Tribological Analysis and Characterization of Zinc Rich Al/Si3N4 Composites Fabricated Via Ultrasonic Assisted Stir Casting Technique

2021 ◽  
pp. 1-13
Author(s):  
Ashish Purohit ◽  
Ravindra Singh Kumar ◽  
Rajesh Rana
Keyword(s):  
Stir Casting ◽  
Casting Technique ◽  
Ultrasonic Assisted ◽  
Tribological Analysis ◽  
Ultrasonic Assisted Stir Casting

Mechanical characterization of LM25 alloy matrix composite reinforced with boron carbide

2021 ◽  
pp. 002199832110055
Author(s):  
Zeeshan Ahmad ◽  
Sabah Khan
Keyword(s):  
Tensile Strength ◽  
Boron Carbide ◽  
Mechanical Characterization ◽  
Stir Casting ◽  
Surface Mapping ◽  
Alloy Matrix ◽  
Casting Technique ◽  
The Matrix ◽  
Carbide Particles

Alumnium alloy LM 25 based composites reinforced with boron carbide at different weight fractions of 4%, 8%, and 12% were fabricated by stir casting technique. The microstructures and morphology of the fabricated composites were studied by scanning electron microscopy and energy dispersive spectroscopy. Elemental mapping of all fabricated composites were done to demonstrate the elements present in the matrix and fabricated composites. The results of microstructural analyses reveal homogenous dispersion of reinforcement particles in the matrix with some little amount of clustering found in composites reinforced with 12% wt. of boron carbide. The mechanical characterization is done for both alloy LM 25 and all fabricated composites based on hardness and tensile strength. The hardness increased from 13.6% to 21.31% and tensile strength 6.4% to 22.8% as reinforcement percentage of boron carbide particles increased from 0% to 12% wt. A fractured surface mapping was also done for all composites.

New Emerging Al7075 Based Hybrid Nanocomposite for Automotive Applications: A Sustainability Approach

2020 ◽  
Vol 856 ◽  
pp. 29-35
Author(s):  
Sweety Mahanta ◽  
M. Chandrasekaran ◽  
Sutanu Samanta
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Hybrid Composites ◽  
High Strength ◽  
Stir Casting ◽  
Automotive Application ◽  
Percentage Increase ◽  
Casting Technique ◽  
Ultrasonic Assisted Stir Casting ◽  
The Impact

Aluminium matrix composites (AMCs) have emerged as the substitute for the monolithic (unreinforced) materials over the past few decades. The applications of AMCs are common in automotive, aerospace, defence and biomedical sectors due to its lower weight, high strength, high resistance against corrosion and high thermal and electrical conductivity. In this work, it is aimed fabricate a new class Al 7075 based hybrid composites reinforcing with nanoparticulates suitable for automotive application. Al7075 reinforced with fixed quantity of boron carbide (B4C) (1.5 wt.%) and varying wt % of flyash (0.5 wt.%, 1.0 wt.%, 1.5 wt.%) is fabricated using ultrasonic-assisted stir casting technique. Physical and mechanical characterization such as density, porosity, micro hardness, tensile strength and impact strength were estimated for three different compositions. The tensile strength and percentage increase in hardness value of the nanocomposite Al7075-B4C (1.5 wt. %)-flyash (0.5 wt. %): HNC3 found maximum as 294 MPa and 32.93%. In comparison with Al7075 alloy the impact strength of HNC3 shows the highest percentage of 9.31% respectively.

scholarly journals Effect of addition of different reinforcements on the microstructure and mechanical characterization of the Al-Flyash composites

2021 ◽  
Vol 15 (56) ◽  
pp. 217-228
Author(s):  
Milind K. Wasekar ◽  
Mohan P. Khond
Keyword(s):  
Tensile Strength ◽  
Hybrid Composites ◽  
Tensile Tests ◽  
Stir Casting ◽  
Interface Bonding ◽  
Casting Technique ◽  
Testing Procedures ◽  
The Matrix ◽  
Aluminum 6061 Alloy

The aim of this work is to investigate the influence of the addition of silicon carbide and molybdenum disulfide on the microstructure and the tensile strength of the Al-Flyash hybrid composites prepared using the stir casting technique. The composite with aluminum 6061 alloy as the matrix and flyash as the reinforcement, with different weight fractions, is investigated to study its microstructure and the tensile strength. The same has been compared with the hybrid composites with Aluminum-Flyash/SiC and Aluminum-Flyash/MoS2 for different weight fractions of the reinforcements. The tensile tests were conducted as per ASTM standard testing procedures at room temperature. From the results it is identified that tensile strength of the Al6061-Flyash composite is lesser than the Al6061-Flyash/SiC and Al6061-Flyash/MoS2 hybrid composites. It is also observed that increment in the composition of the SiC and MoS2 causes the increment in the tensile strength of the hybrid composite. This increment in the tensile strength is due to good interface bonding and uniform distribution of the reinforcements in the composite.

scholarly journals Characterization of AMCs Produced by Stir Casting Technique

2021 ◽  
Vol 1123 (1) ◽  
pp. 012006
Author(s):  
M Saleem ◽  
Nishant Kumar raj ◽  
Yogesh kumar ◽  
Pranav Kumar
Keyword(s):  
Stir Casting ◽  
Casting Technique
Sign in / Sign up

Export Citation Format

Share Document