Effects of Heat Release Mode on Emissions and Efficiencies of a Compound Diesel Homogeneous Charge Compression Ignition Combustion Engine

2005 ◽  
Vol 128 (2) ◽  
pp. 446-454 ◽  
Author(s):  
Wanhua Su ◽  
Xiaoyu Zhang ◽  
Tiejian Lin ◽  
Yiqiang Pei ◽  
Hua Zhao
Keyword(s):  
Heat Release ◽  
Thermal Efficiency ◽  
Homogeneous Charge Compression Ignition ◽  
Experimental Comparison ◽  
Injection Timing ◽  
Compression Ignition ◽  
Multiple Injection ◽  
Hcci Combustion ◽  
Flexible Mode ◽  
Homogeneous Charge

A compound diesel homogeneous charge compression ignition (HCCI) combustion system has been developed based on the combined combustion strategies of multiple injection strategy and a mixing enhanced combustion chamber design. In this work, a STAR-CD based, multidimensional modeling is conducted to understand and optimize the multiple injection processes. The parameters explored included injection timing, dwell time, and pulse width. Insight generated from this study provides guidelines on designing the multipulse injection rate pattern for optimization of fuel-air mixing. Various heat release modes created by different injection strategies are investigated by experimental comparison of combustion efficiency, heat loss, and thermal efficiency. It is demonstrated that the process of fuel evaporation and mixing are strongly influenced by pulse injection parameters. Through control of the parameters, the stratification and autoignition of the premixed mixture, and the heat release mode can be controlled. The dispersed mode of heat release created only by the compound diesel HCCI combustion is a flexible mode in combustion control. The thermal efficiency with this mode can reach approximately to as high as that of conventional diesel combustion, while the NOx and smoke emissions can be reduced simultaneously and remarkably.

A new heat release rate (HRR) law for homogeneous charge compression ignition (HCCI) combustion mode

2009 ◽  
Vol 29 (17-18) ◽  
pp. 3654-3662 ◽  
Author(s):  
Miguel Torres García ◽  
Francisco José Jiménez-Espadafor Aguilar ◽  
Tomás Sánchez Lencero ◽  
José Antonio Becerra Villanueva
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Homogeneous Charge Compression Ignition ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Hcci Combustion ◽  
Homogeneous Charge

Effects of Multi-Injection Mode on Diesel Homogeneous Charge Compression Ignition Combustion

2006 ◽  
Vol 129 (1) ◽  
pp. 230-238 ◽  
Author(s):  
Wanhua Su ◽  
Bin Liu ◽  
Hui Wang ◽  
Haozhong Huang
Keyword(s):  
Thermal Efficiency ◽  
Homogeneous Charge Compression Ignition ◽  
Fuel Injection ◽  
Direct Injection ◽  
Progressive Increase ◽  
Compression Ignition ◽  
Injection Mode ◽  
Hcci Combustion ◽  
Injection Modes ◽  
Homogeneous Charge

Early injection, well before top dead center (TDC), has perhaps been the most commonly investigated approach to obtain homogeneous charge compression ignition (HCCI) combustion in a direct-injection (DI) diesel engine. However, wall wetting due to overpenetration of the fuel spray can lead to unacceptable amounts of unburned fuel and removal of lubrication oil. Another difficulty of diesel HCCI combustion is the control of combustion phasing. In order to overcome these difficulties, a multipulse fuel injection technology has been developed for the purpose of organizing diesel HCCI combustion, by which the injection width, injection number, and the dwell time between two neighboring pulse injections can be flexibly regulated. In present paper, the effects of a series of multipulse injection modes realized based on the prejudgment of combustion requirement, on engine emissions, thermal efficiency, and cycle fuel energy distribution of diesel HCCI combustion are studied. The designed injection modes include so-called even mode, hump mode, and progressive increase mode, and each mode with five and six pulses, respectively. Engine test was conducted with these modes. The experimental results show that diesel HCCI combustion is extremely sensitive to multipulse injection modes and that thermal efficiency can be improved with carefully modulated ones. There are many modes that can reach near zero NOx and smoke emissions, but it is significant to be aware that multipulse injection mode must be carefully designed for higher thermal efficiency.

Residual-effected homogeneous charge compression ignition at a low compression ratio using exhaust reinduction

2003 ◽  
Vol 4 (3) ◽  
pp. 163-177 ◽  
Author(s):  
P. A. Caton ◽  
A. J. Simon ◽  
J. C. Gerdes ◽  
C. F. Edwards
Keyword(s):  
Compression Ratio ◽  
Equivalence Ratio ◽  
Homogeneous Charge Compression Ignition ◽  
Compression Ignition ◽  
Single Digit ◽  
Hcci Combustion ◽  
Actuation System ◽  
Order Of Magnitude ◽  
No Emissions ◽  
Homogeneous Charge

Studies have been conducted to assess the performance of homogeneous charge compression ignition (HCCI) combustion initiated by exhaust reinduction from the previous engine cycle. Reinduction is achieved using a fully flexible electrohydraulic variable-valve actuation system. In this way, HCCI is implemented at low compression ratio without throttling the intake or exhaust, and without preheating the intake charge. By using late exhaust valve closing and late intake valve opening strategies, steady HCCI combustion was achieved over a range of engine conditions. By varying the timing of both valve events, control can be exerted over both work output (load) and combustion phasing. In comparison with throttled spark ignition (SI) operation on the same engine, HCCI achieved 25–55 per cent of the peak SI indicated work, and did so at uniformly higher thermal efficiency. This was accompanied by a two order of magnitude reduction in NO emissions. In fact, single-digit (ppm) NO emissions were realized under many load conditions. In contrast, hydrocarbon emissions proved to be significantly higher in HCCI combustion under almost all conditions. Varying the equivalence ratio showed a wider equivalence ratio tolerance at low loads for HCCI.

Decreasing hydrocarbon and carbon monoxide emissions of a natural-gas engine operating in the quasi-homogeneous charge compression ignition mode at low loads

2005 ◽  
Vol 219 (9) ◽  
pp. 1125-1131 ◽  
Author(s):  
Su Ling ◽  
Zhou Longbao ◽  
Liu Shenghua ◽  
Zhong Hui
Keyword(s):  
Carbon Monoxide ◽  
Natural Gas ◽  
Thermal Efficiency ◽  
Homogeneous Charge Compression Ignition ◽  
Compression Ignition ◽  
Brake Thermal Efficiency ◽  
Pilot Fuel ◽  
Cng Engine ◽  
Standard Mode ◽  
Homogeneous Charge

Experimental studies have been carried out on decreasing the hydrocarbon (HC) and carbon monoxide (CO) emissions of a compressed natural-gas (CNG) engine operating in quasi-homogeneous charge compression ignition (QHCCI) mode at low loads. The effects of three technical approaches including partial gas cut-off (PGC), intake air throttling, and increasing the pilot fuel quantity on emissions and the brake thermal efficiency of the CNG engine are studied. The results show that HC and CO emissions can be reduced with only a small penalty on the brake thermal efficiency. An increase in the brake thermal efficiency and reductions in HC and CO emissions can be simultaneously realized by increasing the pilot fuel quantity. It is also indicated from experiments that the HC and CO emissions of the engine can be effectively reduced when using intake air throttling and increasing the pilot fuel quantity are both adopted. However, nitrogen oxide (NOx) emissions increase with increase in the throttling and the pilot fuel quantity. Under PGC conditions, NOx emissions are lower than those in the standard mode; however, they increase and exceed the values in the standard mode in increases in the load and natural-gas supply.

Characterizing the cyclic variability of ignition timing in a homogeneous charge compression ignition engine fuelled with n-heptane/iso-octane blend fuels

2008 ◽  
Vol 9 (5) ◽  
pp. 361-397 ◽  
Author(s):  
M Shahbakhti ◽  
C R Koch
Keyword(s):  
Equivalence Ratio ◽  
Homogeneous Charge Compression Ignition ◽  
Coolant Temperature ◽  
Cyclic Variation ◽  
Compression Ignition ◽  
Ignition Timing ◽  
Compression Ignition Engine ◽  
Hcci Combustion ◽  
Cyclic Variations ◽  
Homogeneous Charge

The cyclic variations of homogeneous charge compression ignition (HCCI) ignition timing is studied for a range of charge properties by varying the equivalence ratio, intake temperature, intake pressure, exhaust gas recirculation (EGR) rate, engine speed, and coolant temperature. Characterization of cyclic variations of ignition timing in HCCI at over 430 operating points on two single-cylinder engines for five different blends of primary reference fuel (PRF), (iso-octane and n-heptane) is performed. Three distinct patterns of cyclic variation for the start of combustion (SOC), combustion peak pressure ( Pmax), and indicated mean effective pressure (i.m.e.p.) are observed. These patterns are normal cyclic variations, periodic cyclic variations, and cyclic variations with weak/misfired ignitions. Results also show that the position of SOC plays an important role in cyclic variations of HCCI combustion with less variation observed when SOC occurs immediately after top dead centre (TDC). Higher levels of cyclic variations are observed in the main (second) stage of HCCI combustion compared with that of the first stage for the PRF fuels studied. The sensitivity of SOC to different charge properties varies. Cyclic variation of SOC increases with an increase in the EGR rate, but it decreases with an increase in equivalence ratio, intake temperature, and coolant temperature.

Active valvetrain for homogeneous charge compression ignition

2005 ◽  
Vol 6 (4) ◽  
pp. 377-397 ◽  
Author(s):  
N Milovanovic ◽  
J G W Turner ◽  
S A Kenchington ◽  
G Pitcher ◽  
D W Blundell
Keyword(s):  
Homogeneous Charge Compression Ignition ◽  
Cold Start ◽  
Smooth Transition ◽  
Engine Management System ◽  
Compression Ignition ◽  
Load Range ◽  
Hcci Combustion ◽  
Particulate Matter Emissions ◽  
Mode Transitions ◽  
Homogeneous Charge

Homogeneous charge compression ignition (HCCI), also known as controlled autoignition (CAI) or the premixed charge compression ignition (PCCI) engine concept, has the potential to be highly efficient and to produce low NOx, carbon dioxide, and particulate matter emissions. However, it experiences problems with cold start in a gasoline HCCI engine, running at idle and at high loads, which, together with controlling the combustion over the entire speed/load range, limits its practical application. A way to overcome these problems is to operate the engine in ‘hybrid mode’, where the engine operates in HCCI mode at low, medium, and cruising loads and can switch to or from spark ignition (SI) or diesel (CI) mode for a cold start, idle, and higher loads. Such an engine will have frequent changes in engine load and speeds and therefore frequent transitions between HCCI and SI combustion modes. The valvetrain and engine management system (EMS) have to provide a successful control of HCCI mode and a fast and smooth transition keeping all relevant engine parameters within an acceptable range. Consequently, this leads to high demands on the valvetrain and therefore a need for a very high degree of flexibility. The aim of this paper is to present the potential of a fully variable valvetrain (FVVT) system, the Lotus active valvetrain (AVT™), for controlling HCCI combustion and enabling fast and smooth mode transitions in a HCCI/SI engine fuelled with commercially available gasoline (95 RON) and in a HCCI/DI engine fuelled with diesel (50 CN) fuel.

Combustion and emission characteristics of a homogeneous charge compression ignition engine

2005 ◽  
Vol 219 (9) ◽  
pp. 1133-1139 ◽  
Author(s):  
Hu Tiegang ◽  
Liu Shenghua ◽  
Zhou Longbao ◽  
Zhu Chi
Keyword(s):  
Heat Release ◽  
Homogeneous Charge Compression Ignition ◽  
Cetane Number ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Hcci Engine ◽  
Homogeneous Charge

Dimethyl ether (DME) is a kind of fuel with high cetane number and low evaporating temperature, which is suitable for a homogeneous charge compression ignition (HCCI) engine. The combustion and emission characteristics of an HCCI engine fuelled with DME were investigated on a modified single-cylinder engine. The experimental results indicate that the HCCI engine combustion is a two-stage heat release process. The engine load or air-fuel ratio has significant effects on the maximum cylinder pressure and its position, the shape of the pressure rise rate and the heat release rate. The engine speed has little effect. A DME HCCI engine is smoke free, with zero NOx and low hydrocarbon and CO emissions under the operating conditions of 0.25–0.30 MPa brake mean effective pressure.

Sign in / Sign up

Export Citation Format

Share Document