3D optimization of baffle arrangement in a multi-phase nanofluid natural convection based on numerical simulation

2019 ◽  
Vol 30 (5) ◽  
pp. 2583-2605 ◽  
Author(s):  
Mohammad Mohsen Peiravi ◽  
Javad Alinejad ◽  
D.D. Ganji ◽  
Soroush Maddah
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Target Function ◽  
Optimal Arrangement ◽  
Content Type ◽  
Multi Phase

Purpose The purpose of this study is investigating the effect of using multi-phase nanofluids, Rayleigh number and baffle arrangement simultaneously on the heat transfer rate and Predict the optimal arrangement type of baffles in the differentiation of Rayleigh number in a 3D enclosure. Design/methodology/approach Simulations were performed on the base of the L25 Taguchi orthogonal array, and each test was conducted under different height and baffle arrangement. The multi-phase thermal lattice Boltzmann based on the D3Q19 method was used for modeling fluid flow and temperature fields. Findings Streamlines, isotherms, nanofluid volume fraction distribution and Nusselt number along the wall surface for 104 < Ra < 108 have been demonstrated. Signal-to-noise ratios have been analyzed to predict optimal conditions of maximize and minimize the heat transfer rate. The results show that by choosing the appropriate height and arrangement of the baffles, the average Nusselt number can be changed by more than 57 per cent. Originality/value The value of this paper is surveying three-dimensional and two-phase simulation for nanofluid. Also using the Taguchi method for Predicting the optimal arrangement type of baffles in a multi-part enclosure. Finally statistical analysis of the results by using of two maximum and minimum target Function heat transfer rates.

Numerical simulation of water/alumina nanofluid mixed convection in square lid-driven cavity

2019 ◽  
Vol 30 (5) ◽  
pp. 2781-2807
Author(s):  
Davood Toghraie ◽  
Ehsan Shirani
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Richardson Number ◽  
Hartmann Number ◽  
Two Phase ◽  
Content Type ◽  
Driven Cavity

Purpose The purpose of this paper is to investigate the mixed convection of a two-phase water–aluminum oxide nanofluid in a cavity under a uniform magnetic field. Design/methodology/approach The upper wall of the cavity is cold and the lower wall is warm. The effects of different values of Richardson number, Hartmann number, cavitation length and solid nanoparticles concentration on the flow and temperature field and heat transfer rate were evaluated. In this paper, the heat flux was assumed to be constant of 10 (W/m2) and the Reynolds number was assumed to be constant of 300 and the Hartmann number and the volume fraction of solid nanoparticles varied from 0 to 60 and 0 to 0.06, respectively. The Richardson number was considered to be 0.1, 1 and 5. Aspect ratios were 1, 1.5 and 2. Findings Comparison of the results of this paper with the results of the numerical and experimental studies of other researchers showed a good correlation. The results were presented in the form of velocity and temperature profiles, stream and isotherm lines and Nusselt numbers. The results showed that by increasing the Hartmann number, the heat transfer rate decreases. An increase from 0 to 20 in Hartmann number results in a 20 per cent decrease in Nusselt numbers, and by increasing the Hartmann number from 20 to 40, a 16 per cent decrease is observed in Nusselt number. Accordingly, it is inferred that by increasing the Hartmann number, the reduction in the Nusselt number is decreased. As the Richardson number increased, the heat transfer rate and, consequently, the Nusselt number increased. Therefore, an increase in the Richardson number results in an increase of the Nusselt number, that is, an increase in Richardson number from 0.1 to 1 and from 1 to 5 results in 37 and 47 per cent increase in Nusselt number, respectively. Originality/value Even though there have been numerous investigations conducted on convection in cavities under various configurations and boundary conditions, relatively few studies are conducted for the case of nanofluid mixed convection in square lid-driven cavity under the effect of magnetic field using two-phase model.

The impacts of non-uniform magnetic field on free convection heat transfer of a magnetizable micropolar nanofluid

2019 ◽  
Vol 29 (10) ◽  
pp. 3685-3706
Author(s):  
Zafar Namazian ◽  
S.A.M. Mehryan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Content Type ◽  
Viscosity Parameter ◽  
Micropolar Nanofluid ◽  
Free Convection Heat

Purpose The purpose of this study is to numerically study the heat transfer of free convection of a magnetizable micropolar nanofluid inside a semicircular enclosure. Design/methodology/approach The flow domain is under simultaneous influences of two non-uniform magnetic fields generated by current carrying wires. The directions of the currents are the same. Although the geometry is symmetric, it is physically asymmetric. The impacts of key parameters, including Rayleigh number Ra = 103-106, Hartman number Ha = 0-50, vortex viscosity parameter Δ = 0-4, nanoparticles volume fraction φ = 0-0.04 and magnetic number Mnf = 0-1000, on the macro- and micro-scales flows, temperature and heat transfer rate are studied. Finding The outcomes show that dispersing of the nanoparticles in the host fluid increases the strength of macro- and micro-scale flows. When Mnf = 0, the increment of the vortex viscosity parameter increases the strength of the particles micro-rotations, while this characteristic is decreased by growing Δ for Mnf ≠ 0. The increment of Δ and Ha decreases the rate of heat transfer. The increment of Ha decreases the enhancement percentage of heat transfer rate because of dispersing nanoparticles, known as En parameter. In addition, the value of Δ has no effect on En. Moreover, the average Nusselt number Nuavg and En remain constant by increasing the magnetic number Mnf for different volume fraction values. Originality/value The authors believe that all of the results, both numerical and asymptotic, are original and have not been published elsewhere yet.

scholarly journals Mixed convective hybrid nanofluid flow in lid-driven undulated cavity: effect of MHD and Joule heating

2019 ◽  
Vol 16 (2) ◽  
pp. 109-126 ◽  
Author(s):  
Ishrat Zahan ◽  
R Nasrin ◽  
M A Alim
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Joule Heating ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Hybrid Nanoparticles ◽  
Wave Number ◽  
Hybrid Nanofluid

A numerical analysis has been conducted to show the effects of magnetohydrodynamic (MHD) and Joule heating on heat transfer phenomenon in a lid driven triangular cavity. The heat transfer fluid (HTF) has been considered as water based hybrid nanofluid composed of equal quantities of Cu and TiO2 nanoparticles. The bottom wall of the cavity is undulated in sinusoidal pattern and cooled isothermally. The left vertical wall of the cavity is heated while the inclined side is insulated. The two dimensional governing partial differential equations of heat transfer and fluid flow with appropriate boundary conditions have been solved by using Galerkin's finite element method built in COMSOL Multyphysics. The effects of Hartmann number, Joule heating, number of undulation and Richardson number on the flow structure and heat transfer characteristics have been studied in details. The values of Prandtl number and solid volume fraction of hybrid nanoparticles have been considered as fixed. Also, the code validation has been shown. The numerical results have been presented in terms of streamlines, isotherms and average Nusselt number of the hybrid nanofluid for different values of governing parameters. The comparison of heat transfer rate by using hybrid nanofluid, Cu-water nanofluid,  TiO2 -water nanofluid and clear water has been also shown. Increasing wave number from 0 to 3 enhances the heat transfer rate by 16.89%. The enhanced rate of mean Nusselt number for hybrid nanofluid is found as 4.11% compared to base fluid.

MHD hybrid nanofluid flow with convective heat transfer over a permeable stretching/shrinking surface with radiation

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Nur Syahirah Wahid ◽  
Norihan Md Arifin ◽  
Najiyah Safwa Khashi'ie ◽  
Ioan Pop ◽  
Norfifah Bachok ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Hybrid Nanofluid ◽  
Convective Boundary Conditions ◽  
Nanofluid Flow ◽  
Convective Boundary ◽  
Content Type ◽  
Shrinking Surface

Purpose The purpose of this paper is to numerically investigate the hybrid nanofluid flow with the imposition of magnetohydrodynamic (MHD) and radiation effects alongside the convective boundary conditions over a permeable stretching/shrinking surface. Design/methodology/approach The mathematical model is formulated in the form of partial differential equations (PDEs) and are then transformed into the form of ordinary differential equations (ODEs) by using the similarity variables. The deriving ODEs are solved numerically by using the bvp4c solver in MATLAB software. Stability analysis also has been performed to determine the stable solution among the dual solutions obtain. For method validation purposes, a comparison of numerical results has been made with the previous studies. Findings The flow and the heat transfer of the fluid at the boundary layer are described through the plot of the velocity profile, temperature profile, skin friction coefficient and local Nusselt number that are presented graphically. Dual solutions are obtained, but only the first solution is stable. For the realizable solution at the shrinking surface, the proliferation of nanoparticle volume fraction (copper) and magnetic (magnetohydrodynamics) parameters can impede the boundary layer separation. Also, Biot number could enhance the temperature profile and the heat transfer rate at the shrinking surface region. The incrementation of 0.1% of Biot number has enhanced the heat transfer rate by approximately 0.1% and the incrementation of 0.5% volume fraction for copper has reduced the heat transfer rate by approximately 0.17%. Originality/value The presented model and numerical results are original and new. It can be used as a future reference for further investigation and related practical application. The main contribution of this investigation includes giving the initial prediction and providing the numerical data for the other researchers for their future reference regarding the impacts of nanoparticles volumetric concentration towards the main physical quantities of interest in the presence of magnetic and radiation parameters with the convective boundary conditions.

Numerical investigations of heat transfer around a hot block subject to a cross-flow and an extended jet hole using ternary hybrid nanofluids

2021 ◽  
pp. 095440622110498
Author(s):  
Bouziane Boudraa ◽  
Rachid Bessaïh
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Laminar Flow ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Impinging Jet ◽  
Hybrid Nanofluid ◽  
Maximum Heat

In the last few years, modern heat transfer technologies significantly improved to provide more efficient systems in industries. One of those technologies is cooling electronic components in laminar flow using water nanofluids, which is interesting. This research used a ternary hybrid nanofluid with various nanoparticle forms to conduct a numerical investigation of three-dimensional heat transfer and fluid flow over a heated block exposed to a horizontal flow and an impinging jet. The effects of several variables such as the Reynolds number ratio [Formula: see text], volume fraction of nanoparticles [Formula: see text], length of extended jet hole [Formula: see text], and the influence of the inclination angle of the impinging jet inlet [Formula: see text] on the fluid flow and heat transfer were examined. Using the Ansys-Fluent 14.5 program and under laminar flow conditions, the finite-volume method was applied with the help of the SIMPLE algorithm to solve continuity, momentum, and energy equations. Several characteristics are assessed, including velocity streamline, isotherm contours, Nusselt number contours, the average Nusselt number ([Formula: see text]), the friction factor [Formula: see text], and drop pressure [Formula: see text]. The findings of the current analysis revealed that adding an impinging jet can boost the heat transfer rate up to [Formula: see text] better than a non-impingement jet. Also, a significant enhancement in the heat transfer rate was obtained when growing one of these parameters α, [Formula: see text], and E. Moreover, the ternary hybrid nanofluid with different nanoparticle forms significantly boosts the heat transfer rate compared to the traditional nanofluid. The maximum heat transfer is reached as the velocity of the impinging jet rises. Inclining the angle of the impinging jet inlet with [Formula: see text] toward the channel inlet boosted the rate of heat transfer up to [Formula: see text] compared to the perpendicular impinging jet [Formula: see text]. A strong consensus has been reached with the theoretical and experimental findings found in the literature.

Effect of replacing nanofluid instead of water on heat transfer in a channel with extended surfaces under a magnetic field

2019 ◽  
Vol 29 (4) ◽  
pp. 1249-1271 ◽  
Author(s):  
Saeed Aghakhani ◽  
Behzad Ghasemi ◽  
Ahmad Hajatzadeh Pordanjani ◽  
Somchai Wongwises ◽  
Masoud Afrand
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Lower Wall ◽  
Parallel Plates ◽  
Content Type ◽  
Extended Surfaces

PurposeThe purpose of this study is to conduct a numerical analysis of flow and heat transfer of water–aluminum oxide nanofluid in a channel with extended surfaces in the presence of a constant magnetic field. The channel consists of two parallel plates and five obstacles of constant temperature on the lower wall of the channel. The upper wall and the inlet and outlet lengths of the lower wall are insulated. A uniform magnetic field of the magnitude B0 is located beneath the obstacles. The nanofluid enters the channel with a uniform velocity and temperature, and a fully developed flow leaves the channel.Design/methodology/approachThe control volume-based finite difference and the SIMPLE algorithm were used for numerical solution. In addition to examining the effect of the Reynolds number, the effects of Hartman number, the volume fraction of nanoparticles, the height of obstacles, the length of obstacles and the distance between the obstacles were investigated.FindingsAccording to the results, the heat transfer rate increases with an increasing Reynolds number. As the Hartmann number increases, the heat transfer rate increases. The heat transfer rate also increases with an increase in the volume fraction of nanoparticles. The mean Nusselt number is reduced by an increasing height of obstacles. An increase in the distance between the obstacles in the presence of a magnetic field does not have a significant impact on the heat transfer rate. However, the heat transfer rate increases in the absence of a magnetic field, as the distance between the obstacles increases.Originality/valueThis paper is original and unpublished and is not being considered for publication elsewhere.

Numerical analysis of mixed convection of different nanofluids in concentric annulus

2019 ◽  
Vol 29 (4) ◽  
pp. 1506-1525 ◽  
Author(s):  
Ahad Abedini ◽  
Saeed Emadoddin ◽  
Taher Armaghani
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Flow Pattern ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Simple Algorithm ◽  
Content Type ◽  
Volume Method

Purpose This study aims to investigate the numerical analysis of mixed convection within the horizontal annulus in the presence of water-based fluid with nanoparticles of aluminum oxide, copper, silver and titanium oxide. Numerical solution is performed using a finite-volume method based on the SIMPLE algorithm, and the discretization of the equations is generally of the second order. Inner and outer cylinders have a constant temperature, and the inner cylinder temperature is higher than the outer one. The two cylinders can be rotated in both directions at a constant angular velocity. The effect of parameters such as Rayleigh, Richardson, Reynolds and the volume fraction of nanoparticles on heat transfer and flow pattern are investigated. The results show that the heat transfer rate increases with the increase of the Rayleigh number, as well as by increasing the volume fraction of the nanoparticles, the heat transfer rate increases, and this increase is about 8.25 per cent for 5 per cent volumetric fraction. Rotation of the cylinders reduces the overall heat transfer. Different directions of rotation have a great influence on the flow pattern and isotherms, and ultimately on heat transfer. The addition of nanoparticles does not have much effect on the flow pattern and isotherms, but it is quantitatively effective. The extracted results are in good agreement with previous works. Design/methodology/approach Studying mixed convection heat transfer in the horizontal annulus in the presence of a water-based fluid with aluminum oxide, copper, silver and titanium oxide nanoparticles is carried out quantitatively using a finite-volume method based on the SIMPLE algorithm. Findings Increasing the Rayleigh number increases the Nusselt number. Increasing the Richardson number increases heat transfer. Adding nanoparticles does not have much effect on the flow pattern but is effective quantitatively on heat transfer parameters. The addition of nanoparticles sometimes increases the heat transfer rate by about 8.25 per cent. In constant Rayleigh numbers, increasing the Reynolds number reduces heat transfer. The Rayleigh and Reynolds numbers greatly affect the isotherms and streamlines. In addition to the thermal conductivity of nanoparticles, the thermo-physical properties of nanoparticles has great effect in the formation of isotherms and streamlines and ultimately heat transfer. Originality/value Studying the effect of different direction of rotation on the isotherms and streamlines, as well as the comparison of different nanoparticles on mixed convection heat transfer in annulus.

A Numerical Study of the Simultaneous Natural Convective Heat Transfer From the Upper and Lower Surfaces of a Thin Isothermal Horizontal Circular Plate

2016 ◽  
Author(s):  
Patrick H. Oosthuizen ◽  
Abdulrahim Kalendar
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Prandtl Number ◽  
Convective Heat Transfer ◽  
Heat Transfer Rate ◽  
Convective Heat ◽  
Transfer Rate ◽  
The Mean ◽  
Adiabatic Section

Natural convective heat transfer from the top and bottom surfaces of a thin circular isothermal horizontal plate which, in general, has a centrally placed adiabatic section has been numerically investigated. The temperature of the plate surfaces is higher than the temperature of the surrounding fluid. The range of conditions considered is such that laminar, transitional, and turbulent flow occurs over the plate. The heat transfer from the upper and lower surfaces of the plate as well as the mean heat transfer rate from the entire surface of the plate have been considered. The flow has been assumed to be axisymmetric and steady. The k-epsilon turbulence model with account being taken of buoyancy force effects has been used and the solution has been obtained using the commercial CFD solver ANSYS FLUENT©. The heat transfer rate from the heated plate has been expressed in terms of a Nusselt number based on the outside plate diameter and the difference between the plate temperature and the fluid temperature far from the plate. The mean Nusselt number is dependent on the Rayleigh number, the ratio of the diameter of the inner adiabatic section to the outer plate diameter, and the Prandtl number. Results have only been obtained for a Prandtl number of 0.74, i.e., effectively the value for air. The variations of the mean Nusselt number averaged over both the upper and lower surfaces and of the mean Nusselt numbers for the upper surface and for the lower surface with Rayleigh number for various adiabatic section diameter ratios have been studied. The use of a reference length scale to allow the correlation of these mean Nusselt number-Rayleigh number variations has been investigated.

scholarly journals Free Convection of Ag/H2O Nanofluid in Square Cavity with Different Position and Orientation of Egg Shaped Cylinder

2021 ◽  
Vol 53 (4) ◽  
pp. 210409
Author(s):  
Atheer Saad Hashim
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Free Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Orientation Angle ◽  
Numerical Results ◽  
Vertical Position ◽  
Square Cavity

A numerical simulation was conducted to study the free convection of Ag/H2O nanofluid between a square cavity with cold walls and an egg shaped cylinder with a hot wall. Utilizing the egg equation, dimensionless governing equations were solved using the Galerkin Finite Element Method (GFEM). In this work, several parameters were studied, i.e. Rayleigh number (103 ≤ Ra ≤ 106), volume fraction (0 ≤ φ ≤ 0.05), position (-0.2 ≤ Y ≤ 0.2), and orientation angle (-90° ≤ γ ≤ 90°). The numerical results are presented as streamline contours, isotherm contours, and local and average Nusselt numbers. Moreover, the results were used to analyze the fluids’ structure, temperature distribution, and heat transfer rate. The numerical results confirmed that the stream intensity value increased with an increase of the Rayleigh number as well as the movement of the cylinder towards the bottom wall for all values of the orientation angle. Variation of the vertical position of the cylinder inside the cavity had a noticeable effect on , which increased by 50% at γ = -90°, and by 58% at γ = -45°. However, at Y = -0.2,  increased by 58% at γ = -45° and decreased by 7% at γ = -90°. The highest heat transfer rate was obtained at high Rayleigh number (Ra = 106), volume fraction (φ = 0.05), negative position (Y = -0.2), and the highest positive orientation angle (γ = 90°).

scholarly journals Numerical study of natural turbulent convection of nanofluids in a tall cavity heated from below

2016 ◽  
Vol 20 (6) ◽  
pp. 2051-2064 ◽  
Author(s):  
Ridha Mebrouk ◽  
Mahfoud Kadja ◽  
Mohamed Lachi ◽  
Stéphane Fohanno
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Heat Source ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Numerical Study ◽  
Solid Volume Fraction ◽  
Turbulent Convection ◽  
Average Heat

In the present paper a numerical study of natural turbulent convection in a tall cavity filled with nanofluids. The cavity has a heat source embedded on its bottom wall, while the left, right and top walls of the cavity are maintained at a relatively low temperature. The working fluid is a water based nanofluid having three nanoparticle types: alumina, copper and copper oxid. The influence of pertinent parameters such as Rayleigh number, the type of nanofluid and solid volume fraction of nanoparticles on the cooling performance is studied. Steady forms of twodimensional Reynolds-Averaged-Navier-Stokes equations and conservation equations of mass and energy, coupled with the Boussinesq approximation, are solved by the control volume based discretisation method employing the SIMPLE algorithm for pressure-velocity coupling. Turbulence is modeled using the standard k-? model. The Rayleigh number, Ra, is varied from 2.491009 to 2.491011. The volume fractions of nanoparticles were varied in the interval 0??? 6% . Stream lines, isotherms, velocity profiles and Temperature profiles are presented for various combinations of Ra, the type of nanofluid and solid volume fraction of nanoparticles. The results are reported in the form of average Nusselt number on the heated wall. It is shown that for all values of Ra, the average heat transfer rate from the heat source increases almost linearly and monotonically as the solid volume fraction increases. Finally the average heat transfer rate takes on values that decrease according to the ordering Cu, CuO and Al2O3.

Sign in / Sign up

Export Citation Format

Share Document