Damage Mechanics of Surface Mount Technology Solder Joints Under Concurrent Thermal and Dynamic Loading

1999 ◽  
Vol 121 (2) ◽  
pp. 61-68 ◽  
Author(s):  
R. Chandaroy ◽  
C. Basaran
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Failure Mode ◽  
Dynamic Loading ◽  
Damage Mechanics ◽  
Solder Joints ◽  
Inelastic Strain ◽  
Simultaneous Application ◽  
Reliability Of Solder Joints

In the electronic industry, the dominant failure mode for solder joints is assumed to be thermal cycling. When semiconductor devices are used in vibrating environment, such as automotive and military applications, dynamic stresses contribute to the failure mechanism of the solder joint, and can become the dominant failure mode. In this paper, a damage mechanics based unified constitutive model for Pb40/Sn60 solder joints has been developed to accurately predict the thermomechanical behavior of solder joints under concurrent thermal and dynamic loading. It is shown that simultaneous application of thermal and dynamic loads significantly shorten the fatigue life. Hence, damage induced in the solder joint by the vibrations have to be included, in fatigue life predictions to correctly predict the reliability of solder joints. The common practice of relating only thermal cycling induced inelastic strain to fatigue life can be inadequate to predict solder joint reliability. A series of parametric studies were conducted to show that contrary to popular opinion all dynamic loading induced strains are not elastic. Hence, vibrations can significantly affect the fatigue life and reliability of solder joints in spite of their small mass.

scholarly journals Prediction of mechanical properties and fatigue life of nano silver paste in chip interconnection

2020 ◽  
Author(s):  
Hui YANG ◽  
Jihui Wu
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Solder Joints ◽  
Stress And Strain ◽  
Nano Silver ◽  
Finite Element Software ◽  
Flip Chips ◽  
Empirical Correction ◽  
Prediction Of Mechanical Properties

Abstract The simulation of nano-silver solder joints in flip-chips is performed by the finite element software ANSYS, and the stress-strain distribution results of the solder joints are displayed. In this simulation, the solder joints use Anand viscoplastic constitutive model, which can reasonably simulate the stress and strain of solder joints under thermal cycling load. At the same time this model has been embedded in ANSYS software, so it is more convenient to use. The final simulation results show that the areas where the maximum stresses and strains occur at the solder joints are mostly distributed in the contact areas between the solder joints and the copper pillars and at the solder joints. During the entire thermal cycling load process, the area where the maximum change in stress and strain occurs is always at the solder joint, and when the temperature changes, the temperature at the solder joint changes significantly. Based on comprehensive analysis, the relevant empirical correction calculation equation is used to calculate and predict the thermal fatigue life of nano-silver solder joints. The analysis results provide a reference for the application of nano-silver solder in the electronic packaging industry.

Reliability of Underfill-Encapsulated Flip-Chips With Heat Spreaders

1998 ◽  
Vol 120 (4) ◽  
pp. 322-327 ◽  
Author(s):  
H. Doi ◽  
K. Kawano ◽  
A. Yasukawa ◽  
T. Sato
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Thermal Cycling ◽  
Failure Mode ◽  
Flip Chip ◽  
Solder Joints ◽  
Alumina Substrate ◽  
Heat Spreader ◽  
Flip Chips ◽  
Heat Spreaders

The effect of a heat spreader on the life of the solder joints for underfill-encapsulated, flip-chip packages is investigated through stress analyses and thermal cycling tests. An underfill with suitable mechanical properties is found to be able to prolong the fatigue life of the solder joints even in a package with a heat spreader and an alumina substrate. The delamination of the underfill from the chip is revealed as another critical failure mode for which the shape of the underfill fillet has a large effect.

Thermomechanical Analysis of Solder Joints Under Thermal and Vibrational Loading

2001 ◽  
Vol 124 (1) ◽  
pp. 60-66 ◽  
Author(s):  
Cemal Basaran ◽  
Rumpa Chandaroy
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Solder Joint ◽  
Constitutive Model ◽  
Solder Joints ◽  
Cycle Fatigue ◽  
Simultaneous Application ◽  
Short Cycle ◽  
Finite Element Procedure ◽  
Life Predictions

Due to the coefficient of thermal expansion (CTE) mismatch between the bonded layers, the solder joint experiences cycling shear strain, which leads to short cycle fatigue. When semiconductor devices are used in a vibrating environment, additional strains shorten the fatigue life of a solder joint. Reliability of these joints in new packages is determined by laboratory tests. In order to use the FEM to replace these expensive reliability tests a unified constitutive model for Pb40/Sn60 solder joints has been developed and implemented in a thermo-viscoplastic-dynamic finite element procedure. The model incorporates thermal-elastic-viscoplastic and damage capabilities in a unified manner. The constitutive model has been verified extensively against laboratory test data. The finite element procedure was used for coupled thermo-viscoplastic-dynamic analyses for fatigue life predictions. The results indicate that using Miner’s rule to calculate accumulative damage by means of two separate analyses, namely dynamic and thermo-mechanical, significantly underestimates the accumulative total damage. It is also shown that a simultaneous application of thermal and dynamic loads significantly shortens the fatigue life of the solder joint. In the microelectronic packaging industry it is common practice to ignore the contribution of vibrations to short cycle fatigue life predictions. The results of this study indicate that damage induced in the solder joints by vibrations have to be included in fatigue life predictions to accurately estimate their reliability.

scholarly journals Prediction of mechanical properties and fatigue life of nano silver paste in chip interconnection

2020 ◽  
Author(s):  
Hui Yang ◽  
Jihui Wu
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Solder Joints ◽  
Stress And Strain ◽  
Nano Silver ◽  
Finite Element Software ◽  
Flip Chips ◽  
Empirical Correction ◽  
Prediction Of Mechanical Properties

Abstract The simulation of nano-silver solder joints in flip-chips is performed by the finite element software ANSYS, and the stress-strain distribution results of the solder joints are displayed. In this simulation, the solder joints use Anand viscoplastic constitutive model, which can reasonably simulate the stress and strain of solder joints under thermal cycling load. At the same time this model has been embedded in ANSYS software, so it is more convenient to use. The final simulation results show that the areas where the maximum stresses and strains occur at the solder joints are mostly distributed in the contact areas between the solder joints and the copper pillars and at the solder joints. During the entire thermal cycling load process, the area where the maximum change in stress and strain occurs is always at the solder joint, and when the temperature changes, the temperature at the solder joint changes significantly. Based on comprehensive analysis, the relevant empirical correction calculation equation is used to calculate and predict the thermal fatigue life of nano-silver solder joints. The analysis results provide a reference for the application of nano-silver solder in the electronic packaging industry.

Strategies for Improving Reliability of Solder Joints on Power Semiconductor Devices

2003 ◽  
Author(s):  
Guo-Quan Lu ◽  
Xingsheng Liu ◽  
Sihua Wen ◽  
Jesus Noel Calata ◽  
John G. Bai
Keyword(s):  
Finite Element ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Flip Chip ◽  
Solder Joints ◽  
Mechanical Stresses ◽  
Flexible Substrates ◽  
Solder Joint Reliability ◽  
Joint Reliability ◽  
Reliability Of Solder Joints

There has been a significant research effort on area-array flip-chip solder joint technology in order to reduce package footprint, enhance current handling capability, and improve heat dissipation. However, there is a lingering concern over cyclic fatigue of solder alloys by thermo-mechanical stresses arising from mismatched thermal expansion coefficients of expansion among the various components of the package. In this paper, some strategies taken to improve the reliability of solder joints on power devices in single-device and multi-chip packages are presented. A strategy for improving solder joint reliability by adjusting solder joint geometry, underfilling and utilization of flexible substrates is discussed with emphasis on triple-stacked solder joints that resemble the shape of an hourglass. The hourglass shape relocates the highest inelastic strain away from the weaker interface with the chip to the bulk region of the joint while the underfill provides a load transfer from the joints. Flexible substrates can deform to relieve thermo-mechanical stresses. Thermal cycling data show significant improvements in reliability when these techniques are used. The design, testing, and finite-element analyses of an interconnection structure, termed the Dimple-Array Interconnect (DAI), for improving the solder joint reliability is also presented. In the DAI structure, a solder is used to join arrays of dimples pre-formed on a metal sheet onto the bonding pads of a device. Finite-element thermo-mechanical analyses and thermal cycling data show that the dimple-array solder joints are more fatigue-resistant than the conventional barrel-shaped solder joints in flip-chip IC packages.

Effect of Stress Gradient on Heat Cycle Fatigue Life Prediction of Solder Joints by Repetitive Bending Test

2021 ◽  
Vol 1016 ◽  
pp. 875-881
Author(s):  
Michiya Matsushima ◽  
Kei Endo ◽  
Tetsuya Kawazoe ◽  
Shinji Fukumoto ◽  
Kozo Fujimoto
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Strain Gradient ◽  
Strain Field ◽  
Thermal Cycle ◽  
Solder Joints ◽  
Inelastic Strain ◽  
Bending Test ◽  
Stress And Strain ◽  
Product Model

Strength of solder joints is usually evaluated by a shear test and a pull test. The reliability of the solder joint is evaluated by the repetitive pull tests of solder bulk specimens. However, the stress and strain field that caused by thermal load on the solder joint of the product model for estimating the reliability is different from these tests. Therefore, we proposed a repetitive bending test as a reliability test of solder joints producing the stress and strain field caused at the solder joint of product model. We proposed a repetitive multi-point bending test as a method to predict the fatigue life of the solder joint in the thermal cycle test in a short period of time. The influence of strain gradient on the inelastic strain amplitude used for lifetime evaluation is estimated. The controllability of the strain gradient by the three-point bending test parameters is investigated. The effect of residual stress on inelastic strain amplitude during sample preparation for thermal cycle test is also evaluated.

A Finite Element Study of Factors Affecting Fatigue Life of Solder Joints

1994 ◽  
Vol 116 (4) ◽  
pp. 265-273 ◽  
Author(s):  
N. Paydar ◽  
Y. Tong ◽  
H. U. Akay
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Solder Joints ◽  
Hold Time ◽  
Strain Range ◽  
Cycle Life ◽  
Finite Element Program ◽  
Factors Affecting

The elastic-plastic-creep characteristics of solder joints are implemented in a nonlinear finite element program ABAQUS by developing user defined material subroutines. An eutectic Pb-Sn solder joint of a resistor carrier under thermal cycling between 125°C and −55°C is modeled, and the effect of various parameters on the solder joint cycle life is evaluated. The strain range of the solder joint under thermal cycling loads is calculated, which is then converted into solder joint cycle life through a fatigue-life relationship proposed by Engelmaier (1983). The parameters studied include: ramp time, hold time, grain size, initial temperature, constitutive equations, material properties for solder alloys, and mesh refinement. The effects of these variations on the fatigue life of solder joints are illustrated. The described method can serve as a tool in the design and manufacturing of surface-mount (SMT) assemblies.

Effects of Ceramic Ball-Grid-Array Package’s Manufacturing Variations on Solder Joint Reliability

1994 ◽  
Vol 116 (4) ◽  
pp. 242-248 ◽  
Author(s):  
Teh-Hua Ju ◽  
Wei Lin ◽  
Y. C. Lee ◽  
Jay J. Liu
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Solder Joints ◽  
Ball Grid Array ◽  
Printed Wiring Board ◽  
Ceramic Ball ◽  
Solder Volume ◽  
Bga Package ◽  
Reliability Of Solder Joints ◽  
Wiring Board

The effects of manufacturing variations on the reliability of solder joints between a ceramic ball grid array (BGA) package and a printed wiring board (PWB) are investigated. Two cases are studied, namely, with and without spacers between the BGA package and the PWB to maintain the solder joint height. Manufacturing variations considered include changes in solder volume, joint height, and pad size. To evaluate the effect of manufacturing variations on reliability, every possible solder joint profile is first derived. The maximum strain is calculated next. Finally, the fatigue life is predicted. The calculations show that these manufacturing variations change the joint profile, and subsequently affect the fatigue life. Since the package is heavy, the use of spacers is necessary to control the solder joint height for reliable connections, and to maintain a large gap for cleaning. The solder joints formed with the use of spacers, may have convex, cylindrical or concave profiles. The concave solder joints are preferred, since they have long fatigue lives and are less sensitive to the manufacturing variations. For the convex solder joints, their fatigue lives are strongly affected by the joint height variation caused by package warpage and by the combined effects of solder volume and pad size.

scholarly journals Prediction of mechanical properties and fatigue life of nano silver paste in chip interconnection

2020 ◽  
Author(s):  
Hui Yang ◽  
Jihui Wu
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Solder Joints ◽  
Stress And Strain ◽  
Nano Silver ◽  
Finite Element Software ◽  
Flip Chips ◽  
Empirical Correction ◽  
Prediction Of Mechanical Properties

Abstract The simulation of nano-silver solder joints in flip-chips is performed by the finite element software ANSYS, and the stress-strain distribution results of the solder joints are displayed. In this simulation, the solder joints use Anand viscoplastic constitutive model, which can reasonably simulate the stress and strain of solder joints under thermal cycling load. At the same time this model has been embedded in ANSYS software, so it is more convenient to use. The final simulation results show that the areas where the maximum stresses and strains occur at the solder joints are mostly distributed in the contact areas between the solder joints and the copper pillars and at the solder joints. During the entire thermal cycling load process, the area where the maximum change in stress and strain occurs is always at the solder joint, and when the temperature changes, the temperature at the solder joint changes significantly. Based on comprehensive analysis, the relevant empirical correction calculation equation is used to calculate and predict the thermal fatigue life of nano-silver solder joints. The analysis results provide a reference for the application of nano-silver solder in the electronic packaging industry.

scholarly journals Microstructure and shear properties of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints under thermal cycling

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jianguo Cui ◽  
Keke Zhang ◽  
Di Zhao ◽  
Yibo Pan
Keyword(s):  
Shear Strength ◽  
Thermal Cycling ◽  
Solder Joints ◽  
High Reliability ◽  
Sharp Decrease ◽  
Thermal Shock Test ◽  
Shear Properties ◽  
Equivalent Time ◽  
Ultrasonic Assisted ◽  
Reliability Of Solder Joints

AbstractThrough ultrasonic wave assisted Sn2.5Ag0.7Cu0.1RExNi/Cu (x = 0, 0.05, 0.1) soldering test and − 40 to 125 °C thermal shock test, the microstructure and shear properties of Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints under thermal cycling were studied by the SEM, EDS and XRD. The results show that the Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints with high quality and high reliability can be obtained by ultrasonic assistance. When the ultrasonic vibration power is 88 W, the ultrasonic-assisted Sn2.5Ag0.7Cu0.1RE0.05Ni/Cu solder joints exhibits the optimized performance. During the thermal cycling process, the shear strength of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints had a linear relationship with the thickness of interfacial intermetallic compound (IMC). Under the thermal cycling, the interfacial IMC layer of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints consisted of (Cu,Ni)6Sn5 and Cu3Sn. The thickness of interfacial IMC of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints was linearly related to the square root of equivalent time. The growth of interfacial IMC of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints had an incubation period, and the growth of IMC was slow within 300 cycles. And after 300 cycles, the IMC grew rapidly, the granular IMC began to merge, and the thickness and roughness of IMC increased obviously, which led to a sharp decrease in the shear strength of the solder joints. The 0.05 wt% Ni could inhibit the excessive growth of IMC, improve the shear strength of solder joints and improve the reliability of solder joints. The fracture mechanism of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints changed from the ductile–brittle mixed fracture in the solder/IMC transition zone to the brittle fracture in the interfacial IMC.

Sign in / Sign up

Export Citation Format

Share Document