Numerical Study of the Injection Process in a Transonic Wind Tunnel—Part I: The Design Point

2006 ◽  
Vol 129 (6) ◽  
pp. 682-694 ◽  
Author(s):  
João B. P. Falcão Filho ◽  
Marcos A. Ortega
Keyword(s):  
Wind Tunnel ◽  
Numerical Study ◽  
Research Effort ◽  
Three Dimensional ◽  
Numerical Code ◽  
Navier Stokes ◽  
Main Stream ◽  
Design Point ◽  
Injection Process ◽  
Transonic Wind Tunnel

Injectors are to be installed in a transonic wind tunnel with the ultimate objective of expanding the Reynolds number envelope. The aim of this research effort is to numerically simulate the steady mixing process involving the supersonic jets and the tunnel subsonic main stream. A three-dimensional, Reynolds-averaged Navier–Stokes numerical code was developed following the main lines of the finite-difference diagonal algorithm, and turbulence effects are accounted for through the use of the Spalart and Allmaras one-equation scheme. This paper focuses on the “design point” of the tunnel, which establishes (among other specifications) that the static pressures of both streams at the entrance of the injection chamber are equal. Three points are worth noting. The first is related to the numerical strategy that was introduced in order to mimic the real physical process in the entire circuit of the tunnel. The second corresponds to the solution per se of the three-dimensional mixing between several supersonic streams and the subsonic main flow. The third is the calculation of the “engineering” parameters, that is, the injection loss factor, gain, and efficiency. Many interesting physical aspects are discussed, and among them, the formation of three-dimensional shocks’ and expansions’ “domes”

scholarly journals Numerical Contribution to Airflow Study Through a Generic Merchant Ship Models

2020 ◽  
Vol 15 ◽  
Keyword(s):  
Wind Tunnel ◽  
Numerical Study ◽  
Three Dimensional ◽  
Numerical Results ◽  
Numerical Code ◽  
Generic Models ◽  
Merchant Ship ◽  
Acceleration And Deceleration ◽  
Low Speed Wind Tunnel ◽  
Good Agreement

The merchant ships are continuously recruited by the world meteorological organization (WMO) as Voluntary Observing Ship (VOS) for the collect of meteorological parameters at the ocean surface. VOS meteorological observation includes many parameters such as the wind speed measured by anemometers. This measurement is biased by the presence of ship and superstructure. Little work was carried out in this field. Between them we find the experimental work at a low speed wind tunnel of Southampton University which studies the airflow distortion over simple models (generic models) of VOS merchant ship. This study presents numerical results of a 3D simulation analyzing airflow effect above the bridge of a generic merchant ship models involved in VOS. For this purpose three-dimensional, stationary and turbulent, numerical simulation has been achieved the flow over the bridge of a tanker and a container ship at 1/ 46 scale using a numerical code and CFX code with turbulence k-ε models. This numerical study allows us to know the position of the line of equality as well as the zone of acceleration and deceleration of the flow. The results obtained numerically by numerical code and CFX code are compared with those obtained experimentally in the wind tunnel of Southampton University. Numerical results are in a good agreement with experimental results and can be used as a reference to find the position of the equality line and to know the error range in of the anemometer velocity reading.

scholarly journals Dynamics of Single Droplet Splashing on Liquid Film by Coupling FVM with VOF

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 841
Author(s):  
Yuzhen Jin ◽  
Huang Zhou ◽  
Linhang Zhu ◽  
Zeqing Li
Keyword(s):  
Liquid Film ◽  
Weber Number ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Single Droplet ◽  
Navier Stokes Equations ◽  
Volume Method ◽  
The Relationship

A three-dimensional numerical study of a single droplet splashing vertically on a liquid film is presented. The numerical method is based on the finite volume method (FVM) of Navier–Stokes equations coupled with the volume of fluid (VOF) method, and the adaptive local mesh refinement technology is adopted. It enables the liquid–gas interface to be tracked more accurately, and to be less computationally expensive. The relationship between the diameter of the free rim, the height of the crown with different numbers of collision Weber, and the thickness of the liquid film is explored. The results indicate that the crown height increases as the Weber number increases, and the diameter of the crown rim is inversely proportional to the collision Weber number. It can also be concluded that the dimensionless height of the crown decreases with the increase in the thickness of the dimensionless liquid film, which has little effect on the diameter of the crown rim during its growth.

A CFD-Based Parametric Study on Modification of Discrete Sister Holes Location for the Film Cooling Flow

2014 ◽  
Author(s):  
Siavash Khajehhasani ◽  
Bassam Jubran
Keyword(s):  
Film Cooling ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Base Case ◽  
Spanwise Direction ◽  
Cooling Performance ◽  
Cooling Flow ◽  
Lift Off ◽  
The Individual

A numerical study on the effects of sister holes locations on film cooling performance is presented. This includes the change of the location of the individual discrete sister holes in the streamwise and spanwise directions, where each one of these directions includes 9 different locations, The simulations are performed using three-dimensional Reynolds-Averaged Navier Stokes analysis with the realizable k–ε model combined with the standard wall function. The variation of the sister holes in the streamwise direction provides similar film cooling performance as the base case for both blowing ratios of 0.5 and 1. On the other hand, the spanwise variation of the sister holes’ location has a more prominent effect on the effectiveness. In some cases, as a result of the anti-vortices generated from the sister holes and the repositioning of the sister holes in the spanwise direction, the jet lift-off effect notably decreases and more volume of coolant is distributed in the spanwise direction.

scholarly journals Choice and Limits of a Fluid Model for the Numerical Study in Dynamic Fluid Structure Interaction Problems

2003 ◽  
Author(s):  
Jean Franc¸ois Sigrist ◽  
Christian Laine ◽  
Dominique Lemoine ◽  
Bernard Peseux
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Model ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Linear Solution ◽  
Fluid Structure ◽  
Design Engineers ◽  
Inviscid Incompressible Fluid ◽  
Basic Fluid

This paper is related to the study of a nuclear propulsion reactor prototype for the French Navy. This prototype is built on ground and is to be dimensioned toward seismic loading. The dynamic analysis takes the coupled fluid structure analysis into account. The basic fluid models used by design engineers are inviscid incompressible or compressible. The fluid can be described in a bidimensional by slice or a three-dimensional approach. A numerical study is carried out on a generic problem for the linear FSI dynamic problem. The results of this study are presented and discussed. As a conclusion, the three-dimensional inviscid incompressible fluid appears to be the best compromise between the description of physical phenomena and the cost of modeling. The geometry of the reactor is such that large displacements of the structure in the fluid can occur. Therefore, the linearity hypothesis might not be longer valid. The case of large amplitude imposed oscillating motion of a cylinder in a confined fluid is numerically studied. A CFD code is used to investigate the fluid behavior solving the NAVIER-STOKES equations. The forces induced on the cylinder by the fluid are computed and compared to the linear solution. The limit of the linear model can then be exhibited.

Large Eddy Simulation of Cross Flow in Pipe Junction

2018 ◽  
Author(s):  
Jiajun Chen ◽  
Yue Sun ◽  
Hang Zhang ◽  
Dakui Feng ◽  
Zhiguo Zhang
Keyword(s):  
Large Eddy Simulation ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Exciting Force ◽  
Navier Stokes ◽  
Pipe Network ◽  
Eddy Simulation ◽  
Large Eddy

Mixing in pipe junctions can play an important role in exciting force and distribution of flow in pipe network. This paper investigated the cross pipe junction and proposed an improved plan, Y-shaped pipe junction. The numerical study of a three-dimensional pipe junction was performed for calculation and improved understanding of flow feature in pipe. The filtered Navier–Stokes equations were used to perform the large-eddy simulation of the unsteady incompressible flow in pipe. From the analysis of these results, it clearly appears that the vortex strength and velocity non-uniformity of centerline, can be reduced by Y-shaped junction. The Y-shaped junction not only has better flow characteristic, but also reduces head loss and exciting force. The results of the three-dimensional improvement analysis of junction can be used in the design of pipe network for industry.

scholarly journals Modeling of Tip Clearance Flows Through an Improved 3-D Pressure Correction Navier-Stokes Solver

1993 ◽  
Author(s):  
N. Lymberopoulos ◽  
K. Giannakoglou ◽  
I. Nikolaou ◽  
K. D. Papailiou ◽  
A. Tourlidakis ◽  
...  
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Special Treatment ◽  
Pressure Correction ◽  
Compressor Rotor ◽  
Numerical Predictions ◽  
Correction Technique

Mechanical constraints dictate the existence of tip clearances in rotating cascades, resulting to a flow leakage through this clearance which considerably influences the efficiency and range of operation of the machine. Three-dimensional Navier-Stokes solvers are often used for the numerical study of compressor and turbine stages with tip-clearance. The quality of numerical predictions depends strongly on how accurately the blade tip region is modelled; in this respect the accurate modelling of tip region was one of the main goals of this work. In the present paper, a 3-D Navier-Stokes solver is suitably adapted so that the flat tip surface of a blade and its sharp edges could be accurately modelled, in order to improve the precision of the calculation in the tip region. The adapted code solves the fully elliptic, steady, Navier-Stokes equations through a space-marching algorithm and a pressure correction technique; the H-type topology is retained, even in cases with thick leading edges where a special treatment is introduced herein. The analysis is applied to two different cases, a linear cascade and a compressor rotor, and comparisons with experimental data are provided.

scholarly journals Modeling the 3-d flow around a cylinder using the SAS hybrid model

2014 ◽  
Vol 16 (5) ◽  
pp. 901-918 ◽  
Keyword(s):  
Turbulence Modeling ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Cross Flow ◽  
Numerical Code ◽  
Navier Stokes ◽  
Computational Domain ◽  
Mean Flow ◽  
Unstable Flow ◽  
Vortex Size

<div> <p>Three-dimensional calculations were performed to simulate the flow around a cylindrical vegetation element using the Scale Adaptive Simulation (SAS) model; commonly, this is the first step of the modeling of the flow through multiple vegetation elements. SAS solves the Reynolds Averaged Navier-Stokes equations in stable flow regions, while in regions with unstable flow it goes unsteady producing a resolved turbulent spectrum after reducing eddy viscosity according to the locally resolved vortex size represented by the von Karman length scale. A finite volume numerical code was used for the spatial discretisation of the rectangular computational domain with stream-wise, cross-flow and vertical dimensions equal to 30D, 11D and 1D, respectively, which was resolved with unstructured grids. Calculations were compared with experiments and Large Eddy Simulations (LES). Predicted overall flow parameters and mean flow velocities exhibited a very satisfactory agreement with experiments and LES, while the agreement of predicted turbulent stresses was satisfactory. Calculations showed that SAS is an efficient and relatively fast turbulence modeling approach, especially in relevant practical problems, in which the very high accuracy that can be achieved by LES at the expense of large computational times is not required.</p> </div> <p>&nbsp;</p>

Sign in / Sign up

Export Citation Format

Share Document