scholarly journals Predict the Phase Angle Master Curve and Study the Viscoelastic Properties of Warm Mix Crumb Rubber-Modified Asphalt Mixture

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5051
Author(s):  
Fei Zhang ◽  
Lan Wang ◽  
Chao Li ◽  
Yongming Xing
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Master Curve ◽  
Loss Modulus ◽  
Asphalt Mixture ◽  
Crumb Rubber ◽  
Asphalt Mixtures ◽  
Master Curves ◽  
Modified Asphalt ◽  
Sigmoidal Model

To identify the most accurate approach for constructing of the dynamic modulus master curves for warm mix crumb rubber modified asphalt mixtures and assess the feasibility of predicting the phase angle master curves from the dynamic modulus ones. The SM (Sigmoidal model) and GSM (generalized sigmoidal model) were utilized to construct the dynamic modulus master curve, respectively. Subsequently, the master curve of phase angle could be predicted from the master curve of dynamic modulus in term of the K-K (Kramers–Kronig) relations. The results show that both SM and GSM can predict the dynamic modulus very well, except that the GSM shows a slightly higher correlation coefficient than SM. Therefore, it is recommended to construct the dynamic modulus master curve using GSM and obtain the corresponding phase angle master curve in term of the K-K relations. The Black space diagram and Wicket diagram were utilized to verify the predictions were consistent with the LVE (linear viscoelastic) theory. Then the master curve of storage modulus and loss modulus were also obtained. Finally, the creep compliance and relaxation modulus can be used to represent the creep and relaxation properties of warm-mix crumb rubber-modified asphalt mixtures.

scholarly journals Mesostructural Modeling of Dynamic Modulus and Phase Angle Master Curves of Rubber Modified Asphalt Mixture

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1667 ◽  
Author(s):  
Linhao Gu ◽  
Luchuan Chen ◽  
Weiguang Zhang ◽  
Haixia Ma ◽  
Tao Ma
Keyword(s):  
Finite Element ◽  
Phase Angle ◽  
Dynamic Modulus ◽  
Master Curve ◽  
Asphalt Mixture ◽  
Maxwell Model ◽  
Master Curves ◽  
Modified Asphalt ◽  
2S2p1d Model ◽  
Asphalt Mortar

The main objective of this paper was to develop a mesostructure-based finite element model of rubber modified asphalt mixture to predict both the dynamic modulus master curve and phase angle master curve under a large frequency range. The asphalt mixture is considered as a three-phase material consisting of aggregate, asphalt mortar, and air void. The mesostructure of the asphalt mixture was digitized by a computed tomography (CT) scan and implemented into finite element software. The 2S2P1D model was used to obtain the viscoelastic information of an asphalt mortar under a large range of frequencies and temperatures. The continuous spectrum of the 2S2P1D model was converted to a discrete spectrum and characterized by the generalized Maxwell model for numerical simulation. The Prony series parameters of the generalized Maxwell model and the elastic modulus of the aggregates were inputted into the finite element analysis as material properties. The dynamic modulus tests of a rubber modified asphalt mortar and asphalt mixture were conducted under different temperatures and loading frequencies. The dynamic modulus master curve and phase angle master curve of both asphalt mortar and asphalt mixture were constructed. The frequency of the finite element simulations of the dynamic modulus tests ranged from 10−6 to 104. The dynamic modulus and phase angle of the asphalt mixture was calculated and the master curves were compared with the master curves obtained from the experimental data. Furthermore, the effect of the elastic modulus of aggregates on the master curves was analyzed. Acceptable agreement between dynamic modulus master curves obtained from experimental data and simulation results was achieved. However, large errors between phase angle master curves appeared at low frequencies. A method was proposed to improve the prediction of the phase angle master curve by adjusting the equilibrium modulus of the asphalt mortar.

Study on Dynamic Modulus of Waste Plastic Modified Asphalt Mixture Using Waste Plastic Bag Chips

2011 ◽  
Vol 261-263 ◽  
pp. 824-828 ◽  
Author(s):  
Qian Zhang ◽  
Shu Wei Goh ◽  
Zhan Ping You
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Asphalt Mixture ◽  
Control Sample ◽  
Asphalt Mixtures ◽  
Test Results ◽  
Waste Plastic ◽  
Modified Asphalt ◽  
Plastic Bag ◽  
Dynamic Modulus Test

The objective of this study is to investigate the possibility of using waste plastic as an additive to modify asphalt mixtures thereby reducing the waste plastic stream in our environment. High density polyethylene plastic bags obtained from the retail store were shredded into chips and added into asphalt mixtures at the rate of 0% (control sample), 2, 5 and 8% based on binder weight. Three different temperatures of 4, 21.3 and 39.2°C and frequencies ranging from 0.1 to 25 Hz were used in the dynamic modulus test. It was found that most of the asphalt mixtures modified with waste plastic have higher dynamic modulus when compared with the control samples. However, no significant trend on phase angle was found among all the samples tested based on the test results. In this study, it was found that the modified asphalt mixture with 2% waste plastic had the highest dynamic modulus and phase angle. Based on the test results, it was found that plastic modified asphalt mixture will have a better performance under intermediate and high temperature conditions.

scholarly journals The Effects of Asphalt Migration on the Dynamic Modulus of Asphalt Mixture

2019 ◽  
Vol 9 (13) ◽  
pp. 2747 ◽  
Author(s):  
Hui Wang ◽  
Shihao Zhan ◽  
Guojun Liu
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Testing Temperature ◽  
Asphalt Mixtures ◽  
Loading Frequency ◽  
Stiffness Parameter ◽  
Master Curves ◽  
Asphalt Content

Asphalt migration is one of the significant detrimental effects on asphalt pavement performance. In order to simulate the state after the occurrence of asphalt migration amid asphalt pavement layers and further investigate the effects of asphalt migration on the dynamic modulus of asphalt mixture, samples with different asphalt contents layers were firstly separated into the upper and lower half portions and then compacted together. By conducting the dynamic modulus test with the Superpave Simple Performance Tester (SPT), the variation laws of the dynamic modulus (|E*|) and the phase angle (δ) at different testing temperatures and loading frequencies were analyzed in this paper. Further, the dynamic modulus and the stiffness parameter (|E*|/sinδ) at the loading frequency of 10 Hz and testing temperature of 50 °C were illustrated. Simultaneously, the master curves of the dynamic modulus and phase angle of asphalt mixtures under different testing conditions were constructed to better investigate the effects of asphalt migration on the dynamic modulus by means of Williams–Landel–Ferry (WLF) equation and Sigmoidal function. Results show that, after the asphalt migration, the dynamic modulus of asphalt mixtures increase with the increasing loading frequency while they decrease with the increasing testing temperature; the dynamic modulus and the stiffness parameter are the highest when asphalt mixtures have the optimum asphalt content layers, and then decrease with the incremental difference of asphalt content in the upper and lower half portions. Besides this, different from the master curves of dynamic modulus, the master curves of phase angle firstly increase with the increase of loading frequency to the highest point and then decrease with the further increase of loading frequency and are not as smooth as that of dynamic modulus. It can be concluded that the asphalt migration has compromised the mixture’s mechanical structure, and the more asphalt migrates, the weaker the mechanical properties of asphalt mixture will be. Additionally, based on the shift factors and master curves in the time–temperature superposition principle (TTSP), the effects of asphalt migration on the dynamic modulus and the variation laws of the dynamic modulus of asphalt mixture after the occurrence of asphalt migration can be better construed at the quantitative level.

Master Curves of Dynamic Modulus and Phase Angle for High Modulus Asphalt Mixtures

2011 ◽  
Vol 243-249 ◽  
pp. 4226-4230
Author(s):  
Li Tao Geng ◽  
Rui Bo Ren ◽  
Li Zhi Wang ◽  
Cui Lan Gao
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Superposition Principle ◽  
Asphalt Mixture ◽  
Performance Testing ◽  
Temperature Shift ◽  
Asphalt Mixtures ◽  
Least Square ◽  
High Modulus ◽  
Master Curves

Two types of high modulus asphalt mixtures are introduced. Dynamic modulus and phase angle of these two mixtures are tested with Simple Performance Testing System under different temperatures, loading frequencies and confining pressures. Based on time-temperature superposition principle, dynamic modulus master curves and time-temperature shift factors at reference temperature are obtained using nonlinear square least square regression, and phase angle master curves are constructed utilizing the same time-temperature shift factors. The influence of confining pressure on mechanical properties of high modulus asphalt mixture is discussed.

Dynamic Modulus Characteristic of Large Stone Permeable Asphalt Mixtures

2013 ◽  
Vol 423-426 ◽  
pp. 1110-1113
Author(s):  
Jin Cheng Wei ◽  
Jin Li
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Asphalt Mixtures ◽  
Sigmoidal Function ◽  
Master Curves ◽  
Low Frequencies ◽  
High Frequencies ◽  
Modified Asphalt ◽  
Large Stone ◽  
Dynamic Modulus Test

To study the dynamic modulus characteristic of LSPM mixes, dynamic modulus test was conducted for Large Stone Permeable Asphalt Mixtures (LSPM ) with neat asphalt and with modified asphalt and the range of dynamic modulus values for LSPM was determined and the dynamic modulus master curves were developed. The magnitude of the dynamic modulus decreased with an increase in temperature and increased with an increase in the frequency. The phase angle decreased as the frequency increased at low temperature. With temperature increase, there was a transition interval, where the phase angle increased up to frequencies of 0.5 Hz, and then it started to decrease as frequency increased. After the transition interval, the phase angle increased with an increase in frequency. Master curves developed by sigmoidal function showed that LSPM with modified asphalt exhibited higher dynamic modulus values at middle and high frequencies and lower dynamic modulus values at low frequencies.

Study on the Viscoelastic Performance of Asphalt Mixture Based on Dynamic Modulus

2013 ◽  
Vol 753-755 ◽  
pp. 728-733 ◽  
Author(s):  
Teng Wang ◽  
Jun Tao Lin ◽  
Ling Pang ◽  
Min Lei ◽  
Kim Jenkins ◽  
...  
Keyword(s):  
Dynamic Modulus ◽  
Equivalence Principle ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Master Curves ◽  
Wlf Equation ◽  
Sigmoidal Model ◽  
Cam Model

The fitting models of dynamic modulus of asphalt mixtures were studied in this paper. UTM dynamic modulus tests were adopted to determine the dynamic modulus of two asphalt (A, B) mixtures. Then, the WLF equation and Arrhenius formula, based on the time-temperature equivalence principle, were used to get the shift factors and master curves of asphalt mixtures. Combined with Sigmoidal model and CAM model, it was founded that the Arrhenius formula was more suitable to get the master curves of asphalt mixtures. What is more, the CAM model was more suitable to fit master curves of both asphalt mixtures.

Experimental Analysis of Dynamic Modulus and Phase Angle of High Modulus Asphalt Mixture

2011 ◽  
Vol 243-249 ◽  
pp. 4220-4225
Author(s):  
Rui Bo Ren ◽  
Li Tao Geng ◽  
Li Zhi Wang ◽  
Peng Wang
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Asphalt Mixture ◽  
Performance Testing ◽  
Asphalt Mixtures ◽  
Testing System ◽  
High Modulus ◽  
Temperature Performance ◽  
Different Temperatures ◽  
Confining Pressures

To study the mechanical properties of high modulus asphalt mixtures, dynamic modulus and phase angle of these two mixtures are tested with Simple Performance Testing System under different temperatures, loading frequencies and confining pressures. Testing results show the superiority of high modulus asphalt mixture in aspect of high temperature performance. Furthermore, the changing rules of dynamic modulus and phase angle are also discussed.

Characteristic Analysis of Dynamic Modulus for High Modulus Asphalt Concrete

2014 ◽  
Vol 505-506 ◽  
pp. 15-18 ◽  
Author(s):  
Xiao Long Zou ◽  
Ai Min Sha ◽  
Wei Jiang ◽  
Xin Yan Huang
Keyword(s):  
Dynamic Modulus ◽  
Testing Machine ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
High Modulus ◽  
Characteristic Analysis ◽  
Modified Asphalt ◽  
Universal Testing ◽  
Different Temperatures ◽  
Dynamic Modulus Test

In order to analyze the characteristics of high modulus asphalt mixture dynamic modulus, Universal Testing Machine (UTM-25) was used for dynamic modulus test of three kinds of mixtures, which were PR Module modified asphalt mixture and PR PLAST.S modified asphalt mixture and virgin asphalt mixture, to investigate dynamic modulus and phase angle at different temperatures and frequencies. The results indicate that: the dynamic modulus order of the three asphalt mixtures is PR MODULE > PR PLAST.S > Virgin. PR MODULE asphalt mixture dynamic modulus is much larger than the other two.

Effect of Temperature on Phase Angle and Dynamic Modulus of Asphalt Mixtures Using SPT

2020 ◽  
Vol 1007 ◽  
pp. 99-104
Author(s):  
Juraidah Ahmad ◽  
Mohd Rosli Hainin ◽  
Ekarizan Shaffie ◽  
Khairil Azman Masri ◽  
Mohd Amin Shaffi
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Performance Test ◽  
Complex Modulus ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Load Resistance ◽  
Asphalt Mixtures ◽  
Effect Of Temperature ◽  
Low Viscosity

The Simple Performance Test (SPT) can be used to characterize the strength and load resistance of asphalt mixtures. The objectives of this study are to determine the effect of temperature on the phase angle and dynamic complex modulus of the asphalt mixtures tested at 30°C, 35°C, 40°C, 45°C and 50°C at 25Hz, 20Hz, 10Hz, 5Hz, 1Hz and 0.5Hz frequencies. The asphalt mixtures of NMAS 12.5mm are prepared using asphalt binder PEN 80/100 and PEN 60/70. The asphalt mixtures are designed using the Superpave system and compacted using the Superpave Gyratory Compactor (SGC). The dynamic modulus test results showed that at a higher temperature, the stiffness of the asphalt mixtures is affected. The dynamic modulus of the mixtures is highest at 30°C and gradually decrease at 35°C, 40°C, 45°C and 50°C respectively. The dynamic modulus values for asphalt mixtures with bitumen grade PEN 60/70 are also higher compared to the asphalt mixtures with bitumen grade PEN 80/100. Results also showed that the low phase angle values indicate low viscosity of the asphalt binder due to increase in temperature. The present study is meaningful in understanding the asphalt mixture behaviour at different temperature and loading frequencies.

Sign in / Sign up

Export Citation Format

Share Document