feeder Gandum in Angke Substation, which uses manual calculation and ETAP 12.6.0 program, it showed a slight difference in the result. The result of the voltage drop obtained from manual calculation showed that the percentage value of voltage is 1,94%, while the result obtained from ETAP 12.6.0 program showed that the percentage value is 2,01% These results are still in the PLN standard, because it has not exceeded the specified standard that is -10% of its nominal voltage.

scholarly journals DSTATCOM Performance for Voltage Sag/swell Mitigation

2020 ◽  
Vol 9 (2) ◽  
pp. 71-74
Keyword(s):  
Power Quality ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Reactive Power ◽  
Power Transmission ◽  
Control Technique ◽  
Power Distribution System ◽  
Industrial Sectors ◽  
Voltage Compensation

The Indian economy has been growing at a fast pace since the beginning of this millennium. Due to constraints in the availability of fuel and environmental concerns, the power generation sector has not kept pace with other industrial sectors. One way of increasing the power availability is by reducing the high losses in the existing power transmission and distribution systems. The current increases in the motor windings when the voltages in the three phases are unbalanced. Compensation for reactive power and unbalance in the power distribution system are key factors in improving the power quality to the end user. A Distributed Static Compensator [DSTATCOM] is a custom power device, which is connected in shunt with the load in the distribution system to compensate the reactive power due unbalanced loads. The performance of the DSTATCOM is based on the control technique used for finding the voltage referred and current components to be considered. Voltage compensation is defined as the error in voltage in the grid and that the value of voltage that has to be induced in the grid. This is analyzed by using DSTATCOM for voltage compensation with series converter controller block. This paper gives the simulation of voltage compensation to rectify the issue of voltage swell/sag in order to improve the power quality in the distribution system.

scholarly journals Network Reconfiguration of Primary Distribution System Using GWO Algorithm

2017 ◽  
Vol 7 (6) ◽  
pp. 3226 ◽  
Author(s):  
A. V. Sudhakara Reddy ◽  
M. Damodar Reddy ◽  
M. Satish Kumar Reddy
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Power Loss ◽  
Distribution Systems ◽  
Network Reconfiguration ◽  
Grey Wolf ◽  
Grey Wolf Optimization ◽  
Real Power ◽  
Power Distribution System ◽  
Power Loss Reduction

This manuscript presents a feeder reconfiguration in primary distribution networks with an objective of minimizing the real power loss or maximization of power loss reduction. An optimal switching for the network reconfiguration problem is introduced in this article based on step by step switching and simultaneous switching. This paper proposes a Grey Wolf Optimization (GWO) algorithm to solve the feeder reconfiguration problem through fitness function corresponding to optimum combination of switches in power distribution systems. The objective function is formulated to solve the reconfiguration problem which includes minimization of real power loss. A nature inspired Grey Wolf Optimization Algorithm is utilized to restructure the power distribution system and identify the optimal switches corresponding minimum power loss in the distribution network. The GWO technique has tested on standard IEEE 33-bus and 69-bus systems and the results are presented.

scholarly journals Multi-objective Evolutionary Algorithms for Power Distribution System Optimal Reconfiguration

2019 ◽  
Vol 22 (3) ◽  
Author(s):  
Ivo Benitez Cattani
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Multi Objective Optimization ◽  
Power Losses ◽  
Nsga Ii ◽  
Power Distribution System ◽  
Multi Objective ◽  
Three Phase ◽  
Unbalanced Voltage

In this paper two reconfiguration methodologies for three-phase electric power distribution systems based on multi-objective optimization algorithms are developed in order to simultaneously optimize two objective functions, (1) power losses and (2) three-phase unbalanced voltage minimization. The proposed optimization involves only radial topology configurations which is the most common configuration in electric distribution systems. The formulation of the problem considers the radiality as a constraint, increasing the computational complexity. The Prim and Kruskal algorithms are tested to fix infeasible configurations. In distribution systems, the three-phase unbalanced voltage and power losses limit the power supply to the loads and may even cause overheating in distribution lines, transformers and other equipment. An alternative to solve this problem is through a reconfiguration process, by opening and/or closing switches altering the distribution system configuration under operation. Hence, in this work the three-phase unbalanced voltage and power losses in radial distribution systems are addressed as a multi-objective optimization problem, firstly, using a method based on weighted sum; and, secondly, implementing NSGA-II algorithm. An example of distribution system is presented to prove the effectiveness of the proposed method.

Sign in / Sign up

Export Citation Format

Share Document