scholarly journals The Investigation of Wind Energy Potential in Order to Estimate Power Plants in Baladeh Mazandaran, Iran

2012 ◽  
pp. 29-33
Author(s):  
S. Asghar Gholamian ◽  
S. Bagher Soltani ◽  
R. Ilka

First step for achieving wind energy is to locate points with appropriate wind power density in a country. Wind data which are recorded in a synoptic weather station, are the best way to study the wind potential of an area. In this paper wind speed period of Baladeh synoptic weather station is studied, since it has the maximum average of wind speed among 15 stations of the MAZANDARAN Province. Weibull factors k and c are calculated for 40 months from September 2006 to December 2009 and wind power density is determined based on these data. The total average of factors k and c for a height for 50 m are 1.442 m/s and 5.1256 respectively. By using the average of factors, wind power density in 50 m height will be 147.40 watt/m2 which is categorized as weak potential in wind class. However by monthly investigation it is shown that with a 50 m wind, this station can be put in medium class in hot months of the year.

2019 ◽  
Vol 38 (1) ◽  
pp. 175-200 ◽  
Author(s):  
Shafiqur Rehman ◽  
Narayanan Natarajan ◽  
Mangottiri Vasudevan ◽  
Luai M Alhems

Wind energy is one of the abundant, cheap and fast-growing renewable energy sources whose intensive extraction potential is still in immature stage in India. This study aims at the determination and evaluation of wind energy potential of three cities located at different elevations in the state of Tamil Nadu, India. The historical records of wind speed, direction, temperature and pressure were collected for three South Indian cities, namely Chennai, Erode and Coimbatore over a period of 38 years (1980-2017). The mean wind power density was observed to be highest at Chennai (129 W/m2) and lowest at Erode (76 W/m2) and the corresponding mean energy content was highest for Chennai (1129 kWh/m2/year) and lowest at Erode (666 kWh/m2/year). Considering the events of high energy-carrying winds at Chennai, Erode and Coimbatore, maximum wind power density were estimated to be 185 W/m2, 190 W/m2 and 234 W/m2, respectively. The annual average net energy yield and annual average net capacity factor were selected as the representative parameters for expressing strategic wind energy potential at geographically distinct locations having significant variation in wind speed distribution. Based on the analysis, Chennai is found to be the most suitable site for wind energy production followed by Coimbatore and Erode.


Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1846 ◽  
Author(s):  
Teklebrhan Negash ◽  
Erik Möllerström ◽  
Fredric Ottermo

This paper presents the wind energy potential and wind characteristics for 25 wind sites in Eritrea, based on wind data from the years 2000–2005. The studied sites are distributed all over Eritrea, but can roughly be divided into three regions: coastal region, western lowlands, and central highlands. The coastal region sites have the highest potential for wind power. An uncertainty, due to extrapolating the wind speed from the 10-m measurements, should be noted. The year to year variations are typically small and, for the sites deemed as suitable for wind power, the seasonal variations are most prominent in the coastal region with a peak during the period November–March. Moreover, Weibull parameters, prevailing wind direction, and wind power density recalculated for 100 m above ground are presented for all 25 sites. Comparing the results to values from the web-based, large-scale dataset, the Global Wind Atlas (GWA), both mean wind speed and wind power density are typically higher for the measurements. The difference is especially large for the more complex-terrain central highland sites where GWA results are also likely to be more uncertain. The result of this study can be used to make preliminary assessments on possible power production potential at the given sites.


2020 ◽  
pp. 014459872092074 ◽  
Author(s):  
Muhammad Sumair ◽  
Tauseef Aized ◽  
Syed Asad Raza Gardezi ◽  
Syed Ubaid Ur Rehman ◽  
Syed Muhammad Sohail Rehman

Current work focusses on the wind potential assessment in South Punjab. Eleven locations from South Punjab have been analyzed using two-parameter Weibull model (with Energy Pattern Factor Method to estimate Weibull parameters) and five years (2014–2018) hourly wind data measured at 50 m height and collected from Pakistan Meteorological Department. Techno-economic analysis of energy production using six different turbine models was carried out with the purpose of presenting a clear picture about the importance of turbine selection at particular location. The analysis showed that Rahim Yar Khan carries the highest wind speed, highest wind power density, and wind energy density with values 4.40 ms−1, 77.2 W/m2 and 677.76 kWh/m2/year, respectively. On the other extreme, Bahawalnagar observes the least wind speed i.e. 3.60 ms−1 while Layyah observes the minimum wind power density and wind energy density as 38.96 W/m2 and 352.24 kWh/m2/year, respectively. According to National Renewable Energy Laboratory standards, wind potential ranging from 0 to 200 W/m2 is considered poor. Economic assessment was carried out to find feasibility of the location for energy harvesting. Finally, Polar diagrams drawn to show the optimum wind blowing directions shows that optimum wind direction in the region is southwest.


2021 ◽  
Vol 8 (2) ◽  
Author(s):  
Alhassan A. Teyabeen ◽  
Fathi R. Akkari ◽  
Ali E. Jwaid ◽  
Ashraf Zaghwan ◽  
Rehab Abodelah

To assess the wind energy potential at any site, the wind power density should be estimated; it evaluates the wind resource and indicates the amount of available wind energy. The purpose of this study is to estimate the monthly and annual wind power density based on the Weibull distribution using wind speed data collected in Zwara, Libya during 2007. The wind date are measured at the three hub heights of 10m, 30m, and 50m above ground level, and recorded every 10 minutes. The analysis showed that the annual average wind speed are 4.51, 5.86, 6.26 m/s for the respective mentioned heights. The average annual wind power densities at the mentioned heights were 113.71, 204.19, 243.48 , respectively.


2020 ◽  
Author(s):  
Chris G. Tzanis ◽  
Kostas Philippopoulos ◽  
Constantinos Cartalis ◽  
Konstantinos Granakis ◽  
Anastasios Alimissis ◽  
...  

<p>Energy production from the utilization of wind energy potential depends on the variability of the wind field as determined by the interaction of natural processes on different scales. Global climate change can cause alterations in the surface wind and thus it may affect the geographical distribution and the wind energy potential variability. Wind energy production is sensitive to wind speed changes, especially in the upper percentile of the wind speed distributions, where energy production is more effective. The importance of wind energy production changes is enhanced by the fact that wind energy investments are long-term and are characterized by high initial costs and low operating costs. In the present study, these changes are examined for the southeastern Mediterranean region, based on simulations of the Regional Climate Model ALADIN 5.2 extracted from the Med-CORDEX database for the climatic scenarios RCP4.5 and RCP8.5. The results indicate a wind power density increase over the Aegean Sea, the Ionian Sea, the Dardanelles and the Black Sea, with similar levels of increase for both climatic scenarios. In contrast, during the winter period there is a decline across the southeastern Mediterranean, which is more significant in the case of the RCP8.5 scenario. Finally, for most areas of eastern Greece, there is a reduction in the number of wind speed cases for both below and above cut-in and cut-out wind speeds, while there is an increase in the number of wind speed cases that wind turbines operate at their maximum power. The results are expected to reduce the uncertainty associated with the impact of climate change on wind energy production. </p>


2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
N. Laban Ongaki ◽  
Christopher M. Maghanga ◽  
Joash Kerongo

Background. Global warming is a growing threat in the world today mainly due to the emission of CO2 caused by the burning of fossil fuel. Consequently, countries are being forced to seek potential alternative sources of energy such as wind, solar, and photovoltaic among many others. However, the realization of their benefits is faced with challenges. Though wind stands a chance to solve this problem, the lack of adequate site profiles, long-term behavioural information, and specific data information that enables informed choice on site selection, turbine selection, and expected power output has remained a challenge to its exploitation. In this research, Weibull and Rayleigh models are adopted. Wind speeds were analyzed and characterized in the short term and then simulated for a long-term measured hourly series data of daily wind speeds at a height of 10 m. The analysis included daily wind data which was grouped into discrete data and then calculated to represent the mean wind speed, diurnal variations, daily variations, and monthly variations. To verify the models, statistical tools of Chi square, RMSE, MBE, and correlational coefficient were applied. Also, the method of measure, correlate, and predict was adopted to check for the reliability of the data used. The wind speed frequency distribution at the height of 10 m was found to be 2.9 ms-1 with a standard deviation of 1.5. From the six months’ experiments, averages of wind speeds at hub heights of 10 m were calculated and found to be 1.7 m/s, 2.4 m/s, and 1.3 m/s, for Ikobe, Kisii University, and Nyamecheo stations, respectively. The wind power density of the region was found to be 29 W/m2. By a narrow margin, Rayleigh proves to be a better method over Weibull in predicting wind power density in the region. Wind speeds at the site are noted to be decreasing over the years. The region is shown as marginal on extrapolation to 30 m for wind energy generation hence adequate for nongrid connected electrical and mechanical applications. The strong correlation between the site wind profiles proves data reliability. The gradual decrease of wind power over the years calls for attention.


2021 ◽  
pp. 0309524X2110438
Author(s):  
Carlos Méndez ◽  
Yusuf Bicer

The present study analyzes the wind energy potential of Qatar, by generating a wind atlas and a Wind Power Density map for the entire country based on ERA-5 data with over 41 years of measurements. Moreover, the wind speeds’ frequency and direction are analyzed using wind recurrence, Weibull, and wind rose plots. Furthermore, the best location to install a wind farm is selected. The results indicate that, at 100 m height, the mean wind speed fluctuates between 5.6054 and 6.5257 m/s. Similarly, the Wind Power Density results reflect values between 149.46 and 335.06 W/m2. Furthermore, a wind farm located in the selected location can generate about 59.7437, 90.4414, and 113.5075 GWh/y electricity by employing Gamesa G97/2000, GE Energy 2.75-120, and Senvion 3.4M140 wind turbines, respectively. Also, these wind farms can save approximately 22,110.80, 17,617.63, and 11,637.84 tons of CO2 emissions annually.


Author(s):  
A. A. Yahaya ◽  
I. M. Bello ◽  
N. Mudassir ◽  
I. Mohammed ◽  
M. I. Mukhtar

One of the major developments in the technology today is the wind turbine that generates electricity and feed it directly to the grid which is used in many part of the world. The main purpose of this work is to determine the wind potential for electricity generation in Aliero, Kebbi state. Five years Data (2014-2018) was collected from the metrological weather station (Campell Scientific Model), the equipment installed at Kebbi State University of Science And Technology Aliero The data was converted to monthly and annual averages, and compared with the threshold average wind speed values that can only generate electricity in both vertical and horizontal wind turbines. The highest average wind speed 2.81 m/s was obtained in the month of January and the minimum average wind speed of 1.20 m/s in the month of October. Mean annual wind speed measured in the study area shows that there has been an increase in the wind speed from 2014 which peaked in 2015 and followed by sudden decrease to a minimum seasonal value in the year 2016. The highest wind direction is obtained from the North North-East (NNE) direction. From the results of wind power density it shows that we have highest wind power density in month of January and December with  0.8635 w/ m2 and 0.8295 w/ m2 respectively, while lowest wind power density in the month of October and September with 0.6780 w/ m2 and 0.6575 w/ m2  respectively. Result of the type Wind Turbine to be selected in the study area shows that the site is not viable for power generation using a horizontal wind turbine but the vertical wind turbine will be suitable for the generation of electricity.


2020 ◽  
Vol 38 (5) ◽  
pp. 1893-1913
Author(s):  
Carlos Méndez ◽  
Yusuf Bicer

This study analyzes the feasibility of satisfying the demand of three Football Stadiums for the 2022 FIFA World Cup in Qatar, using the wind’s kinetic energy. For all three selected locations (Lusail, Al Rayyan, and Al Wakrah), the wind potentiality is calculated through an environmental parameters study, from which the wind power density is obtained. Furthermore, a commercial wind turbine with proper characteristics is selected, and the same case study for each location is presented, to quantify the capacity that wind energy offers for satisfying the maximum energy demand of each associated stadium. In addition, the environmental benefits and the time required by each wind farm to satisfy the energy demand are computed. The results reveal that the conditions enable the use of wind energy for this purpose, based on a 5.06 m/s, 4.63 m/s, and 5.18 m/s velocity mean for Lusail, Al Rayyan, and Al Wakrah, respectively; from which values of 187.49 W/m2, 150.96 W/m2, and 187.29 W/m2 of wind power density are obtained. Also, the proposed wind farms could produce 69,952.56 MWh/year, 59,550.19 MWh/year, and 75,333.70 MWh/year, respectively. Moreover, the wind farms should produce energy for a period of 5.64 h, 4.41 h, and 5.23 h, to satisfy the maximum demand by a football match in its associated location. Additionally, to avoid the implementation of a storage system, the electricity obtained from the wind is connected to the power grid, decreasing the quota of fossil fuel power plants. In consequence, Qatar will eliminate the emissions of approximately 23.376 tons of CO2 in total per trio of matches held in these stadiums. Finally, a post 2022 FIFA World Cup scenario is analyzed, obtaining a positive outcome from both environmental and economic perspectives, in which an average of 14,675 tons of CO2 and 6.03 Million US$ can be saved annually.


2015 ◽  
Vol 785 ◽  
pp. 621-626
Author(s):  
R. Shamsipour ◽  
M. Fadaeenejad ◽  
M.A.M. Radzi

In this study, wind energy potential in three different stations in Malaysia in period of 5 years is analyzed. Base on Weibull distribution parameters, the mean wind speed, wind power density and wind energy density is estimated for each defined location. Although there are many works about wind potential in Malaysia, however a few of them have been provided a comprehensive study about wind power in different places in Malaysia. According to the findings, the annual mean wind speeds indicates that the highest wind speed variation is about 2 m/s and is belonged to the Subang station and the highest wind speed is 3.5 m/s in in Kudat. It is also found that the maximum wind power densities among these three sites are 22 W/m2, 24 W/m2 and 22 W/m2 in Kudat station in January, February and September respectively. The results of the study show that as the second parameter for Weibull model, the highest wind energy density has been 190 kWh/m2 per year in Kudat and the lowest one has been about 60 kWh/m2 in Kuching.


Sign in / Sign up

Export Citation Format

Share Document