The influence of emitter resistance on the electrical parameters of mono- and multicrystalline silicon solar cells

2019 ◽  
Vol 36 (3) ◽  
pp. 90-94
Author(s):  
Barbara Swatowska ◽  
Piotr Panek ◽  
Dagmara Michoń ◽  
Aleksandra Drygała
Keyword(s):  
Solar Cells ◽  
Contact Resistance ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Multicrystalline Silicon ◽  
Silicon Solar Cells ◽  
Electrical Parameters ◽  
Content Type ◽  
Diffusion Parameters

Purpose The purpose of this study was the comparison and analysis of the electrical parameters of two kinds of silicon solar cells (mono- and multicrystalline) of different emitter resistance. Design/methodology/approach By controlling of diffusion parameters, silicon mono- (Cz-Si) and multicrystalline (mc-Si) solar cells with different emitter resistance values were produced – 22 and 48 Ω/□. On the basis of current-voltage measurements of cells and contact resistance mapping, the properties of final solar cells based on two different materials were compared. Additionally, the influence of temperature on PV cells efficiency and open circuit voltage (Uoc) were investigated. The PC1D simulation was useful to determine spectral dependence of external quantum efficiency of solar cells with different emitter resistance. The silicon solar cells of 25 cm2 area and 240 µm thickness were investigated. Findings Considering the all stages of cell technology, the best structure is silicon solar cell with sheet resistance (Rsheet) of 45-48 Ω/□. Producing of an emitter with this resistance allowed to obtain cells with a fill factor between 0.725 and 0.758, Uoc between 585 and 612 mV, short circuit current (Isc) between 724 and 820 mA. Originality/value Measurements and analysis confirmed that mono- and multicrystalline silicon solar cells with 48 Ω/□ emitter resistance have better parameters than cells with Rsheet of 22 Ω/□. The contact resistance is the highest for mc-Si with Rsheet of 48 Ω/□ and reaches the value 3.8 Ωcm.

The Effect of Al-BSF on Seff and Rb in Industrialized Mono-Silicon Solar Cells

2012 ◽  
Vol 472-475 ◽  
pp. 1846-1850
Author(s):  
Shan Shan Dai ◽  
Gao Jie Zhang ◽  
Xiang Dong Luo ◽  
Jing Xiao Wang ◽  
Wen Jun Chen ◽  
...  
Keyword(s):  
Solar Cells ◽  
Spectral Response ◽  
Short Circuit ◽  
Rear Surface ◽  
Surface Recombination ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Silicon Solar Cells ◽  
Back Surface

In this work, the effect of aluminum back surface field formed by screen printed various amount of Al paste on the effective rear surface recombination velocity (Seff) and the internal rear reflectance coeffeicient (Rb) of commercial mono-silicon solar cells was investigated. We demonstrated the effect of Seffand Rbon the performance of Al-BSF solar cells by simulating them with PC1D. The simulated results showed that the lower Seffcould get higher open circuit voltage (Voc), at the same time, the larger Rbcould get higher short-circuit current (Isc). Experimentally, we investigated the Seffand Rbthrough depositing Al paste with various amount (3.7, 5, 6, and 8 mg/cm2) for fabricating Al-BSF mono-silicon solar cells. Four group cells were characterized by light I-V, spectral response, hemispherical reflectance and scanning electron microscope (SEM) measurements. It was found that, a minimum Seffof 350 cm/s was gotten from the cells with Al paste of 8 mg/cm2, which was extracted by matching quantum efficiency (QE) from 800 nm to 1200 nm with PC1D, and a maximum Rbof 53.5% was obtained from Al paste of 5 mg/cm2by calculating at 1105 nm with PC1D. When the amount of Al paste was higher than 5mg/cm2, there were less Seffand lower Rb. On the other hand, when Al amount was 3.7mg/cm2, it was too little to form a closed BSF. Based on the SEM graphs and simulations with PC1D, a simple explaination was proposed for the experimental results.

Study on the Performance of Aluminum Thick Film Contacts for Silicon Solar Cells

2013 ◽  
Vol 833 ◽  
pp. 241-246
Author(s):  
Ming Fu ◽  
Hong Yong Li ◽  
Gong Lei Jin ◽  
Lin Fan ◽  
Dong Chen ◽  
...  
Keyword(s):  
Solar Cells ◽  
Thick Film ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Silicon Solar Cells ◽  
Back Surface ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Photoelectric Properties

Aluminum rear contacts of silicon solar cells are made commonly by screen-printing aluminum paste and sintering process. Aluminum thick film contacts have a direct effect on photoelectric properties of solar cells, like open circuit voltage (Voc), short circuit current (Isc), conversion efficiency (η), etc. The principle of Al-back surface field (BSF) has been studied in this paper. With thermal gravimetric analysis and differential scanning calorimetry (TGA-DSC) method, the chemical reactions between aluminum thick film and silicon substrate during heat treatment have been investigated. The microstructure of aluminum thick film contacts were analysed by SEM. The electrical properties of Al-BSF are improved by adding a proper amount of nano silicon to the aluminum paste.

Influence of ITO layer application on electrical parameters of silicon solar cells with screen printed front electrode

2016 ◽  
Vol 33 (3) ◽  
pp. 172-175 ◽  
Author(s):  
Kazimierz Drabczyk ◽  
Jaroslaw Domaradzki ◽  
Grazyna Kulesza-Matlak ◽  
Marek Lipinski ◽  
Danuta Kaczmarek
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Performance ◽  
Silicon Solar Cells ◽  
Content Type ◽  
Crystalline Silicon Solar Cells ◽  
Screen Printed

Purpose The purpose of this paper was investigation and comparison of electrical and optical properties of crystalline silicon solar cells with ITO or TiO2 coating. The ITO, similar to TiO2, is very well transparent in the visible part of optical radiation; however, its low resistivity (lower that 10-3 Ohm/cm) makes it possible to use simultaneously as a transparent electrode for collection of photo-generated electrical charge carriers. This might also invoke increasing the distance between screen-printed metal fingers at the front of the solar cell that would increase of the cell’s active area. Performed optical investigation showed that applied ITO thin film fulfill standard requirements according to antireflection properties when it was deposited on the surface of silicon solar cell. Design/methodology/approach Two sets of samples were prepared for comparison. In the first one, the ITO thin film was deposited directly on the crystalline silicon substrate with highly doped emitter region. In the second case, the TCO film was deposited on the same type of silicon substrate but with additional ultrathin SiO2 passivation. The fingers lines of 80 μm width were then screen-printed on the ITO layer with two different spaces between fingers for each set. The influence of application of the ITO electrode and the type of metal electrodes patterns on the electrical performance of the prepared solar cells was investigated through optical and electrical measurements. Findings The electrical parameters such as short-circuit current (Jsc), open circuit voltage (Voc), fill factor (FF) and conversion efficiency were determined on a basis of I-V characteristics. Short-circuit current density (Jsc) was equal to 32 mA/cm2 for a solar cell with a typical antireflection layer and 31.5 mA/cm2 for the cell with ITO layer, respectively. Additionally, electroluminescence of prepared cells was measured and analysed. Originality/value The influence of the properties of ITO electrode on the electrical performance of crystalline silicon solar cells was investigated through complex optical, electrical and electroluminescence measurements.

N-Type Hydrogenated Microcrystalline Silicon Oxide Films and Their Applications in Micromorph Silicon Solar Cells

2011 ◽  
Vol 1321 ◽  
Author(s):  
Amornrat Limmanee ◽  
Songkiate Kittisontirak ◽  
Channarong Piromjit ◽  
Jaran Sritharathikhun ◽  
Kobsak Sriprapha
Keyword(s):  
Solar Cells ◽  
Silicon Oxide ◽  
Volume Fraction ◽  
Short Circuit ◽  
Oxide Films ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Silicon Solar Cells ◽  
Microcrystalline Silicon ◽  
Shunt Resistance

ABSTRACTWe have prepared n-type hydrogenated microcrystalline silicon oxide films (n μc-SiO:H) and investigated their structural, electrical and optical properties. Raman spectra shows that, amorphous phase of the n μc-SiO:H films tends to increase when the CO2/SiH4 ratio increases from 0 to 0.28 resulting in a reduction of the crystalline volume fraction (Xc) from 70 to 12%. Optical bandgap (E04) becomes gradually wider while dark conductivity and refractive index (n) continuously drop with increasing CO2/SiH4 ratio. The n μc-SiO:H films have been practically applied as a n layer in top cell of a-SiO:H/μc-Si:H micromorph silicon solar cells. We found that, open circuit voltage (Voc) and fill factor (FF) of the cells gradually increased, while short circuit current density (Jsc) remained almost the same value with increasing CO2/SiH4 ratio for n top layer deposition up to 0.23. The highest initial cell efficiency of 10.7% is achieved at the CO2/SiH4 ratio of 0.23. The enhancement of the Voc is supposed to be due to a reduction of reverse bias at sub cell connection (n top/p bottom interface). An increase of shunt resistance (Rsh) which is caused by a better tunnel recombination junction contributes to the improvement in the FF. Quantum efficiency (QE) results indicate no difference between the cells using n top μc-SiO:H and the cells with n top μc-Si:H layers. These results reveal that, the n μc-SiO:H films in this study do not work as an intermediate reflector to enhance light scattering inside the solar cells, but mainly play a key role to allow ohmic and low resistive electrical connection between the two adjacent cells in the micromorph silicon solar cells.

A Carrier Lifetime Model for the Optical Degradation of Amorphous Silicon Solar Cells

1985 ◽  
Vol 49 ◽  
Author(s):  
Z E. Smith ◽  
S. Wagner
Keyword(s):  
Solar Cells ◽  
Amorphous Silicon ◽  
Carrier Lifetime ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Silicon Solar Cells ◽  
Carrier Lifetimes ◽  
Bond Density ◽  
Degradation Data

AbstractThe light-induced performance degradation of amorphous silicon solar cells is described well by a model in which the carrier lifetimes are determined by the dangling bond density. The kinetics of the defect generation follow the model in which band-to-band recombination provides the energy for the creation of dangling bonds, which in turn introduce gap states that reduce carrier lifetime. Degradation will be slower in solar cells operating at lower excess carrier concentrations. This is documented with a comparison of degradation data for cells of different i-layer thickness, cells operating at open circuit vs. load, and for single vs. cascade cells. The model also correctly predicts the relation between short circuit current and fill factor degradation. At sufficiently long times, the efficiency will decrease at approximately the same rate for all cell structures and dimensions, with an offset in time between different device types which can be calculated.

scholarly journals Cheap Sensor Made of Multicrystalline Silicon for Insolation and Temperature Measurements

2016 ◽  
Vol 23 (4) ◽  
pp. 583-591 ◽  
Author(s):  
Tadeusz Rodziewicz ◽  
Janusz Teneta ◽  
Aleksander Zaremba ◽  
Maria Wacławek
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
The Other ◽  
Silicon Solar Cells ◽  
Temperature Calculation ◽  
Direct Indication ◽  
Indirect Indication

Abstract In the paper some results on measurement of insolation and „real” cell’s temperature carried out with use of standard silicon solar cells are presented. Two identical cells are applied in such a sensor. Short circuit current of one cell is a direct indication of insolation value and open circuit voltage of the other cell is indirect indication of actual sensor’s temperature but in this case more complex formula must be used for temperature calculation.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Low Temperature ◽  
Triple Junction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Metal Line ◽  
Solar Simulator ◽  
Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

Sign in / Sign up

Export Citation Format

Share Document