scholarly journals Effects of alkanolamide loading on swelling, rheometric and tensile properties of chloroprene rubber compounds

2018 ◽  
Vol 309 ◽  
pp. 012104 ◽  
Author(s):  
I Surya ◽  
H Ismail
Keyword(s):  
Tensile Properties ◽  
Rubber Compounds ◽  
Chloroprene Rubber

scholarly journals Rheometer Evidences for the Co-Curing Effect of a Bismaleimide in Conjunction with the Accelerated Sulfur on Natural Rubber/Chloroprene Rubber Blends

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1510
Author(s):  
Marek Pöschl ◽  
Shibulal Gopi Sathi ◽  
Radek Stoček ◽  
Ondřej Kratina
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Crosslinking Agent ◽  
Alder Reaction ◽  
Diels Alder ◽  
Ene Reactions ◽  
Rubber Blends ◽  
Diels Alder Reaction ◽  
Chloroprene Rubber

The rheometer curing curves of neat natural rubber (NR) and neat chloroprene rubber (CR) with maleide F (MF) exhibit considerable crosslinking torque at 180 °C. This indicates that MF can crosslink both these rubbers via Alder-ene reactions. Based on this knowledge, MF has been introduced as a co-crosslinking agent for a 50/50 blend of NR and CR in conjunction with accelerated sulfur. The delta (Δ) torque obtained from the curing curves of a blend with the addition of 1 phr MF was around 62% higher than those without MF. As the content of MF increased to 3 phr, the Δ torque was further raised to 236%. Moreover, the mechanical properties, particularly the tensile strength of the blend with the addition of 1 phr MF in conjunction with the accelerated sulfur, was around 201% higher than the blend without MF. The overall tensile properties of the blends cured with MF were almost retained even after ageing the samples at 70 °C for 72 h. This significant improvement in the curing torque and the tensile properties of the blends indicates that MF can co-crosslink between NR and CR via the Diels–Alder reaction.

scholarly journals The effects of alkanolamide addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR) / chloroprene rubber (CR) blends

2018 ◽  
Vol 34 ◽  
pp. 01030 ◽  
Author(s):  
Indra Surya ◽  
Syahrul Fauzi Siregar ◽  
Hanafi Ismail
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Crosslink Density ◽  
Tensile Modulus ◽  
Palm Stearin ◽  
Swelling Behaviour ◽  
Elongation At Break ◽  
Cure Characteristics ◽  
Chloroprene Rubber

Effects of alkanolamide (ALK) addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR)/chloroprene rubber (CR) blends were investigated. The ALK was synthesized from Refined Bleached Deodorized Palm Stearin (RBDPS) and diethanolamine, and incorporated into the silica-filled NR/CR blends as a non-toxic rubber additive. The ALK loadings were 0.0, 1.0, 3.0, 5.0 and 7.0 phr. It was found that the ALK exhibited shorter scorch and cure times and higher elongation at break of the silica-filled NR/CR blends. The ALK also exhibited higher torque differences, tensile modulus and tensile strength at a 1.0 phr of ALK loading and then decreased with further increases in the ALK loading. The swelling measurement proved that the 1.0 phr loading of ALK caused the highest degree in crosslink density of the silica-filled NR/CR blends.

Influence of different curing regimes on properties of new copolymer of chloroprene and acrylonitrile

2021 ◽  
pp. 009524432110386
Author(s):  
Mousumi De Sarkar ◽  
Takashi Sunada ◽  
Atsunori Kondo
Keyword(s):  
Stable State ◽  
Industrial Applications ◽  
Vital Role ◽  
Product Families ◽  
Compression Set ◽  
Rubber Compounds ◽  
Chloroprene Rubber ◽  
Ethylene Thiourea ◽  
Curing Regimes ◽  
Curing Systems

The curing system plays a vital role in designing rubber compounds for various industrial applications. Therefore, it is paramount to establish viable curing strategies for any new elastomer to explore its application potentials and commercial significance. Impacts of different curing regimes on the properties of a recently developed copolymer of chloroprene and acrylonitrile (acrylonitrile-chloroprene rubber, NCR) are reported here. Several primary accelerators (four from thiourea- and one from thiazolene product families) were used for curing the new rubber along with fixed loadings of zinc oxide (5 phr) and magnesium oxide (4 phr). Besides, curatives based on sulfur and peroxide were also evaluated. The influence of different curing systems on the rheological and physical properties of the copolymer was explored. It has been seen that the properties of the copolymer are considerably influenced by the different curing systems used. While ethylene thiourea (ETU) and propylene thiourea (PTU), as primary accelerators, provide the highest state of cure but may cause scorch. The use of trimethyl thiourea (TMU), on the other hand, results in the fastest rate and the most stable state of cure, good scorch safety, bin stability, and an overall good balance of properties. The sulfur-based crosslinking system induces good mechanical properties but causes limited bin stability, poor high-temperature compression set, and impaired heat resistance properties. As a curing agent, peroxide delivers the best bin stability in the rubber stocks but yields higher stiffness and limited aging resistance in the vulcanizates.

scholarly journals Cure characteristics, swelling behaviour and tensile properties of carbon black-filled Natural Rubber (NR)/Chloroprene Rubber (CR) blends in the presence of alkanolamide

2018 ◽  
Vol 197 ◽  
pp. 12005 ◽  
Author(s):  
Indra Surya ◽  
Mimpin Ginting ◽  
Hanafi Ismail
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Tensile Modulus ◽  
Palm Stearin ◽  
Swelling Behaviour ◽  
Blend Ratio ◽  
Elongation At Break ◽  
Cure Characteristics ◽  
Chloroprene Rubber

The cure characteristics, swelling behaviour and tensile properties of carbon black (CB)-filled natural rubber (NR)/chloroprene rubber (CR) blends in the presence of alkanolamide (ALK) were investigated. The NR/CR blends were prepared at 50/50 blend ratio. The ALK was prepared from Refined Bleached Deodorized Palm Stearin (RBDPS) and diethanolamine and added into the CB-filled NR/CR blends as a rubber additive. The ALK loadings were 0.0, 1.0, 3.0, 5.0 and 7.0 phr. It was found that the ALK exhibited shorter scorch and cure times and higher elongation at break of the CB-filled NR/CR blends. The ALK also exhibited higher torque differences, tensile modulus and tensile strength up to 5.0 phr of ALK and then decreased with further increases in the ALK loading. The swelling test proved that the 5.0 phr loading of ALK caused the highest degree in crosslink density of the CB-filled NR/CR blends.

Tensile Properties of Recycled Polypropylene (rPP)/Chloroprene Rubber (CR) Blends: Effect of CR Content

2015 ◽  
Vol 754-755 ◽  
pp. 192-196
Author(s):  
Salmah Husseinsyah ◽  
Chan Ming Yeng ◽  
Part Wei Ken
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Modulus Of Elasticity ◽  
Polymer Blending ◽  
Elongation At Break ◽  
Morphology Study ◽  
Cr Content ◽  
Recycled Polypropylene ◽  
Chloroprene Rubber

Polymer blending is one of the methods used to improve some insufficient properties of conventional polymers. The objective of this work was to study the effectiveness of CR content on the tensile properties and morphology study of recycled polypropylene (rPP)/ chloroprene rubber (CR) blends. The results indicated that the tensile strength and modulus of elasticity of rPP/CR blends decreased, however elongation at break increased as increasing CR content. The morphology study of rPP/CR blends showed the incompatibility between rPP and CR with the detachment of CR particles and CR particles pulled out from rPP surface.

Sign in / Sign up

Export Citation Format

Share Document