Developing Master Curves and Predicting Dynamic Modulus of Polymer-Modified Asphalt Mixtures

2011 ◽  
Vol 23 (2) ◽  
pp. 131-137 ◽  
Author(s):  
Haoran Zhu ◽  
Lu Sun ◽  
Jun Yang ◽  
Zhiwei Chen ◽  
Wenjun Gu
Keyword(s):  
Dynamic Modulus ◽  
Asphalt Mixtures ◽  
Master Curves ◽  
Modified Asphalt ◽  
Polymer Modified Asphalt

scholarly journals Predict the Phase Angle Master Curve and Study the Viscoelastic Properties of Warm Mix Crumb Rubber-Modified Asphalt Mixture

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5051
Author(s):  
Fei Zhang ◽  
Lan Wang ◽  
Chao Li ◽  
Yongming Xing
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Master Curve ◽  
Loss Modulus ◽  
Asphalt Mixture ◽  
Crumb Rubber ◽  
Asphalt Mixtures ◽  
Master Curves ◽  
Modified Asphalt ◽  
Sigmoidal Model

To identify the most accurate approach for constructing of the dynamic modulus master curves for warm mix crumb rubber modified asphalt mixtures and assess the feasibility of predicting the phase angle master curves from the dynamic modulus ones. The SM (Sigmoidal model) and GSM (generalized sigmoidal model) were utilized to construct the dynamic modulus master curve, respectively. Subsequently, the master curve of phase angle could be predicted from the master curve of dynamic modulus in term of the K-K (Kramers–Kronig) relations. The results show that both SM and GSM can predict the dynamic modulus very well, except that the GSM shows a slightly higher correlation coefficient than SM. Therefore, it is recommended to construct the dynamic modulus master curve using GSM and obtain the corresponding phase angle master curve in term of the K-K relations. The Black space diagram and Wicket diagram were utilized to verify the predictions were consistent with the LVE (linear viscoelastic) theory. Then the master curve of storage modulus and loss modulus were also obtained. Finally, the creep compliance and relaxation modulus can be used to represent the creep and relaxation properties of warm-mix crumb rubber-modified asphalt mixtures.

Dynamic Modulus Characteristic of Large Stone Permeable Asphalt Mixtures

2013 ◽  
Vol 423-426 ◽  
pp. 1110-1113
Author(s):  
Jin Cheng Wei ◽  
Jin Li
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Asphalt Mixtures ◽  
Sigmoidal Function ◽  
Master Curves ◽  
Low Frequencies ◽  
High Frequencies ◽  
Modified Asphalt ◽  
Large Stone ◽  
Dynamic Modulus Test

To study the dynamic modulus characteristic of LSPM mixes, dynamic modulus test was conducted for Large Stone Permeable Asphalt Mixtures (LSPM ) with neat asphalt and with modified asphalt and the range of dynamic modulus values for LSPM was determined and the dynamic modulus master curves were developed. The magnitude of the dynamic modulus decreased with an increase in temperature and increased with an increase in the frequency. The phase angle decreased as the frequency increased at low temperature. With temperature increase, there was a transition interval, where the phase angle increased up to frequencies of 0.5 Hz, and then it started to decrease as frequency increased. After the transition interval, the phase angle increased with an increase in frequency. Master curves developed by sigmoidal function showed that LSPM with modified asphalt exhibited higher dynamic modulus values at middle and high frequencies and lower dynamic modulus values at low frequencies.

scholarly journals Mechanical Characteristics of Graphene Nanoplatelets-Modified Asphalt Mixes: A Comparison with Polymer- and Not-Modified Asphalt Mixes

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2434
Author(s):  
Laura Moretti ◽  
Nico Fabrizi ◽  
Nicola Fiore ◽  
Antonio D’Andrea
Keyword(s):  
Fatigue Resistance ◽  
Graphene Nanoplatelets ◽  
Asphalt Mixtures ◽  
Asphalt Binders ◽  
Asphalt Mixes ◽  
Modified Asphalt ◽  
Bituminous Mixtures ◽  
Water Sensitivity ◽  
Polymer Modified Asphalt ◽  
Mechanical Performances

In recent years, nanotechnology has sparked an interest in nanomodification of bituminous materials to increase the viscosity of asphalt binders and improves the rutting and fatigue resistance of asphalt mixtures. This paper presents the experimental results of laboratory tests on bituminous mixtures laid on a 1052 m-long test section built in Rome, Italy. Four asphalt mixtures for wearing and binder layer were considered: two polymer modified asphalt concretes (the former modified with the additive Superplast and the latter modified with styrene–butadiene–styrene), a “hard” graphene nanoplatelets (GNPs) modified asphalt concrete and a not-modified mixture. The indirect tensile strength, water sensitivity, stiffness modulus, and fatigue resistance of the mixtures were tested and compared. A statistical analysis based on the results has shown that the mixtures with GNPs have higher mechanical performances than the others: GNP could significantly improve the tested mechanical performances; further studies will be carried out to investigate its effect on rutting and skid resistance.

Dynamic Modulus of Western Australia Asphalt Wearing Course

2014 ◽  
Vol 71 (3) ◽  
Author(s):  
Gunawan Wibisono ◽  
Hamid Nikraz
Keyword(s):  
Western Australia ◽  
Dynamic Modulus ◽  
Asphalt Mixtures ◽  
Predictive Equation ◽  
Master Curves ◽  
Time Rate ◽  
Low Frequencies ◽  
Design Guide ◽  
Preliminary Study ◽  
Air Void

In the new AASHTO Mechanistic-Empirical Pavement Design Guide (MEPDG), the dynamic modulus |E*| test has been selected to assess the performance of asphalt concretes. The type of test, which relates asphalt mixtures modulus to temperature and time rate of loading, is never used in Western Australia. This paper presents a study on the dynamic modulus of typical Western Australia asphalt mixtures. Five mixtures with 10mm nominal sizes and two types of bitumen classes, i.e. C170 (Pen 60/80) and C320 (Pen 40/60) comply with Main Road Western Australia (MRWA) Specification were used in the research. Mixing and compacting process were carried out according to Austroads methods. The specimens were compacted using a gyratory compactor to achieve 5±0.5% target air void. Testing was performed at four temperatures (4, 20, 40 and 55OC) and six frequencies (25, 10, 5, 1, 0.5, 0.1 and 0.05 Hz). Dynamic modulus and phase angle master curves were generated from the results. The master curves were compared to the curves from Witczak’s predictive equation. From this preliminary study, it was found that the measured values correlated well with the predictive equation except at high temperatures or low frequencies. 

Characteristic Analysis of Dynamic Modulus for High Modulus Asphalt Concrete

2014 ◽  
Vol 505-506 ◽  
pp. 15-18 ◽  
Author(s):  
Xiao Long Zou ◽  
Ai Min Sha ◽  
Wei Jiang ◽  
Xin Yan Huang
Keyword(s):  
Dynamic Modulus ◽  
Testing Machine ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
High Modulus ◽  
Characteristic Analysis ◽  
Modified Asphalt ◽  
Universal Testing ◽  
Different Temperatures ◽  
Dynamic Modulus Test

In order to analyze the characteristics of high modulus asphalt mixture dynamic modulus, Universal Testing Machine (UTM-25) was used for dynamic modulus test of three kinds of mixtures, which were PR Module modified asphalt mixture and PR PLAST.S modified asphalt mixture and virgin asphalt mixture, to investigate dynamic modulus and phase angle at different temperatures and frequencies. The results indicate that: the dynamic modulus order of the three asphalt mixtures is PR MODULE > PR PLAST.S > Virgin. PR MODULE asphalt mixture dynamic modulus is much larger than the other two.

Sign in / Sign up

Export Citation Format

Share Document