scholarly journals Application of the High Early Strength Type Expansive Agent to the Blast Furnace Slag Combination Concrete with GGBFS under Steam Curing

2019 ◽  
Vol 278 ◽  
pp. 01005
Author(s):  
Erica Enzaki ◽  
Takashi Sakuma ◽  
Eizou Takeshita ◽  
Shigeyuki Date
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Early Stage ◽  
Precast Concrete ◽  
Curing Temperature ◽  
Strength Development ◽  
Steam Curing ◽  
Expansive Agent ◽  
Early Strength ◽  
Furnace Slag

In recent years, the use of blast furnace slag material is being focused as environmental loading reduction and sustainable construction. However, in general, autogeneours shrinkage of the concrete using much amount of GGBFS is large in compared to normal concrete, therefore risk of cracking should be cared. On the other hand, strength development speed of concrete at early stage will be decreasing as the dosage of GGBFS increases, even under steam curing condition. It can be considered these points will be significant disadvantage in both productivity and quality of precast concrete. So in this study, early strength type expansive agent and setting accelerator were used in combination. As a result, it was confirmed that compressive strength at early stage is obviously increased. And steam curing temperature can be reduced about 10 degrees, and also, 600×10-6 of restraint expansion was obtained.

Effect of Type of Cement and Expansive Agent on the Hardening of Steam-Cured Concrete

2017 ◽  
Vol 744 ◽  
pp. 105-113 ◽  
Author(s):  
Takayoshi Maruyama ◽  
Hideaki Karasawa ◽  
Shigeyuki Date
Keyword(s):  
Early Stage ◽  
Precast Concrete ◽  
Curing Temperature ◽  
Steam Curing ◽  
Slag Powder ◽  
Expansive Agent ◽  
Cast Concrete ◽  
Increase Productivity ◽  
Early Strength ◽  
Furnace Slag

Pre-cast concrete products are sometimes manufactured in two cycles daily. It is ensured that they have the required strength at an early stage of demolding by increasing the steam curing temperature to reduce cost or increase productivity. However, the reduction in durability because of cracking due to thermal stress is a topic of concern. On the other hand, it has been known that fine blast-furnace-slag powder and expansive agents show high temperature dependence. Although they are used even in precast concrete products, the effect of steam curing on these materials is not known. Thus, in this study, the expression of compressive strength and expansion that are critical in improving the quality and productivity of precast concrete products was investigated, using high early-strength cement and two types of expansive agents, namely, ettringite-based and lime-based agents. Consequently, the strength expression was accelerated by the addition of expansive agent to ordinary cement and high early-strength cement. The extent of restrained expansion is greater for the lime-based expansive agent than for the ettringite-based expansive agent, and when an expansive agent is added to high early-strength cement, the extent of restrained expansion falls to a level lower than that in the case of ordinary cement.

scholarly journals Early Strength Development of Soft Clay Stabilized by One-Part Ground Granulated Blast Furnace Slag and Fly Ash-Based Geopolymer

2021 ◽  
Vol 8 ◽  
Author(s):  
Xiyao Zheng ◽  
Jun Wu
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Soft Clay ◽  
Strength Development ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Early Strength ◽  
Furnace Slag ◽  
Water Binder Ratio

One-part or “just add water” geopolymer is a cementitious material, which is friendly to environment and users in applications. However, the mechanical behavior of the soft soil stabilized by one-part geopolymer is not well acknowledged. In this study, soft clay was stabilized with ground granulated blast furnace slag (GGBFS) and fly ash (FA)-based geopolymer, which is a mixture of solid aluminosilicate precursor (Al-Si raw materials: GGBFS and FA), solid alkali activator, and water. The objective was to adopt one-part geopolymer as an alternative soil binder to completely replace ordinary Portland cement (OPC) for stabilizing the soft clay and evaluate the effect of the factors (i.e., GBFS/FA ratio in Al-Si precursor, activator/Al-Si precursor ratio, and water/binder ratio) that influenced the early strength. Results showed that the increase of the FA content in the Al-Si precursor increased the unconfined compressive strength (UCS) values significantly through the geopolymerization process. The highest UCS values were achieved with 90% GGBFS to 10% FA in the precursor when the activator/precursor and water/binder ratio is 0.15 and 0.7, respectively. The UCS values of geopolymer-stabilized clay could reach 1.5 MPa at 14 days at ambient temperature, which is much higher than that of OPC-stabilized clay. The microstructure and mineralogy analyses indicated that the prolific hydration products, such as calcium silicate hydrate (C-S-H), calcium aluminum hydrate (C-A-H), and calcium aluminum silicate hydrate (C-A-S-H), contributed greatly to strengthen the soft clay by forming the soil skeleton and infilling among clay particles, while sodium aluminosilicate (N-A-S-H) gel is only served to fill the part of porosities in the soil and cannot effectively enhance the UCS of the one-part geopolymer-stabilized soft clay. This paper results suggested that one-part GGBFS-FA–based geopolymers have the potential to replace OPC in the manufacture of stabilized soft clay.

Improvement of Durability of Precast Concrete Member by Granulated Blast Furnace Slag Sand

2017 ◽  
Vol 12 (3) ◽  
pp. 456-469 ◽  
Author(s):  
Toshiki Ayano ◽  
◽  
Takashi Fujii ◽  
Kyoji Niitani ◽  
Katsunori Takahashi ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Precast Concrete ◽  
Heavy Traffic ◽  
Concrete Slabs ◽  
Fine Aggregate ◽  
Freezing And Thawing ◽  
Steam Curing ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Concrete deck slabs of bridges are often deteriorated by heavy traffic and freezing and thawing actions. Spraying salt during the winter further promotes the deterioration of concrete. Some reports estimate that the length of highway roads requiring the renewal of deteriorated concrete slabs exceeds 230 km. In order to extend the lifespan of damaged bridge girders, the load for these girders must not be increased. This means that prestressed concrete (hereafter, PC) members are desirable to sustain bridge life, because they can be thinner than reinforced concrete (hereafter, RC) members. In addition, to shorten the period of traffic regulation during renewal construction, precast members should be applied. One problem in manufacturing durable precast concrete is steam curing. When the temperature, period, or both of the steam curing process are inadequate, the effect of air-entraining (hereafter, AE) agents is lost because the warmed air trapped by the AE agent expands and escapes from the concrete. Another problem is concrete fatigue. It is well known that the fatigue lives of concrete slabs in wet conditions are much shorter than those in dry conditions. Concrete slabs are waterproofed immediately after construction, but the waterproofing can be fractured soon after opening bridges, and water can reach the concrete surface. The lifespan of concrete slabs in contact with water often depends on the fatigue of the concrete. Granulated blast furnace slag sand (hereafter, BFS) can enhance the resistance to freezing and thawing actions without using AE agents. Therefore, the resistance to freezing and thawing of concrete mixed with BFS is not damaged by steam curing. The fatigue of concrete in water is also improved by the addition of BFS. Furthermore, BFS can reduce the drying shrinkage of concrete. It is advantageous to restrict the loss of prestress in PC. This study shows that precast PC members with high durability can be manufactured when granulated blast furnace slag is used as a fine aggregate in the concrete. BFS reacts with cement hydrates. It is well known that the carbonation of concrete with ground granulated blast furnace slag (hereafter, GGBF) is much greater than that with ordinary binder. However, BFS does not accelerate the carbonation of concrete. When using granulated blast furnace slag as a fine aggregate, no disadvantage in the concrete properties is detected.

scholarly journals Evaluation of Strength Development in Concrete with Ground Granulated Blast Furnace Slag Using Apparent Activation Energy

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 442 ◽  
Author(s):  
Hyun-Min Yang ◽  
Seung-Jun Kwon ◽  
Nosang Vincent Myung ◽  
Jitendra Kumar Singh ◽  
Han-Seung Lee ◽  
...  
Keyword(s):  
Activation Energy ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Apparent Activation Energy ◽  
Blast Furnace Slag ◽  
Curing Temperature ◽  
Strength Development ◽  
Replacement Ratio ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Ground granulated blast furnace slag (GGBFS) conventionally has been incorporated with ordinary Portland cement (OPC) owing to reduce the environmental load and enhance the engineering performance. Concrete with GGBFS shows different strength development of normal concrete, but sensitive, to exterior condition. Thus, a precise strength evaluation technique based on a quantitative model like full maturity model is required. Many studies have been performed on strength development of the concrete using equivalent age which is based on the apparent activation energy. In this process, it considers the effect of time and temperature simultaneously. However, the previous models on the apparent activation energy of concrete with mineral admixtures have limitation, and they have not considered the effect of temperature on strength development. In this paper, the apparent activation energy with GGBFS replacement ratio was calculated through several experiments and used to predict the compressive strength of GGBFS concrete. Concrete and mortar specimens with 0.6 water/binder ratio, and 0 to 60% GGBFS replacement were prepared. The apparent activation energy (Ea) was experimentally derived considering three different curing temperatures. Thermodynamic reactivity of GGBFS mixed concrete at different curing temperature was applied to evaluate the compressive strength model, and the experimental results were in good agreement with the model. The results show that when GGBFS replacement ratio was increased, there was a delay in compressive strength.

scholarly journals Effect of High-Temperature Curing Methods on the Compressive Strength Development of Concrete Containing High Volumes of Ground Granulated Blast-Furnace Slag

2017 ◽  
Vol 2017 ◽  
pp. 1-6
Author(s):  
Wonsuk Jung ◽  
Se-Jin Choi
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
High Temperature ◽  
Blast Furnace Slag ◽  
Precast Concrete ◽  
Strength Development ◽  
Peak Period ◽  
Granulated Blast Furnace Slag ◽  
Curing Methods ◽  
Furnace Slag

This paper investigates the effect of the high-temperature curing methods on the compressive strength of concrete containing high volumes of ground granulated blast-furnace slag (GGBS). GGBS was used to replace Portland cement at a replacement ratio of 60% by binder mass. The high-temperature curing parameters used in this study were the delay period, temperature rise, peak temperature (PT), peak period, and temperature down. Test results demonstrate that the compressive strength of the samples with PTs of 65°C and 75°C was about 88% higher than that of the samples with a PT of 55°C after 1 day. According to this investigation, there might be optimum high-temperature curing conditions for preparing a concrete containing high volumes of GGBS, and incorporating GGBS into precast concrete mixes can be a very effective tool in increasing the applicability of this by-product.

A Study on Environmental Load Assessment of Early Strength Activator Blast Furnace Slag

2014 ◽  
Vol 905 ◽  
pp. 383-387
Author(s):  
Young Jin Bok ◽  
Sung Ho Tae ◽  
Taeh Young Kim ◽  
Jeong Hun Park
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Building Materials ◽  
Strength Development ◽  
Environmental Load ◽  
Mortar Specimen ◽  
Early Strength ◽  
Environment Performance ◽  
Furnace Slag ◽  
By Products

Development of environment-friendly building materials has recently been increasing with the use of industrial waste and by-products, but concrete containing blast furnace slag (BFS) is excellent in terms of environmental load and shows relatively insufficient early strength. Development of by-products to supplement this insufficiency is deemed necessary. Therefore in this study, an early strength activator blast furnace slag (A-BFS) was developed and environment performance of the developed A-BFS was assessed to assess environmental load (CO2). As a result, early strength was developed in mortar specimen mixed with A-BFS. When environmental load (CO2) was assessed on the mortar specimen, life cycle CO2 emission from production of 1kg of A-BFS was found to be 0.057kg-CO2/kg.

Sign in / Sign up

Export Citation Format

Share Document