Robotica ◽  
2018 ◽  
Vol 37 (3) ◽  
pp. 502-520 ◽  
Author(s):  
Xianxi Luo ◽  
Shuhui Li ◽  
Shubo Liu ◽  
Guoquan Liu

SUMMARYThis paper presents an optimal trajectory planning method for industrial robots. The paper specially focuses on the applications of path tracking. The problem is to plan the trajectory with a specified geometric path, while allowing the position and orientation of the path to be arbitrarily selected within the specific ranges. The special contributions of the paper include (1) an optimal path tracking formulation focusing on the least time and energy consumption without violating the kinematic constraints, (2) a special mechanism to discretize a prescribed path integration for segment interpolation to fulfill the optimization requirements of a task with its constraints, (3) a novel genetic algorithm (GA) optimization approach that transforms a target path to be tracked as a curve with optimal translation and orientation with respect to the world Cartesian coordinate frame, (4) an integration of the interval analysis, piecewise planning and GA algorithm to overcome the challenges for solving the special trajectory planning and path tracking optimization problem. Simulation study shows that it is an insufficient condition to define a trajectory just based on the consideration that each point on the trajectory should be reachable. Simulation results also demonstrate that the optimal trajectory for a path tracking problem can be obtained effectively and efficiently using the proposed method. The proposed method has the properties of broad adaptability, high feasibility and capability to achieve global optimization.


IEEE Access ◽  
2021 ◽  
pp. 1-1
Author(s):  
Alejandro GutierreznGiles ◽  
Luis U. EvangelistanHernandez ◽  
Marco A. Arteaga ◽  
Carlos A. CruznVillar ◽  
Alejandro RodrigueznAngeles

Author(s):  
Aniruddha V. Shembekar ◽  
Yeo Jung Yoon ◽  
Alec Kanyuck ◽  
Satyandra K. Gupta

Additive manufacturing (AM) technologies have been widely used to fabricate 3D objects quickly and cost-effectively. However, building parts consisting of complex geometries with multiple curvatures can be a challenging process for the traditional AM system whose capability is restricted to planar-layered printing. Using 6-DOF industrial robots for AM overcomes this limitation by allowing materials to deposit on non-planar surfaces with desired tool orientation. In this paper, we present collision-free trajectory planning for printing using non-planar deposition. Trajectory parameters subject to surface curvature are properly controlled to avoid any collision with printing surface. We have implemented our approach by using a 6-DOF robot arm. The complex 3D structures with various curvatures were successfully fabricated, while avoiding any failures in joint movement, holding comparable build time and completing with a satisfactory surface finish.


2004 ◽  
Vol 23 (4) ◽  
pp. 703-715 ◽  
Author(s):  
T. Chettibi ◽  
H.E. Lehtihet ◽  
M. Haddad ◽  
S. Hanchi

Author(s):  
S.P. Wilson ◽  
M.C. Bartholomew-Biggs ◽  
S.C. Parkhurst

This chapter describes the formulation and solution of a multi-aircraft routing problem which is posed as a global optimization calculation. The chapter extends previous work (involving a single aircraft using two dimensions) which established that the algorithm DIRECT is a suitable solution technique. The present work considers a number of ways of dealing with multiple routes using different problem decompositions. A further enhancement is the introduction of altitude to the problems so that full threedimensional routes can be produced. Illustrative numerical results are presented involving up to three aircraft and including examples which feature routes over real-life terrain data.


2021 ◽  
Author(s):  
Li Chen ◽  
Wenyun Lu ◽  
Lin Wang ◽  
Xi Xing ◽  
Xin Teng ◽  
...  

AbstractA primary goal of metabolomics is to identify all biologically important metabolites. One powerful approach is liquid chromatography-high resolution mass spectrometry (LC-MS), yet most LC-MS peaks remain unidentified. Here, we present a global network optimization approach, NetID, to annotate untargeted LC-MS metabolomics data. We consider all experimentally observed ion peaks together, and assign annotations to all of them simultaneously so as to maximize a score that considers properties of peaks (known masses, retention times, MS/MS fragmentation patterns) as well network constraints that arise based on mass difference between peaks. Global optimization results in accurate peak assignment and trackable peak-peak relationships. Applying this approach to yeast and mouse data, we identify a half-dozen novel metabolites, including thiamine and taurine derivatives. Isotope tracer studies indicate active flux through these metabolites. Thus, NetID applies existing metabolomic knowledge and global optimization to annotate untargeted metabolomics data, revealing novel metabolites.


Sign in / Sign up

Export Citation Format

Share Document