Design Considerations for Output Capacitance Under Inductance Mismatches in Multiphase Buck Converters

This paper studies the effect of interleaving operation on the bifurcation behavior in a system of parallel-connected dc/dc buck converters. Simulations and analysis are presented for both the cases of interleaving and synchronous operations. The effects of variation of some chosen parameters on the bifurcation behavior of the system are captured. In particular, it is found that variation of the voltage feedback gains leads to period-doubling bifurcation. Interleaving operation will discourage the occurrence of this bifurcation by widening the stable region. It is also observed that variation of output capacitance, load or switching period leads to Neimark–Sacker bifurcation. Interleaving operation will make this bifurcation more likely to occur by narrowing the stable region. In order to show the effect of interleaving operation, bifurcation boundaries of stable period-1 operation in the two cases are located and compared.

Download Full-text

Morphological behavior of compatibilized ternary blends prepared by mechanical mixing

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100151830 ◽

1993 ◽

Vol 51 ◽

pp. 1200-1201

Author(s):

S.D. Smith ◽

R.J. Spontak ◽

D.H. Melik ◽

S.M. Buehler ◽

K.M. Kerr ◽

...

Keyword(s):

Interfacial Adhesion ◽

Diblock Copolymers ◽

Ternary Blends ◽

Mechanical Mixing ◽

Design Considerations ◽

Covalently Bonded ◽

Homopolymer Blends ◽

Emulsifying Agent ◽

Surface Active ◽

Low Entropy

When blended together, homopolymers A and B will normally macrophase-separate into relatively large (≫1 μm) A-rich and B-rich phases, between which exists poor interfacial adhesion, due to a low entropy of mixing. The size scale of phase separation in such a blend can be reduced, and the extent of interfacial A-B contact and entanglement enhanced, via addition of an emulsifying agent such as an AB diblock copolymer. Diblock copolymers consist of a long sequence of A monomers covalently bonded to a long sequence of B monomers. These materials are surface-active and decrease interfacial tension between immiscible phases much in the same way as do small-molecule surfactants. Previous studies have clearly demonstrated the utility of block copolymers in compatibilizing homopolymer blends and enhancing blend properties such as fracture toughness. It is now recognized that optimization of emulsified ternary blends relies upon design considerations such as sufficient block penetration into a macrophase (to avoid block slip) and prevention of a copolymer multilayer at the A-B interface (to avoid intralayer failure).

Download Full-text

Theoretical And Practical Design Considerations for Ultra-High Resolution Electron Lenses

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s1431927600001161 ◽

1980 ◽

Vol 38 ◽

pp. 266-269

Author(s):

Y. Harada ◽

K. Tsuno ◽

Y. Arai

Keyword(s):

Optical Properties ◽

High Resolution ◽

Chromatic Aberration ◽

Point Of View ◽

Pole Piece ◽

Axial Field ◽

Design Considerations ◽

Resolution Electron ◽

Practical Design ◽

Peak Flux

Magnetic objective lenses, from the point of view of pole piece geometry, can he roughly classified into two types, viz., symmetrical and asymmetrical. In the case of the former, the optical properties have been calculated by several authors1-3) and the results would appear to suggest that, in order to reduce the spherical and chromatic aberration coefficients, Cs and Cc, it is necessary to decrease the half-width value of the axial field distribution and to increase the peak flux density. The expressions for either minimum Cs or minimum Cc were presented in the form of ‘universal’ curves by Mulvey and Wallington4).

Download Full-text