The effect of colemanite on the friction performance of automotive brake friction materials

2016 ◽  
Vol 68 (1) ◽  
pp. 92-98 ◽  
Author(s):  
ilker Sugozu ◽  
ibrahim mutlu ◽  
Kezban Banu Sugozu
Keyword(s):  
Friction Coefficient ◽  
Friction And Wear ◽  
Negative Effects ◽  
Wear Performance ◽  
Industrial Firms ◽  
Friction Materials ◽  
Content Type ◽  
Friction Performance ◽  
Brake Lining ◽  
Automotive Brake

Purpose – The purpose of this paper is to investigate use of colemanite (C) upon friction and wear performance of automotive brake lining. Brake lining production with the boron product colemanite addition and braking characterization investigated for development of non-asbestos organic (NAO) brake lining because of negative effects on human health and environmental hazard of asbestos containing linings. During the braking, brake lining is warmed up extremely due to friction, and the high temperature causes to decreasing of breaking performance. Colemanite has high melting temperature, and this makes this material valuable for brake lining. Design/methodology/approach – This study investigated the effect of colemanite (C) upon friction and wear performance of automotive brake lining. Based on a simple experimental formulation, different amounts of boron product colemanite were used and then evaluated using a friction assessment and screening test. In these specimens, half of the samples (shown with H indices) were heat treated in 4 h at 180°C temperature. Friction coefficient, wear rate and scanning electron microscope for friction surfaces were used to assess the performance of these samples. Findings – The results of test showed that colemanite can substantially improve properties of friction materials. The friction coefficient of friction materials modified with colemanite varies steadily with the change of temperature, and the wearing rate of friction materials is relatively low by using colemanite. Heat treatment-applied samples (CH) have provided a higher and stable friction coefficient. These results indicate that colemanite has ideal application effect in various friction materials. Originality/value – This paper fulfils an identified information and offers practical help to the industrial firms working with brake lining and also to the academicians working on wear of materials. Parallel results have been presented between previously reported and present study, in view of brake characteristics and wear resistance. Use of the lower cost and productive organic sources of material are the main improvement of the present study.

Friction and wear properties of friction materials containing nano/micro-sized SiO2 particles

2016 ◽  
Vol 68 (2) ◽  
pp. 259-266 ◽  
Author(s):  
Kezban Banu Sugozu ◽  
Behcet Daghan ◽  
Ahmet Akdemir ◽  
Necati Ataberk
Keyword(s):  
Friction Coefficient ◽  
Friction And Wear ◽  
Poor Performance ◽  
Wear Properties ◽  
Wear Performance ◽  
Content Type ◽  
Conventional Procedure ◽  
Friction And Wear Properties ◽  
Sio2 Particles ◽  
Brake Lining

Purpose – Among the components used for a car brake lining, the chemical and structural properties of the abrasives, jointly with the morphology and size of the particles influence the friction parameters and stability of the composite. This paper aims to investigate the effect of nano SiO2 particles in brake pads on friction and wear properties. Design/methodology/approach – In this paper, the effects of SiO2 (Silica) particles of varying size on the friction-wear properties of polymeric friction composites are investigated. Four friction composites were prepared containing (5, 10 Wt.%) micro silica (MS) particles and (5, 10 Wt.%) nano silica (NS) particles. The samples were produced by a conventional procedure for a dry formulation following dry-mixing, pre-forming and hot pressing. Friction and wear characteristics of the specimens against to a disk made of cast iron were studied. Friction coefficient, specific wear rate and hardness of specimens were obtained. Detailed examinations on the worn surface were analyzed using a scanning electron microscope. Findings – The results of test showed that the inclusion of nano silicon carbide (SiC) powder improved the wear performance significantly. Friction coefficient (μ) of NS samples was higher than the MS samples. Micro-SiC showed poor performance and μ. High wear performance was exhibited in materials containing 5 Wt.% NS and 10 Wt.% NS. Originality/value – This paper emphasizes the importance of nano-composites in the automotive industry and helps to industrial firms and academicians working on wear of materials.

The Role of Copper on the Friction and Wear Performance of Automotive Brake Friction Materials

2011 ◽  
Vol 5 (1) ◽  
pp. 9-18 ◽  
Author(s):  
Seong Jin Kim ◽  
Jae Young Lee ◽  
Jai Min Han ◽  
Yoon Cheol Kim ◽  
Hyun Dal Park ◽  
...  
Keyword(s):  
Friction And Wear ◽  
Wear Performance ◽  
Friction Materials ◽  
Automotive Brake

Friction and wear properties of an automobile brake lining reinforced by lignin fiber and glass fiber

2017 ◽  
Vol 69 (5) ◽  
pp. 775-781 ◽  
Author(s):  
Wang Chengmin ◽  
Yang Xuefeng ◽  
Cai Xiguang ◽  
Ma Tao ◽  
Li Yunxi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Friction And Wear ◽  
Wear Properties ◽  
Fatigue Wear ◽  
Friction Materials ◽  
Content Type ◽  
Friction Testing ◽  
Friction And Wear Properties ◽  
Brake Lining

Purpose This paper aims to thrash out friction and wear properties of automobile brake lining reinforced by lignin fiber and glass fiber in braking process. Design/methodology/approach ABAQUS finite element software was used to analyze thermo-mechanical coupled field of friction materials. XD-MSM constant speed friction testing machine was used to test friction and wear properties of friction material. Worn surface morphology and mechanism of friction materials were observed by using scanning electron microscope. Findings The results show that when the temperature was below 350°C, worn mechanism of MFBL was mainly fatigue wear and abrasive wear, and worn mechanism of GFBL was mainly fatigue wear because MFBL contained lignin fiber. Therefore, it exhibits better mechanical properties and friction and wear properties than those of GFBL. Originality/value Lignin fiber can improve mechanical properties and friction and wear properties of the automobile brake lining.

Hybrid Biological Fiber-Reinforced Resin-Based Friction Materials Friction and Wear Performance Test

2013 ◽  
Vol 461 ◽  
pp. 388-396 ◽  
Author(s):  
Yun Hai Ma ◽  
Sheng Sheng Ma ◽  
Sheng Long Shen ◽  
Jin Tong ◽  
Li Guo
Keyword(s):  
Friction Coefficient ◽  
Experimental Design ◽  
Mass Fraction ◽  
Friction And Wear ◽  
Friction Material ◽  
Orthogonal Experimental Design ◽  
Fiber Reinforced ◽  
Wear Performance ◽  
Friction Materials ◽  
Reinforced Fiber

Friction material is essential for automotive braking system. Based on previous study of existing friction material problems, hybrid biological fiber-reinforced resin-based friction materials (HBRMs, from the reinforced fiber component of resin-based friction materials) were explored in this study. Bamboo fiber, jute fiber and wool fiber (all have length of 3-5 mm) were processed to make three types of HBRMs and considered as three factors of biological reinforced fiber in test using orthogonal experimental design. Each factor had three levels of 1%, 2% and 3% fiber mass fraction while the ratio of other raw materials remains unchanged. According to the orthogonal experimental design table, nine formulations (denoted as M1-M9) were determined to test the HBRMs. For comparison, non-bio-fiber reinforced friction material (NBM) was added in the test. The properties of the HBRMs tested included Rockwell hardness, impact strength and density. The friction and wear performance of the braking materials was examined by a speed friction tester. The results show that the friction coefficient of the HBRMs was slightly higher than that of the NBM, indicating biological fibers affected the friction coefficient. The friction coefficient of the HBRMs decreased firstly with the increase of temperature and had the lowest value when the temperature reached 300°C, and it increased then as temperature increased. During recovery process, the friction coefficient of the HBRMs firstly increased with the decrease of temperature and then decreased greatly when the temperature dropped to 100°C. The wear rates of the HBRMs increased with the increase of temperature and reached maximum value when temperature reached 200°C, then it decreased with the increase of temperature. The results of fuzzy comprehensive evaluation analysis on the friction coefficient and wear rate show that the best comprehensive properties were presented when the mass fraction of bamboo, jute and wool fiber were 3%, 3% and 1%，respectively.

Effect of the size on the friction characteristics of brake friction materials: a case study with Al2O3

2018 ◽  
Vol 70 (6) ◽  
pp. 1020-1024 ◽  
Author(s):  
Banu Sugözü ◽  
Behcet Dağhan ◽  
Ahmet Akdemir
Keyword(s):  
Automotive Industry ◽  
Gray Cast Iron ◽  
Industrial Firms ◽  
Friction Materials ◽  
Content Type ◽  
Nano Alumina ◽  
Brake Dynamometer ◽  
Worn Surface ◽  
Automotive Brake

Purpose The purpose of this paper is to study the potential of alumina (Al2O3) in nanometer size in automotive brake friction materials. Design/methodology/approach Four brake linings containing alumina differing in particle size (355 µm and 80 nm) and various amount (5 and 10 Wt.%) were designed and produced. The hardness, density and porosity of the samples were measured. All samples were tested on a full-scale brake dynamometer with gray cast iron disc to determine the tribological properties. Detailed examinations on the worn surface were analyzed using a scanning electron microscopy. Findings It was concluded that all performance parameters were beneficially affected because of nano alumina. Originality/value This paper emphasizes the importance of nano-composites in the automotive industry and helps industrial firms and academicians working on wear of materials.

A comparative study of the friction and wear performance of Fe-based bulk metallic glass under different conditions

2017 ◽  
Vol 69 (6) ◽  
pp. 919-924
Author(s):  
Dawit Zenebe Segu ◽  
Pyung Hwang
Keyword(s):  
Metallic Glass ◽  
Abrasive Wear ◽  
Bulk Metallic Glass ◽  
Friction And Wear ◽  
Deionized Water ◽  
Wear Scar ◽  
Dry Sliding ◽  
Wear Performance ◽  
Content Type ◽  
Conventional Material

Purpose This study aims to compare the friction and wear behaviors of Fe68.3C6.9Si2.5 B6.7P8.8Cr2.2Al2.1Mo2.5 bulk metallic glass (BMG) under sliding using dry, deionized water-lubricated and oil-lubricated conditions. The comparison was performed using a unidirectional ball-on-flat tribometer under different applied loads, and the results were compared to the properties of a conventional material, SUJ2. Fe-based BMG materials have recently been attracting a great deal of attention for prospective engineering applications. Design/methodology/approach As a part of the development of Fe-based BMGs that can be cost-effectively produced in large quantities, an Fe-based BMG Fe68.8C7.0Si3.5B5.0P9.6 Cr2.1Mo2.0Al2.0 with high glass forming ability was fabricated. In the present study, the friction and wear properties of Fe-based BMG has been comparatively evaluated under dry sliding, deionized water- and oil-lubricated conditions using a unidirectional ball-on-flat tribometer under different applied loads, and the results were compared to the properties of conventional material SUJ2. Findings The results show that the Fe-based BMG had better friction performance than the conventional material. Both the friction coefficient and wear mass loss increased with increasing load. The sliding wear mechanism of the BMG changed with the sliding conditions. Under dry sliding conditions, the wear scar of the Fe-based BMG was characterized by abrasive wear, plastic deformation, micro-cracks and peeling-off wear. Under water- and oil-lubricated conditions, the wear scar was mainly characterized by abrasive wear and micro-cutting. Originality/value In this investigation, the authors developed a new BMG alloy Fe68.8C7.0Si3.5B5.0P9.6Cr2.1Mo2.0Al2.0 to improve the friction and wear performance under dry sliding, deionized water- and oil- lubricated conditions.

Tribological behavior of UHMWPE in water lubrication: the effect of molding temperature

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Xincong Zhou ◽  
Chaozhen Yang ◽  
Jian Huang ◽  
Xueshen Liu ◽  
Da Zhong ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Friction Coefficient ◽  
Friction And Wear ◽  
Wear Loss ◽  
Content Type ◽  
Molding Temperature ◽  
Melting Temperatures ◽  
Ultra High Molecular Weight ◽  
Wear Tests ◽  
Friction And Wear Tests

Purpose Ultra-high molecular weight polyethylene (UHMWPE) is adopted in water-lubricated bearings for its excellent performance. This paper aims to investigate the tribological properties of UHMWPE with a molecular weight of 10.2 million (g mol‐1) under different molding temperatures. Design/methodology/approach The UHMWPE samples were prepared by mold pressing under constant pressure and different molding temperatures (140°C, 160°C, 180°C, 200°C, 220°C). The friction and wear tests in water were conducted at the RTEC tribo-tester. Findings The friction coefficient and wear loss decreased first and rose later with the increasing molding temperature. The minimums of the friction coefficient and wear loss were found at the molding temperatures of 200°C. At low melting temperatures, the UHMWPE molecular chains could not unwrap thoroughly, leading to greater abrasive wear. On the other hand, high melting temperatures will cause the UHMWPE molecular chains to break up and decompose. The optimal molding temperatures for UHMWPE were found to be 200°C. Originality/value Findings are of great significance for the design of water-lubricated UHMWPE bearings.

Study on the Friction and Wear Behavior of Grind-Hardened Layer

2010 ◽  
Vol 431-432 ◽  
pp. 385-388 ◽  
Author(s):  
Jian Hua Zhang ◽  
Pei Qi Ge ◽  
Lei Zhang ◽  
Yang Yu ◽  
Hui Li
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Wear Debris ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Hardened Layer ◽  
Hardened Steel ◽  
Wear Performance ◽  
Friction And Wear Behavior ◽  
Grind Hardening

The grind-hardening technology utilizes the grinding heat to harden the surface of the workpiece. The friction and wear performance of the grind-hardened layer is one of the important parameters. In this paper, the friction and wear performance of the grind-hardened layer was studied by the friction and wear experiment. The wear rate and the friction coefficient of the grind-hardened steel were studied by comparing with conventional hardened steel and non-hardened steel. The surface worn morphology and the collected wear debris of the grind-hardened steel were observed during the experiment. The wear mechanism of the grind-hardened steel was analyzed under different friction conditions.

Sign in / Sign up

Export Citation Format

Share Document