scholarly journals Support optimization for additive manufacturing: application to FDM

2018 ◽  
Vol 24 (1) ◽  
pp. 69-79 ◽  
Author(s):  
Nicolas Boyard ◽  
Olivier Christmann ◽  
Mickaël Rivette ◽  
Olivier Kerbrat ◽  
Simon Richir
Keyword(s):  
Case Studies ◽  
Fused Deposition Modeling ◽  
Honeycomb Structure ◽  
Content Type ◽  
Fused Deposition ◽  
Modeling Process ◽  
Full Structure ◽  
Deposition Modeling ◽  
Support Optimization ◽  
Withdrawal Of Support

Purpose This paper aims to present a new methodology to optimize the support generation within the fused deposition modeling process. Design/methodology/approach Different methods of support generation exist, but they are limited with regards to complex parts. This paper proposes a method dedicated to support generation, integrated into CAD software. The objective is to minimize the volume of support and its impact on a part’s surface finish. Two case studies illustrate the methodology. The support generation is based on an octree’s discretization of the part. Findings The method represents a first solid step in the support optimization for a reasonable calculation time. It has the advantage of being virtually automatic. The only tasks to be performed by the designer are to place the part to be studied with respect to the CAD reference and to give the ratio between the desired support volume and the maximum volume of support. Research limitations/implications In the case studies, a low gain in manufacturing time was observed. This is explained by the honeycomb structure of the support generated by a common slicing software, whereas the proposed method uses a “full” structure. It would be interesting to study the feasibility of an optimized support, with a honeycomb structure but with a preservation of the surface which is in contact with the part. Originality/value This solution best fits the needs of the designer and manufacturer already taking advantage of existing solutions. It is adaptable to any part if the withdrawal of support is taken into account. It also allows the designer to validate the generation of support throughout the CAD without breaking the digital chain.

Synthesis and properties of modified PBT for FDM

2017 ◽  
Vol 23 (4) ◽  
pp. 804-810 ◽  
Author(s):  
Shiqing Cao ◽  
Dandan Yu ◽  
Weilan Xue ◽  
Zuoxiang Zeng ◽  
Wanyu Zhu
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Fused Deposition Modeling ◽  
Complex Structure ◽  
Three Dimensional ◽  
Sebacic Acid ◽  
Wire Drawing ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling

Purpose The purpose of this paper is to prepare a new modified polybutylene terephalate (MPBT) for fused deposition modeling (FDM) to increase the variety of materials compatible with printing. And the printing materials can be used to print components with a complex structure and functional mechanical parts. Design/methodology/approach The MPBT, poly(butylene terephalate-co-isophthalate-co-sebacate) (PBTIS), was prepared for FDM by direct esterification and subsequent polycondensation using terephthalic acid (PTA), isophthalic acid (PIA), sebacic acid (SA) and 1,4-butanediol (BDO). The effects of the content of PIA (20-40 mol%) on the mechanical properties of PBTIS were investigated when the mole per cent of SA (αSA) is zero. The effects of αSA (0-7mol%) on the thermal, rheological and mechanical properties of PBTIS were investigated at nPTA/nPIA = 7/3. A desktop wire drawing and extruding machine was used to fabricate the filaments, whose printability and anisotropy were tested by three-dimensional (3D) printing experiments. Findings A candidate content of PIA introducing into PBT was obtained to be about 30 per cent, and the Izod notched impact strength of PBTIS increased with the increase of αSA. The results showed that the PBTIS (nPTA/nPIA = 7/3, αSA = 3-5mol%) is suitable for FDM. Originality/value New printing materials with good Izod notched impact strength were obtained by introducing PIA and SA (nPTA/nPIA = 7/3, αSA = 3-5 mol%) into PBT and their anisotropy are better than that of ABS.

Fracture assessment of polycarbonate parts produced by fused deposition modeling in the out-of-plane printing direction – effect of raster angle

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Iman Sedighi ◽  
Majid R. Ayatollahi ◽  
Bahador Bahrami ◽  
Marco A. Pérez-Martínez ◽  
Andrés A. Garcia-Granada
Keyword(s):  
Fracture Toughness ◽  
Finite Element ◽  
Fracture Behavior ◽  
Fused Deposition Modeling ◽  
Mode I ◽  
Content Type ◽  
Fused Deposition ◽  
Out Of Plane ◽  
Deposition Modeling ◽  
Fracture Tests

Purpose The purpose of this paper is to study the Mode I fracture behavior of polycarbonate (PC) parts produced using fused deposition modeling (FDM). The focus of this study is on samples printed along the out-of-plane direction with different raster angles. Design/methodology/approach Tensile and Mode I fracture tests were conducted. Semi-circular bend specimens were used for the fracture tests, which were printed in four different raster patterns of (0/90), (15/−75) (30/−60) and (45/−45). Moreover, the finite element method (FEM) was used to determine the applicability of linear elastic fracture mechanics (LEFM) for the printed PC parts. The fracture toughness results, as well as the fracture path and the fracture surfaces, were studied to describe the fracture behavior of the samples. Findings Finite element results confirm that the use of LEFM is allowed for the tested PC samples. The fracture toughness results show that changing the direction of the printed rasters can have an effect of up to 50% on the fracture toughness of the printed parts, with the (+45/−45) and (0/90) orientations having the highest and lowest resistance to crack propagation, respectively. Moreover, except for the (0/90) orientation, the other samples have higher crack resistance compared to the bulk material. The fracture toughness of the tested PC depends more on the toughness of the printed sample, rather than its tensile strength. Originality/value The toughness and the energy absorption capability of the printed samples (with different raster patterns) were identified as the main properties affecting the fracture toughness of the AM PC parts. Because the fracture resistance of almost all the samples was higher than that of the base material, it is evident that by choosing the right raster patterns for 3D-printed parts, very high resistance to crack growth may be obtained. Also, using FEM and comparing the size of the plastic zones, it was concluded that, although the tensile curves show nonlinearity, LEFM is still applicable for the printed parts.

Multi-objective optimization approach in design for additive manufacturing for fused deposition modeling

2019 ◽  
Vol 25 (5) ◽  
pp. 875-887
Author(s):  
Elnaz Asadollahi-Yazdi ◽  
Julien Gardan ◽  
Pascal Lafon
Keyword(s):  
Optimization Problem ◽  
Fused Deposition Modeling ◽  
Topological Optimization ◽  
Design For Additive Manufacturing ◽  
Multi Objective Optimization ◽  
Content Type ◽  
Fused Deposition ◽  
Design And Manufacturing ◽  
Deposition Modeling ◽  
Manufacturing Parameters

Purpose This paper aims to provide a multi-objective optimization problem in design for manufacturing (DFM) approach for fused deposition modeling (FDM). This method considers the manufacturing criteria and constraints during the design by selecting the best manufacturing parameters to guide the designer and manufacturer in fabrication with FDM. Design/methodology/approach Topological optimization and bi-objective optimization problems are suggested to complete the DFM approach for design for additive manufacturing (DFAM) to define a product. Topological optimization allows the shape improvement of the product through a material distribution for weight gain based on the desired mechanical behavior. The bi-objective optimization problem plays an important role to evaluate the manufacturability by quantification and optimization of the manufacturing criteria and constraint simultaneously. Actually, it optimizes the production time, required material regarding surface quality and mechanical properties of the product because of two significant parameters as layer thickness and part orientation. Findings A comprehensive analysis of the existing DFAM approaches illustrates that these approaches are not developed sufficiently in terms of manufacturability evaluation in quantification and optimization levels. There is no approach that investigates the AM criteria and constraints simultaneously. It is necessary to provide a decision-making tool for the designers and manufacturers to lead to better design and manufacturing regarding the different AM characteristics. Practical implications To assess the efficiency of this approach, a wheel spindle is considered as a case study which shows how this method is capable to find the best design and manufacturing solutions. Originality/value A multi-criteria decision-making approach as the main contribution is developed to analyze FDM technology and its attributes, criteria and drawbacks. It completes the DFAM approach for FDM through a bi-objective optimization problem which deals with finding the best manufacturing parameters by optimizing production time and material mass because of the product mechanical properties and surface roughness.

The influence of load direction, microstructure, raster orientation on the quasi-static response of fused deposition modeling ABS

2019 ◽  
Vol 25 (3) ◽  
pp. 462-472 ◽  
Author(s):  
Oluwakayode Bamiduro ◽  
Gbadebo Owolabi ◽  
Mulugeta A. Haile ◽  
Jaret C. Riddick
Keyword(s):  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Mechanical Response ◽  
Mechanical Performance ◽  
Bead Geometry ◽  
Static Response ◽  
Load Direction ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling

Purpose The continual growth of additive manufacturing has increased tremendously because of its versatility, flexibility and high customization of geometric structures. However, design hurdles are presented in understanding the relationship between the fabrication process and materials microstructure as it relates to the mechanical performance. The purpose of this paper is to investigate the role of build architecture and microstructure and the effects of load direction on the static response and mechanical properties of acrylonitrile butadiene styrene (ABS) specimens obtained via the fused deposition modeling (FDM) processing technique. Design/methodology/approach Among additive manufacturing processes, FDM is a prolific technology for manufacturing ABS. The blend of ABS combines strength, rigidity and toughness, all of which are desirable for the production of structural materials in rapid manufacturing applications. However, reported literature has varied widely on the mechanical performance due to the proprietary nature of the ABS material ratio, ultimately creating a design hurdle. While prior experimental studies have studied the mechanical response via uniaxial tension testing, this study has aimed to understand the mechanical response of ABS from the materials’ microstructural point of view. First, ABS specimen was fabricated via FDM using a defined build architecture. Next, the specimens were mechanically tested until failure. Then finally, the failure structures were microstructurally investigated. In this paper, the effects of microstructural evolution on the static mechanical response of various build architecture of ABS aimed at FDM manufacturing technique was analyzed. Findings The results show that the rastering orientation of 0/90 exhibited the highest tensile strength followed by fracture at its maximum load. However, the “45” bead direction of the ABS fibers displayed a cold-drawing behavior before rupture. The morphology analyses before and after tensile failure were characterized by a scanning electron microscopy (SEM) which highlighted the effects of bead geometry (layers) and areas of stress concentration such as interstitial voids in the material during build, ultimately compromising the structural integrity of the specimens. Research limitations/implications The ability to control the constituents and microstructure of a material during fabrication is significant to improving and predicting the mechanical performance of structural additive manufacturing components. In this report, the effects of microstructure on the mechanical performance of FDM-fabricated ABS materials was discussed. Further investigations are planned in understanding the effects of ambient environmental conditions (such as moisture) on the ABS material pre- and post-fabrication. Originality/value The study provides valuable experimental data for the purpose of understanding the inter-dependency between build parameters and microstructure as it relates to the specimens exemplified strength. The results highlighted in this study are fundamental to the development of optimal design of strength and complex ultra-lightweight structure efficiency.

Simulation of edge quality in fused deposition modeling

2019 ◽  
Vol 25 (3) ◽  
pp. 541-554 ◽  
Author(s):  
Antonio Armillotta
Keyword(s):  
Fused Deposition Modeling ◽  
Experimental Tests ◽  
Geometric Errors ◽  
Content Type ◽  
Fused Deposition ◽  
Graphical Simulation ◽  
Deposition Modeling ◽  
Edge Quality ◽  
Input Variables

Purpose The purpose of this paper is to propose a method for simulating the profile of part edges as a result of the FDM process. Deviations from nominal edge shape are predicted as a function of the layer thickness and three characteristic angles depending on part geometry and build orientation. Design/methodology/approach Typical patterns of edge profiles were observed on sample FDM parts and interpreted as the effects of possible toolpath generation strategies. An algorithm was developed to generate edge profiles consistent with the patterns expected for any combination of input variables. Findings Experimental tests confirmed that the simulation procedure can correctly predict basic geometric properties of edge profiles such as frequency, amplitude and shape of periodic asperities. Research limitations/implications The algorithm takes into account only a subset of the error causes recognized in previous studies. Additional causes could be integrated in the simulation to improve the estimation of geometric errors. Practical implications Edge simulation may help avoid process choices that result in aesthetic and functional defects on FDM parts. Originality/value Compared to the statistical estimation of geometric errors, graphical simulation allows a more detailed characterization of edge quality and a better diagnosis of error causes.

scholarly journals Numerical Simulation of the Fused Deposition Modeling for the Manufacturing of Parts with both High Geometric Fidelity and Mechanical Quality

2021 ◽  
Vol 14 (6) ◽  
pp. 712-725
Author(s):  
Holm Altenbach ◽  
◽  
G´abor Janiga ◽  
Rene Androsch ◽  
Mario Beiner ◽  
...  
Keyword(s):  
Fused Deposition Modeling ◽  
Two Dimensions ◽  
Volume Of Fluid Method ◽  
Ansys Fluent ◽  
Mechanical Parts ◽  
Fused Deposition ◽  
Modeling Process ◽  
Mechanical Quality ◽  
Deposition Modeling ◽  
Manufacturing Methods

With increasing usage of additive manufacturing methods for mechanical parts the need for precise and reliable simulations of the manufacturing process increases as well. In this paper various com- putations suited for simulating the fused deposition modeling process are considered in two dimensions. In fused deposition modeling a molten polymer is laid down on a prescribed path before the cooling of the melt begins. The occuring flows are treated as multiphase flows. To model the deposition of the filament, methods of computational fluid dynamics are used in ANSYS-Fluent, namely the volume of fluid method (VOF). Different numerical experiments are simulated

Deposition-induced effects of isotactic polypropylene and polycarbonate composites during fused deposition modeling

2017 ◽  
Vol 23 (5) ◽  
pp. 869-880 ◽  
Author(s):  
Ying-Guo Zhou ◽  
Bei Su ◽  
Lih-sheng Turng
Keyword(s):  
Mechanical Properties ◽  
Design Methodology ◽  
Fused Deposition Modeling ◽  
Content Type ◽  
Fused Deposition ◽  
Close Relationship ◽  
Molded Parts ◽  
Deposition Modeling ◽  
Injection Molded ◽  
First Time

Purpose Although the feasibility and effectiveness of the fused deposition modeling (FDM) method have been proposed and developed, studies of applying this technology to various materials are still needed for researching its applicability, especially with regard to polymer blends and composites. The purpose of this paper is to study the deposition-induced effect and the effect of compatibilizers on the mechanical properties of polypropylene and polycarbonate (PP/PC) composites. Design/methodology/approach For this purpose, three different deposition modes for PP/PC composites with or without compatibilizers were used for the FDM method and tested for tensile properties. Also, parts with the same materials were made by injection molding and used for comparison. In addition, different deposition speeds were used to investigate the different deposition-induced effects. Furthermore, the behavior of the mechanical properties was clarified with scanning electron microscope images of the fracture surfaces. Findings The research results suggest that the deposition orientation has a significant influence on the mechanical behavior of PP/PC composite FDM parts. The results also indicate that there is a close relationship between the mechanical properties and morphological structures which are deeply influenced by compatibilization. Compared with injection molded parts, the ductility of the FDM parts can be dramatically improved due to the formation of fibrils and micro-fibrils by the deposition induced during processing. Originality/value This is the first paper to investigate a PP/PC composite FDM process. The results of this paper verified the applicability of PP/PC composites to FDM technology. It is also the first time that the deposition-induced effect during FDM has been investigated and studied.

scholarly journals Edge quality in fused deposition modeling: I. Definition and analysis

2017 ◽  
Vol 23 (6) ◽  
pp. 1079-1087 ◽  
Author(s):  
Antonio Armillotta ◽  
Marco Cavallaro
Keyword(s):  
Fused Deposition Modeling ◽  
Experimental Tests ◽  
Geometric Errors ◽  
Geometric Accuracy ◽  
Process Map ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Geometric Variables ◽  
Physical Phenomena

Purpose The purpose of this paper is to discuss the problem of the geometric accuracy of edges in parts manufactured by the Fused Deposition Modeling process, as a preliminary step for an experimental investigation. Methodology/approach Three geometric variables (inclination, included and incidence angles) were defined for an edge. The influence of each variable on the geometric errors was explained with reference to specific causes related to physical phenomena and process constraints. Findings Occurrence conditions for all causes were determined and visualized in a process map, which was also developed into a software procedure for the diagnosis of quality issues on digital models of the parts. Research limitations/implications The process map was developed by only empirical considerations and does not allow to predict the amount of geometric errors. In the second part of the paper, experimental tests will help to extend and validate the prediction criteria. Practical implications As demonstrated by an example, the results allow to predict the occurrence of visible defects on the edges of a part before manufacturing it with a given build orientation. Originality/value In literature, the geometric accuracy of additively manufactured parts is only related to surface features. The paper shows that the quality of edges depends on additional variables and causes to be carefully controlled by process choices.

scholarly journals Fully resolved numerical simulations of fused deposition modeling. Part II – solidification, residual stresses and modeling of the nozzle

2018 ◽  
Vol 24 (6) ◽  
pp. 973-987 ◽  
Author(s):  
Huanxiong Xia ◽  
Jiacai Lu ◽  
Gretar Tryggvason
Keyword(s):  
Residual Stresses ◽  
Numerical Simulations ◽  
Fused Deposition Modeling ◽  
Fixed Bed ◽  
Ground Truth ◽  
Deposition Process ◽  
Material Behavior ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling

Purpose The purpose of this paper is to continue to describe the development of a comprehensive methodology for fully resolved numerical simulations of fused deposition modeling. Design/methodology/approach A front-tracking/finite volume method introduced in Part I to simulate the heat transfer and fluid dynamics of the deposition of a polymer filament on a fixed bed is extended by adding an improved model for the injection nozzle, including the shrinkage of the polymer as it cools down, and accounting for stresses in the solid. Findings The accuracy and convergence properties of the new method are tested by grid refinement, and the method is shown to produce convergent solutions for the shape of the filament, the temperature distribution, the shrinkage and the solid stresses. Research limitations/implications The method presented in the paper focuses on modeling the fluid flow, the cooling and solidification and volume changes and residual stresses, using a relatively simple viscoelastic constitutive model. More complex material models, depending, for example, on the evolution of the conformation tensor, are not included. Practical implications The ability to carry out fully resolved numerical simulations of the fused deposition process is expected to be critical for the validation of mathematical models for the material behavior, to help explore new deposition strategies and to provide the “ground truth” for the development of reduced-order models. Originality/value The paper completes describing the development of the first numerical method for fully resolved simulation of fused filament modeling.

Sign in / Sign up

Export Citation Format

Share Document