Feasibility of gamma emission tomography for safeguard verification of fuel assemblies

2020 ◽  
Vol 175 (9-10) ◽  
pp. 779-790
Author(s):  
S. M. Motevalli ◽  
A. Payani
2021 ◽  
Vol 7 ◽  
Author(s):  
Peter Jansson

An idea is presented in which passive gamma emission tomography of irradiated nuclear fuel is developed to enable quantitative information of the spatial activity distribution of selected isotopes within the fuel rods of the assembly. The idea is based on using well-known calibration sources mounted in the measurement device during measurement. The image reconstruction would include the sources, thereby enable quantification of the activity distribution. Should the idea be proven viable, the outcome would be valuable to the global community dealing with characterisation of nuclear fuel in terms of safety, security, safeguards and fuel development.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ming Fang ◽  
Yoann Altmann ◽  
Daniele Della Latta ◽  
Massimiliano Salvatori ◽  
Angela Di Fulvio

AbstractCompliance of member States to the Treaty on the Non-Proliferation of Nuclear Weapons is monitored through nuclear safeguards. The Passive Gamma Emission Tomography (PGET) system is a novel instrument developed within the framework of the International Atomic Energy Agency (IAEA) project JNT 1510, which included the European Commission, Finland, Hungary and Sweden. The PGET is used for the verification of spent nuclear fuel stored in water pools. Advanced image reconstruction techniques are crucial for obtaining high-quality cross-sectional images of the spent-fuel bundle to allow inspectors of the IAEA to monitor nuclear material and promptly identify its diversion. In this work, we have developed a software suite to accurately reconstruct the spent-fuel cross sectional image, automatically identify present fuel rods, and estimate their activity. Unique image reconstruction challenges are posed by the measurement of spent fuel, due to its high activity and the self-attenuation. While the former is mitigated by detector physical collimation, we implemented a linear forward model to model the detector responses to the fuel rods inside the PGET, to account for the latter. The image reconstruction is performed by solving a regularized linear inverse problem using the fast-iterative shrinkage-thresholding algorithm. We have also implemented the traditional filtered back projection (FBP) method based on the inverse Radon transform for comparison and applied both methods to reconstruct images of simulated mockup fuel assemblies. Higher image resolution and fewer reconstruction artifacts were obtained with the inverse-problem approach, with the mean-square-error reduced by 50%, and the structural-similarity improved by 200%. We then used a convolutional neural network (CNN) to automatically identify the bundle type and extract the pin locations from the images; the estimated activity levels finally being compared with the ground truth. The proposed computational methods accurately estimated the activity levels of the present pins, with an associated uncertainty of approximately 5%.


2019 ◽  
Vol 66 (1) ◽  
pp. 487-496
Author(s):  
Camille Belanger-Champagne ◽  
Pauli Peura ◽  
Paula Eerola ◽  
Tapani Honkamaa ◽  
Timothy White ◽  
...  

2021 ◽  
Vol 7 (10) ◽  
pp. 212
Author(s):  
Ahmed Karam Eldaly ◽  
Ming Fang ◽  
Angela Di Fulvio ◽  
Stephen McLaughlin ◽  
Mike E. Davies ◽  
...  

In this paper, we address the problem of activity estimation in passive gamma emission tomography (PGET) of spent nuclear fuel. Two different noise models are considered and compared, namely, the isotropic Gaussian and the Poisson noise models. The problem is formulated within a Bayesian framework as a linear inverse problem and prior distributions are assigned to the unknown model parameters. In particular, a Bernoulli-truncated Gaussian prior model is considered to promote sparse pin configurations. A Markov chain Monte Carlo (MCMC) method, based on a split and augmented Gibbs sampler, is then used to sample the posterior distribution of the unknown parameters. The proposed algorithm is first validated by simulations conducted using synthetic data, generated using the nominal models. We then consider more realistic data simulated using a bespoke simulator, whose forward model is non-linear and not available analytically. In that case, the linear models used are mis-specified and we analyse their robustness for activity estimation. The results demonstrate superior performance of the proposed approach in estimating the pin activities in different assembly patterns, in addition to being able to quantify their uncertainty measures, in comparison with existing methods.


2020 ◽  
Vol 2 (2) ◽  
Author(s):  
Peter Andersson ◽  
Vikram Rathore ◽  
Lorenzo Senis ◽  
Anastasios Anastasiadis ◽  
Erik Andersson Sundén ◽  
...  

Author(s):  
Mikhail Mayorov ◽  
Timothy White ◽  
Alain Lebrun ◽  
Joerg Brutscher ◽  
Jens Keubler ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document