scholarly journals Influence of cooling rate on structure and combustion reactivity of char during char preparation process

2020 ◽  
Vol 615 ◽  
pp. 012072
Author(s):  
Huanying Chi ◽  
Sheng Su ◽  
Jun Xiang ◽  
Pengfeng Yu ◽  
Haizhou Huang ◽  
...  
Keyword(s):  
Cooling Rate ◽  
Preparation Process ◽  
Combustion Reactivity

The forming and crystallization behaviors of Zr50Ti5Cu27Ni10Al8 bulk amorphous alloy by laser additive manufacturing

2020 ◽  
Vol 10 (7) ◽  
pp. 1155-1160 ◽  
Author(s):  
Yaqiong Ge ◽  
Xin Chen ◽  
Zexin Chang
Keyword(s):  
Amorphous Alloy ◽  
Cooling Rate ◽  
Heat Affected Zone ◽  
Molten Pool ◽  
Amorphous Structure ◽  
Bulk Amorphous Alloy ◽  
Preparation Process ◽  
Laser Additive Manufacturing ◽  
Obvious Effect ◽  
Composition And Structure

Due to the small size and serious crystallization, the wider application of amorphous alloy materials is limited. In this paper, the bulk amorphous alloy with the size of 15 mm × 15 mm × 12 mm was made by selective laser melting technology. The characters of the composition and structure of the as-prepared bulk amorphous alloy and the thermal effect of the preparation process were analyzed. The results showed that the cooling rate of both the molten pool and the heat affected zone were much higher than the critical cooling rate of the amorphous alloy and, therefore, the cooling rate was not the reason for the crystallization in this experiment. The molten pool of the formed amorphous alloy block was completely amorphous. Due to the accumulation of structural relaxation, crystallization occurred in the heat affected zone, but the amorphous structure was still dominant. The increase in deposition layer had no obvious effect on crystallization.

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Suppression of γ’ Precipitation in a Laser-Melted Nickel-Base Alloy

1977 ◽  
Vol 35 ◽  
pp. 270-271
Author(s):  
J. M. Walsh ◽  
J. C. Whittles ◽  
B. H. Kear ◽  
E. M. Breinan
Keyword(s):  
Cooling Rate ◽  
Base Alloy ◽  
Material Surface ◽  
Intimate Contact ◽  
Absorbed Power ◽  
Perfect Contact ◽  
Nickel Base ◽  
Rapidly Solidified ◽  
Limiting Case ◽  
The Heat Transfer Coefficient

Conventionally cast γ’ precipitation hardened nickel-base superalloys possess well-defined dendritic structures and normally exhibit pronounced segregation. Splat quenched, or rapidly solidified alloys, on the other hand, show little or no evidence for phase decomposition and markedly reduced segregation. In what follows, it is shown that comparable results have been obtained in superalloys processed by the LASERGLAZE™ method.In laser glazing, a sharply focused laser beam is traversed across the material surface at a rate that induces surface localized melting, while avoiding significant surface vaporization. Under these conditions, computations of the average cooling rate can be made with confidence, since intimate contact between the melt and the self-substrate ensures that the heat transfer coefficient is reproducibly constant (h=∞ for perfect contact) in contrast to the variable h characteristic of splat quenching. Results of such computations for pure nickel are presented in Fig. 1, which shows that there is a maximum cooling rate for a given absorbed power density, corresponding to the limiting case in which melt depth approaches zero.

Voids in Quenched Nickel

1968 ◽  
Vol 26 ◽  
pp. 266-267
Author(s):  
J. J. Laidler
Keyword(s):  
Electron Beam ◽  
Ambient Temperature ◽  
Cooling Rate ◽  
Three Dimensional ◽  
Cooling Curve ◽  
Polycrystalline Nickel ◽  
Quenching Temperature ◽  
Long Tail ◽  
Diffusion Pump

The presence of three-dimensional voids in quenched metals has long been suspected, and voids have indeed been observed directly in a number of metals. These include aluminum, platinum, and copper, silver and gold. Attempts at the production of observable quenched-in defects in nickel have been generally unsuccessful, so the present work was initiated in order to establish the conditions under which such defects may be formed.Electron beam zone-melted polycrystalline nickel foils, 99.997% pure, were quenched from 1420°C in an evacuated chamber into a bath containing a silicone diffusion pump fluid . The pressure in the chamber at the quenching temperature was less than 10-5 Torr . With an oil quench such as this, the cooling rate is approximately 5,000°C/second above 400°C; below 400°C, the cooling curve has a long tail. Therefore, the quenched specimens are aged in place for several seconds at a temperature which continuously approaches the ambient temperature of the system.

Microstructures of Laser Processed Fe-Cr Surface Alloys

1981 ◽  
Vol 39 ◽  
pp. 328-329
Author(s):  
P. A. Molian ◽  
K. H. Khan ◽  
W. E. Wood
Keyword(s):  
Cooling Rate ◽  
Pure Iron ◽  
Continuous Wave ◽  
Laser Surface ◽  
Material Surface ◽  
Constitution Diagram ◽  
Incident Power ◽  
Surface Alloying ◽  
Laser Surface Alloying ◽  
Spot Diameter

In recent years, the effects of chromium on the transformation characteristics of pure iron and the structures produced thereby have been extensively studied as a function of cooling rate. In this paper, we present TEM observations made on specimens of Fe-10% Cr and Fe-20% Cr alloys produced through laser surface alloying process with an estimated cooling rate of 8.8 x 104°C/sec. These two chromium levels were selected in order to study their phase transformation characteristics which are dissimilar in the two cases as predicted by the constitution diagram. Pure iron (C<0.01%, Si<0.01%, Mn<0.01%, S=0.003%, P=0.008%) was electrodeposited with chromium to the thicknesses of 40 and 70μm and then vacuum degassed at 400°F to remove the hydrogen formed during electroplating. Laser surface alloying of chromium into the iron substrate was then performed employing a continuous wave CO2 laser operated at an incident power of 1200 watts. The laser beam, defocussed to a spot diameter of 0.25mm, scanned the material surface at a rate of 30mm/sec, (70 ipm).

An Improved Method for the Preparation and TEM Examination of Sharp Pointed Tips used in APFIM and STM

1990 ◽  
Vol 48 (2) ◽  
pp. 102-103
Author(s):  
E.A. Fischione ◽  
P.E. Fischione ◽  
J.J. Haugh ◽  
M.G. Burke
Keyword(s):  
Atom Probe ◽  
Preparation Process ◽  
Improved Method ◽  
Ion Milling ◽  
Polishing Process ◽  
Probe Field ◽  
Scanning Tunnelling ◽  
Stm Tips ◽  
Tunnelling Microscopy ◽  
Ion Microscopy

A common requirement for both Atom Probe Field-Ion Microscopy (APFIM) and Scanning Tunnelling Microscopy (STM) is a sharp pointed tip for use as either the specimen (APFIM) or the probe (STM). Traditionally, tips have been prepared by either chemical or electropolishing techniques. Recently, ion-milling has been successfully employed in the production of APFIM tips [1]. Conventional electropolishing techniques are applicable to a wide variety of metals, but generally require careful manual adjustments during the polishing process and may also be time-consuming. In order to reduce the time and effort involved in the preparation process, a compact, self-contained polishing unit has been developed. This system is based upon the conventional two-stage electropolishing technique in which the specimen/tip blank is first locally thinned or “necked”, and subsequently electropolished until separation occurs.[2,3] The result of this process is the production of two APFIM or STM tips. A mechanized polishing unit that provides these functions while automatically maintaining alignment has been designed and developed.

Sign in / Sign up

Export Citation Format

Share Document