scholarly journals Analysis on anti-corrosion and anti-scaling technology of water injection well in oil production plant

2020 ◽  
Vol 514 ◽  
pp. 022005
Author(s):  
Yuning Dong
Keyword(s):  
Water Injection ◽  
Oil Production ◽  
Injection Well ◽  
Production Plant

The Don Field, Blocks 211/13a, 211/14, 211/18a, 211/19a, UK North Sea

2003 ◽  
Vol 20 (1) ◽  
pp. 257-263
Author(s):  
A. D. Milne ◽  
A. M. Brown
Keyword(s):  
North Sea ◽  
Middle Jurassic ◽  
Water Injection ◽  
Oil Production ◽  
Injection Well ◽  
Northern North Sea

abstractCumulative oil production to the end of 2000 from the Don Field was 15.4 MMBBLS, which with an estimated STOIIP of 152 MMBBLS represents a recovery to date of 10%. Don has been producing for over ten years. The field lics 15 km N of the Thistle Field, at the western edge of the Viking Graven in the northern North Sea. The structure of the field is complex, and it comprises several segments, the two larges of which have been developed, Don NE and Don SW. The reservoir sequence is Middle Jurassic Brent Formation. But more deeply buried and of a more distal facies than is typical for other fields in the province.The Don Field is a sub-sea development tied-back to the Thistle platform, and Britoil (BP) is the operator. The field has been developed with five producers, three in NE andtwo is SW, with a supporting water injection well in each part of the field. All wells have been drill deviated from a seabed manifold located over Don NE.

scholarly journals Review of Absorption Oil Content in Water Injection

2020 ◽  
Author(s):  
Aditya Nugraha Ernawan ◽  
Alfi Fachrizal ◽  
Angga Wijaya ◽  
Bima Syahreza ◽  
Muhammad Ridwan Alkhandi ◽  
...  
Keyword(s):  
Oil Content ◽  
Oil And Gas ◽  
Produced Water ◽  
Economic Condition ◽  
Water Injection ◽  
Oil Production ◽  
Injection Well ◽  
Shaly Sand

Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

The Birch Field, Block 16/12a, UK North Sea

2003 ◽  
Vol 20 (1) ◽  
pp. 167-181 ◽  
Author(s):  
J. Hook ◽  
A. Abhvani ◽  
J. G. Gluyas ◽  
M. Lawlor
Keyword(s):  
Hanging Wall ◽  
Water Injection ◽  
Oil Production ◽  
Volatile Oil ◽  
Oil Field ◽  
Injection Well ◽  
Current Estimate ◽  
Oil Reserves ◽  
Water Cut ◽  
The Uk

AbstractThe Birch Field is an oil field located in Block 16/12a on the UK Continental Shelf (UKCS) and is part of the well-established 'Brae Trend'. Birch produces an undersaturated volatile oil from the Brae Conglomerate, a locally thick conglomeratic unit within the Late Jurassic Brae Formation. The reservoir was deposited as a small submarine fan in the hanging wall of the main fault bounding the western side of the South Viking Graben. The current estimate for oil in place is about 70MMSTB with expected ultimate oil reserves of 30MMSTB. The field was brought on stream in September 1995 as a phased waterflood subsea development, tied back to Marathon's Brae 'A' platform in neighbouring Block 16/7a. During Phase I the discovery and both appraisal wells were re-completed as two oil producers and one water injection well. Phase II comprised a third oil production well and a second water injection well drilled and completed in 1996-1997. Oil production peaked at c. 28 000 BOPD in the second half of 1996. The field is currently in decline and production in June 1999 was c. 7000 BOPD with a water-cut of c. 40%. Cumulative oil production to end June 1999 was 21 MM STB and remaining oil reserves are estimated as 9MMSTB.

A New Method of Fall-Off Test in Water Injection Well in Tahe Oilfield

2013 ◽  
Vol 807-809 ◽  
pp. 2508-2513
Author(s):  
Qiang Wang ◽  
Wan Long Huang ◽  
Hai Min Xu
Keyword(s):  
Water Injection ◽  
Injection Well ◽  
Well Test ◽  
Well Bore ◽  
Residual Oil ◽  
Injection Wells ◽  
Oil Saturation ◽  
Tahe Oilfield ◽  
Fitting Method ◽  
Front Radius

In pressure drop well test of the clasolite water injection well of Tahe oilfield, through nonlinear automatic fitting method in the multi-complex reservoir mode for water injection wells, we got layer permeability, skin factor, well bore storage coefficient and flood front radius, and then we calculated the residual oil saturation distribution. Through the examples of the four wells of Tahe oilfield analyzed by our software, we found that the method is one of the most powerful analysis tools.

The New Generation of Outflow Control Devices Autonomously Controlling the Conformance of Water Injection Well- A Case Study with ADNOC Onshore

2021 ◽  
Author(s):  
Sultan Ibrahim Al Shemaili ◽  
Ahmed Mohamed Fawzy ◽  
Elamari Assreti ◽  
Mohamed El Maghraby ◽  
Mojtaba Moradi ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Dynamic Properties ◽  
Short Circuit ◽  
Water Injection ◽  
Performance Outcomes ◽  
Injection Well ◽  
Well Performance ◽  
Injection Wells ◽  
Horizontal Section ◽  
Control Devices

Abstract Several techniques have been applied to improve the water conformance of injection wells to eventually improve field oil recovery. Standalone Passive flow control devices or these devices combined with Sliding sleeves have been successful to improve the conformance in the wells, however, they may fail to provide the required performance in the reservoirs with complex/dynamic properties including propagating/dilating fractures or faults and may also require intervention. This is mainly because the continuously increasing contrast in the injectivity of a section with the feature compared to the rest of the well causes diverting a great portion of the injected fluid into the thief zone which ultimately creates short-circuit to the nearby producer wells. The new autonomous injection device overcomes this issue by selectively choking the injection of fluid into the growing fractures crossing the well. Once a predefined upper flowrate limit is reached at the zone, the valves autonomously close. Well A has been injecting water into reservoir B for several years. It has been recognised from the surveys that the well passes through two major faults and the other two features/fractures with huge uncertainty around their properties. The use of the autonomous valve was considered the best solution to control the water conformance in this well. The device initially operates as a normal passive outflow control valve, and if the injected flowrate flowing through the valve exceeds a designed limit, the device will automatically shut off. This provides the advantage of controlling the faults and fractures in case they were highly conductive as compared to other sections of the well and also once these zones are closed, the device enables the fluid to be distributed to other sections of the well, thereby improving the overall injection conformance. A comprehensive study was performed to change the existing dual completion to a single completion and determine the optimum completion design for delivering the targeted rate for the well while taking into account the huge uncertainty around the faults and features properties. The retrofitted completion including 9 joints with Autonomous valves and 5 joints with Bypass ICD valves were installed in the horizontal section of the well in six compartments separated with five swell packers. The completion was installed in mid-2020 and the well has been on the injection since September 2020. The well performance outcomes show that new completion has successfully delivered the target rate. Also, the data from a PLT survey performed in Feb 2021 shows that the valves have successfully minimised the outflow toward the faults and fractures. This allows achieving the optimised well performance autonomously as the impacts of thief zones on the injected fluid conformance is mitigated and a balanced-prescribed injection distribution is maintained. This paper presents the results from one of the early installations of the valves in a water injection well in the Middle East for ADNOC onshore. The paper discusses the applied completion design workflow as well as some field performance and PLT data.

scholarly journals Economic Evaluation of Fiscal Regime on EOR Implementation in Indonesia: A Case Study of Low Salinity Water Injection on Field X

2020 ◽  
Vol 9 (1) ◽  
pp. 17-35
Author(s):  
Adityawarman Adityawarman ◽  
Faridh Afdhal Aziz ◽  
Prasandi Abdul Aziz ◽  
Purnomo Yusgiantoro ◽  
Steven Chandra
Keyword(s):  
Sensitivity Analysis ◽  
Net Present Value ◽  
Water Injection ◽  
Oil Production ◽  
Oil Price ◽  
Low Salinity ◽  
Low Salinity Water ◽  
Fiscal Regimes ◽  
Salinity Water ◽  
Low Salinity Water Injection

There are currently two fiscal regimes designated for resource allocation in Indonesia’s upstream oil and gas industry, the Production Sharing Contract Cost Recovery (PSC) and Gross Split. The Gross Split in the form of additional percentage split is designed to encourage contractors to implement Enhanced Oil Recovery (EOR) in mature fields. Low Salinity Water Injection (LSWI) is an emerging EOR technique in which the salinity of the injected water is controlled. It has been proven to be relatively cheaper and has simpler implementations than other EOR options in several countries. This study evaluates the LSWI project’s economy using PSC and Gross Split and then to be compared to conventional waterflooding (WF) project’s economy. There are four cases on Field X that are simulated using a commercial simulator for 5 years. The cases are evaluated under PSC and Gross Split to calculate the project’s economy. The economic indicators that will be evaluated are the Net Present Value (NPV) and sensitivity analysis is also conducted to observe the change of NPV. The parameters for sensitivity analysis are Capital Expenditure (CAPEX), Operating Expenditure (OPEX), Oil Production, and Oil Price. It is found that LSWI implementation using Gross Split is more profitable than PSC. The parameters that affects NPV the most in all PSC cases are the oil production and oil price. On the other hand, in Gross Split cases, the oil production is the parameter that affects NPV the most, followed by oil price. The novelty of this study is in the comparison of project’s economy between WF and LSWI using two different fiscal regimes to see whether Gross Split is more profitable than PSC on EOR implementation, specifically the LSWI at Field X.

An Integrated IR4.0 Software Enables Autonomous Casing Crossflow Rate Calculation

2021 ◽  
Author(s):  
Nasser M. Al-Hajri ◽  
Akram R. Barghouti ◽  
Sulaiman T. Ureiga
Keyword(s):  
Industrial Revolution ◽  
Water Injection ◽  
Flow Characteristics ◽  
Injection Rate ◽  
Performance Model ◽  
Injection Well ◽  
Production Model ◽  
Well Performance ◽  
Secondary Formation ◽  
Well Model

Abstract This paper will present an alternative calculation technique to predict wellbore crossflow rate in a water injection well resulting from a casing leak. The method provides a self-governing process for wellbore related calculations inspired by the fourth industrial revolution technologies. In an earlier work, calculations techniques were presented which do not require the conventional use of downhole flowmeter (spinner) to obtain the flow rate. Rather, continuous surface injection data prior to crossflow development and shut-in well are used to estimate the rate. In this alternative methodology, surface injection data post crossflow development are factored in to calculate the rate with the same accuracy. To illustrate the process an example water injector well is used. To quantify the casing leak crossflow rate, the following calculation methodology was applied:Generate a well performance model using pre-crossflow injection data. Normal modeling techniques are applied in this step to obtain an accurate model for the injection well as a baseline case.Generate an imaginary injection well model: An injection well mimicking the flow characteristics and properties of the water injector is envisioned to simulate crossflow at flowing (injecting) conditions. In this step, we simulate an injector that has total depth up to the crossflow location only and not the total depth of the example water well.Generate the performance model for the secondary formation using post crossflow data: The total injection rate measured at surface has two portions: one portion goes into the shallower secondary formation and another goes into the deeper (primary) formation. The modeling inputs from the first two steps will be used here to obtain the rate for the downhole formation at crossflow conditions.Generate an imaginary production well model: The normal model for the water injector will be inversed to obtain a production model instead. The inputs from previous steps will be incorporated in the inverse modeling.Obtaining the crossflow rate at shut-in conditions: Performance curves generated from step 3 & 4 will be plotted together to obtain an intersection that corresponds to the crossflow rate at shut-in conditions. This numerical methodology was analytically derived and the prediction results were verified on syntactic field data with very high accuracy. The application of this model will benefit oil operators by avoiding wireline logging costs and associated safety risks with mechanical intervention.

Baghdad and Erbil policy moves may deter oil investors

2021 ◽  
Keyword(s):  
Water Injection ◽  
Oil Production ◽  
Political Stability ◽  
Kurdistan Region ◽  
Content Type ◽  
Associated Gas ◽  
Oil Sector ◽  
Bureaucratic Reform

Significance Although some important hydrocarbons projects have seen progress, both Baghdad and Erbil have made fresh moves seen as prejudicial by oil sector investors. Uncertainty continues over the authorities’ commitment to contracts, while the Kurdistan region has yet again fallen behind on payments to oil firms. Impacts Increased oil production as OPEC+ limits ease will make progress on associated gas capture and water injection more urgent. A dire electricity situation may pose a threat to political stability. Uncertainties over the upcoming elections in October and poor prospects for bureaucratic reform may further deter investment.

Sign in / Sign up

Export Citation Format

Share Document