Effect of Additives and Aging on the Rheological Properties of Water-Based Drilling Fluid

1991 ◽  
Vol 13 (3) ◽  
pp. 369-387 ◽  
Author(s):  
PRAMOD KUMAR SINGH ◽  
V.P. SHARMA
Keyword(s):  
Rheological Properties ◽  
Drilling Fluid ◽  
Effect Of Additives ◽  
Water Based

Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Arild Saasen
Keyword(s):  
Rheological Properties ◽  
Pressure Loss ◽  
Drilling Fluid ◽  
Axial Flow ◽  
Drilling Fluids ◽  
Unstable Flow ◽  
Pressure Losses ◽  
Shear Dependent Viscosity ◽  
Water Based ◽  
Dependent Viscosity

Controlling the annular frictional pressure losses is important in order to drill safely with overpressure without fracturing the formation. To predict these pressure losses, however, is not straightforward. First of all, the pressure losses depend on the annulus eccentricity. Moving the drillstring to the wall generates a wider flow channel in part of the annulus which reduces the frictional pressure losses significantly. The drillstring motion itself also affects the pressure loss significantly. The drillstring rotation, even for fairly small rotation rates, creates unstable flow and sometimes turbulence in the annulus even without axial flow. Transversal motion of the drillstring creates vortices that destabilize the flow. Consequently, the annular frictional pressure loss is increased even though the drilling fluid becomes thinner because of added shear rate. Naturally, the rheological properties of the drilling fluid play an important role. These rheological properties include more properties than the viscosity as measured by API procedures. It is impossible to use the same frictional pressure loss model for water based and oil based drilling fluids even if their viscosity profile is equal because of the different ways these fluids build viscosity. Water based drilling fluids are normally constructed as a polymer solution while the oil based are combinations of emulsions and dispersions. Furthermore, within both water based and oil based drilling fluids there are functional differences. These differences may be sufficiently large to require different models for two water based drilling fluids built with different types of polymers. In addition to these phenomena washouts and tool joints will create localised pressure losses. These localised pressure losses will again be coupled with the rheological properties of the drilling fluids. In this paper, all the above mentioned phenomena and their consequences for annular pressure losses will be discussed in detail. North Sea field data is used as an example. It is not straightforward to build general annular pressure loss models. This argument is based on flow stability analysis and the consequences of using drilling fluids with different rheological properties. These different rheological properties include shear dependent viscosity, elongational viscosity and other viscoelastic properties.

scholarly journals Comparative Analysis of the Effect of Barite and Hematite on the Rheology of Water-Based Drilling Mud

2021 ◽  
Vol 1 (2) ◽  
Author(s):  
Osei H
Keyword(s):  
Rheological Properties ◽  
Drilling Fluid ◽  
Attrition Rate ◽  
Drilling Mud ◽  
Cleaning Efficiency ◽  
Drilling Operation ◽  
Water Based ◽  
Petroleum Resources ◽  
Drilling Muds ◽  
The Impact

High demand for oil and gas has led to exploration of more petroleum resources even at remote areas. The petroleum resources are found in deeper subsurface formations and drilling into such formations requires a well-designed drilling mud with suitable rheological properties in order to avoid or reduce associated drilling problems. This is because rheological properties of drilling muds have considerable effect on the drilling operation and cleaning of the wellbore. Mud engineers therefore use mud additives to influence the properties and functions of the drilling fluid to obtain the desired drilling mud properties especially rheological properties. This study investigated and compared the impact of barite and hematite as weighting agents for water-based drilling muds and their influence on the rheology. Water-based muds of different concentrations of weighting agents (5%, 10%, 15% and 20% of the total weight of the drilling mud) were prepared and their rheological properties determined at an ambient temperature of 24ᵒC to check their impact on drilling operation. The results found hematite to produce higher mud density, plastic viscosity, gel strength and yield point when compared to barite at the same weighting concentrations. The higher performance of the hematite-based muds might be attributed to it having higher specific gravity, better particle distribution and lower particle attrition rate and more importantly being free from contaminants. The water-based muds with hematite will therefore be more promising drilling muds with higher drilling and hole cleaning efficiency than those having barite.

Development of New Models to Determine the Rheological Parameters of Water-based Drilling Fluid Using Artificial Intelligence

2021 ◽  
Author(s):  
Farqad Hadi ◽  
Ali Noori ◽  
Hussein Hussein ◽  
Ameer Khudhair
Keyword(s):  
Rheological Properties ◽  
High Performance ◽  
Drilling Fluid ◽  
Gel Strength ◽  
Solid Content ◽  
Rheological Parameters ◽  
Water Based ◽  
Fluid Properties ◽  
Drilling Operations ◽  
Marsh Funnel

Abstract It is well known that drilling fluid is a key parameter for optimizing drilling operations, cleaning the hole, and managing the rig hydraulics and margins of surge and swab pressures. Although the experimental works present valid and reliable results, they are expensive and time consuming. On the other hand, continuous and regular determination of the rheological mud properties can perform its essential functions during well construction. More uncertainties in planning the drilling fluid properties meant that more challenges may be exposed during drilling operations. This study presents two predictive techniques, multiple regression analysis (MRA) and artificial neural networks (ANNs), to determine the rheological properties of water-based drilling fluid based on other simple measurable properties. While mud density (MW), marsh funnel (MF), and solid% are key input parameters in this study, the output functions or models are plastic viscosity (PV), yield point (YP), apparent viscosity (AV), and gel strength. The prediction methods were demonstrated by means of a field case in eastern Iraq, using datasets from daily drilling reports of two wells in addition to the laboratory measurements. To test the performance ability of the developed models, two error-based metrics (determination coefficient R2 and root mean square error RMSE) have been used in this study. The current results of this study support the evidence that MW, MF, and solid% are consistent indexes for the prediction of rheological properties. Both mud density and solid content have a relative-significant effect on increasing PV, YP, AV, and gel strength. However, a scattering around each fit curve is observed which proved that one rheological property alone is not sufficient to estimate other properties. The results also reveal that both MRA and ANN are conservative in estimating the fluid rheological properties, but ANN is more precise than MRA. Eight empirical mathematical models with high performance capacity have been developed in this study to determine the rheological fluid properties based on simple and quick equipment as mud balance and marsh funnel. This study presents cost-effective models to determine the rheological fluid properties for future well planning in Iraqi oil fields.

Method and Mechanism of Regulating Rheological Properties of Water-Based Drilling Fluid by High-Frequency and High-Voltage Alternating Current Electric Field

SPE Journal ◽  
2020 ◽  
Vol 25 (05) ◽  
pp. 2220-2233
Author(s):  
Weian Huang ◽  
Ming Lei ◽  
Jingwen Wang ◽  
Kaihe Lv ◽  
Lin Jiang ◽  
...  
Keyword(s):  
Electric Field ◽  
Rheological Properties ◽  
High Voltage ◽  
High Frequency ◽  
Pulse Width ◽  
Drilling Fluid ◽  
Width Ratio ◽  
Drilling Fluids ◽  
Water Based ◽  
Bentonite Suspension

Summary The rheology of drilling fluid is commonly regulated by chemical methods. In this work, a physical method of a high-frequency and high-voltage alternating current (AC) electric field to regulate the rheological properties of water-based drilling fluid is established. The effects of the electric field on the continuous phase and dispersed phase, as well as two kinds of water-based drilling fluids, were investigated, and the response relationship among rheological properties modeled by Bingham and Herschel-Bulkley (H-B) models and electric-field parameters was explored. Results showed that water conductivity increased when voltage reached 4 kV, whereas it was restored to the original state after 3 hours in the absence of an electric field, showing a memory effect. The effect was also observed on bentonite suspension, whose plastic viscosity increased with the aid of an electric field and decreased over time. Voltage showed the greatest effect on bentonite-suspension viscosity, followed by frequency and pulse-width ratio. Under the condition of voltage of 5 kV, frequency of 5 kHz, and pulse-width ratio of 80%, there was a maximum increase of 50% in viscosity. The addition of salts caused bentonite-suspension flocculation, and electric field reduced the consistency coefficient and relieved flocculation state. When polymers were incorporated in bentonite suspension, the electric field could decrease the adsorption amount between clay particles and polymeric additives such as amphoteric and acrylamide-based polymers. For two typical drilling fluids, the voltage of an introduced electric field was the main controlling factor to change the rheological properties; their plastic viscosity and consistency coefficient both started to increase when voltage reached 4 kV.

Rheological Properties of Barite Sediments in Water-Based Drilling Fluids

2018 ◽  
Author(s):  
Torbjørn Vrålstad ◽  
Ragnhild Skorpa ◽  
Arild Saasen
Keyword(s):  
Rheological Properties ◽  
Drilling Fluid ◽  
Gravity Separation ◽  
Drilling Fluids ◽  
Water Based ◽  
Different Types ◽  
Preliminary Study ◽  
Well Abandonment

When a drilling fluid column remains static over a timeframe of several years, the drilling fluid separates into different sediment phases due to gravity separation. These heavy sediments, entitled “settled barite”, are the cause of significant operational problems several years after drilling. An important problem caused by settled barite occurs when performing casing cut-and-pull operations during slot recovery and well abandonment: the casing is “stuck” due to the sediments in the annulus outside the casing. The consistency and rheological properties of the sediments determine how easily the casing is removed. In this paper, we report a preliminary study were we have artificially prepared gravity sediment phases for two different types of water-based drilling fluids; one KCl/polymer-based fluid and one bentonite-based fluid. By studying the rheological properties of the obtained sediment phases, we see that there are considerable differences between the sediments for these different drilling fluids.

scholarly journals A Combined Barite–Ilmenite Weighting Material to Prevent Barite Sag in Water-Based Drilling Fluid

Materials ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 1945 ◽  
Author(s):  
Salem Basfar ◽  
Abdelmjeed Mohamed ◽  
Salaheldin Elkatatny ◽  
Abdulaziz Al-Majed
Keyword(s):  
Rheological Properties ◽  
Base Fluid ◽  
Drilling Fluid ◽  
Fluid Density ◽  
Fluid Filtration ◽  
Dynamic Conditions ◽  
Filtration Performance ◽  
Water Based ◽  
Static Conditions ◽  
The Impact

Barite sag is a serious problem encountered while drilling high-pressure/high-temperature (HPHT) wells. It occurs when barite particles separate from the base fluid leading to variations in drilling fluid density that may cause a serious well control issue. However, it occurs in vertical and inclined wells under both static and dynamic conditions. This study introduces a combined barite–ilmenite weighting material to prevent the barite sag problem in water-based drilling fluid. Different drilling fluid samples were prepared by adding different percentages of ilmenite (25, 50, and 75 wt.% from the total weight of the weighting agent) to the base drilling fluid (barite-weighted). Sag tendency of the drilling fluid samples was evaluated under static and dynamic conditions to determine the optimum concentration of ilmenite which was required to prevent the sag issue. A static sag test was conducted under both vertical and inclined conditions. The effect of adding ilmenite to the drilling fluid was evaluated by measuring fluid density and pH at room temperature, and rheological properties at 120 °F and 250 °F. Moreover, a filtration test was performed at 250 °F to study the impact of adding ilmenite on the drilling fluid filtration performance and sealing properties of the formed filter cake. The results of this study showed that adding ilmenite to barite-weighted drilling fluid increased fluid density and slightly reduced the pH within the acceptable pH range (9–11). Ilmenite maintained the rheology of the drilling fluid with a minimal drop in rheological properties due to the HPHT conditions, while a significant drop was observed for the base fluid (without ilmenite). Adding ilmenite to the base drilling fluid significantly reduced sag factor and 50 wt.% ilmenite was adequate to prevent solids sag in both dynamic and static conditions with sag factors of 0.33 and 0.51, respectively. Moreover, HPHT filtration results showed that adding ilmenite had no impact on filtration performance of the drilling fluid. The findings of this study show that the combined barite–ilmenite weighting material can be a good solution to prevent solids sag issues in water-based fluids; thus, drilling HPHT wells with such fluids would be safe and effective.

scholarly journals Influence of Graphene Nanoplatelet and Silver Nanoparticle on the Rheological Properties of WaterBased Mud †

2018 ◽  
Vol 8 (8) ◽  
pp. 1386 ◽  
Author(s):  
Hazlina Husin ◽  
Khaled Abdalla Elraies ◽  
Hyoung Jin Choi ◽  
Zachary Aman
Keyword(s):  
Rheological Properties ◽  
Silver Nanoparticle ◽  
Drilling Fluid ◽  
Oil Field ◽  
Fluid Loss ◽  
Drilling Mud ◽  
Fluid System ◽  
Graphene Nanoplatelet ◽  
Environmental Friendly ◽  
Water Based

Water-based mud is known as an environmental-friendly drilling fluid system. The formulation of water-based mud is designed to have specific rheological properties under specific oil field conditions. In this study, graphene nanoplatelet and silver nanoparticle (nanosilver) were added to a water-based mud formulation in which they act as drilling mud additives. Rheological properties measurements and filtration tests were conducted for evaluating the influence of the added nanoparticles. The results showed that the graphene nanoplatelet and the nanosilver increased the plastic viscosity (PV) by up to 89.2% and 64.2%, respectively. Meanwhile, both the yield point (YP) and the fluid loss values were reduced. In addition, we believe this is the first result ever report where nanosilver is utilized for enhancing-enhanced water-based mud’s performance.

Sign in / Sign up

Export Citation Format

Share Document