Analysis and Design of the “Solar One” Thermal Storage Subsystem Heat Exchangers

1984 ◽  
Vol 106 (3) ◽  
pp. 279-285
Author(s):  
F. R. Weiner
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Thermal Storage ◽  
Design Solution ◽  
Process Conditions ◽  
Analysis And Design ◽  
Heat Exchanger Design ◽  
Central Receiver ◽  
Final Design ◽  
Design Requirements

This paper describes the analysis and design of the five kinds of heat exchangers used in the thermal storage subsystem of the 10 MWe Solar Central Receiver Pilot Plant, now becoming more known as “Solar One.” The paper discusses the practices and standards used in the designs of the heat exchangers, lists the heat exchanger design requirements, and discusses the process conditions. The design assumptions and constraints, the geometrical considerations, and the tradeoff studies that were conducted to optimize the designs are also discussed. A description of each heat exchanger reveals the final design solution. Novel and unique features of a power plant that must operate on a daily sun-cycle are identified.

Optimization and Standardization of Flanged and Flued Expansion Joint Design

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Kamlesh M. Chikhaliya ◽  
Bhaveshkumar P. Patel
Keyword(s):  
Heat Exchanger ◽  
Optimum Design ◽  
Design Methodology ◽  
Thick Wall ◽  
Process Conditions ◽  
Expansion Joint ◽  
Standard Requirement ◽  
Spring Rate ◽  
Tube Heat Exchanger ◽  
Heat Exchanger Design

Flanged and flued type expansion joint (thick wall expansion bellow) used as an integral part of many shell and tube heat exchanger where process conditions produce differential expansion between shell and tubes. It provides flexibility for thermal expansion and also functions as a pressure retaining part. Design of expansion joints is usually based on trial and error method in which initial geometry must be assumed, and accordingly maximum stresses and spring rate are be calculated. Inadequate selection of geometry leads to higher tubesheet and bellow thickness, which increases cost of equipment. This paper presents standardization and optimum design approach of flange and flued expansion bellow fulfilling ASME VIII-1 and TEMA standard requirement. Methodology to define expansion bellow geometry is developed, and geometry dimensions are tabulated for expansion bellow diameter from 300 to 2000 mm and thickness from 6 to 30 mm. Each defined geometry is analyzed using finite element method, and maximum von Mises stresses are calculated for bellow axial displacement from 0.5 to 1.5 mm and internal pressure from 0.1 to 6.5 MPa. Spring rate is also calculated for each defined geometry for consideration in tubesheet calculation. Accordingly, optimum design methodology is developed, tested, and compared with existing design. Results depicted that proposed standardization approach and design methodology will optimize expansion bellow and tubesheet thickness and will also save considerable time in finalization of heat exchanger design.

Basis of the Tubesheet Heat Exchanger Design Rules Used in the French Pressure Vessel Code

1992 ◽  
Vol 114 (1) ◽  
pp. 124-131 ◽  
Author(s):  
F. Osweiller
Keyword(s):  
Heat Exchanger ◽  
Pressure Vessel ◽  
Heat Exchangers ◽  
Tube Bundle ◽  
Outer Edge ◽  
Design Rules ◽  
Effective Elastic Constants ◽  
Heat Exchanger Design ◽  
Solid Plate ◽  
Main Basis

For about 40 years most tubesheet exchangers have been designed according to the standards of TEMA. Partly due to their simplicity, these rules do not assure a safe heat-exchanger design in all cases. This is the main reason why new tubesheet design rules were developed in 1981 in France for the French pressure vessel code CODAP. For fixed tubesheet heat exchangers, the new rules account for the “elastic rotational restraint” of the shell and channel at the outer edge of the tubesheet, as proposed in 1959 by Galletly. For floating-head and U-tube heat exchangers, the approach developed by Gardner in 1969 was selected with some modifications. In both cases, the tubesheet is replaced by an equivalent solid plate with adequate effective elastic constants, and the tube bundle is simulated by an elastic foundation. The elastic restraint at the edge of the tubesheet due the shell and channel is accounted for in different ways in the two types of heat exchangers. The purpose of the paper is to present the main basis of these rules and to compare them to TEMA rules.

A Heuristic for Designing Hybrid Compact Heat Exchangers for Nuclear Applications

2021 ◽  
Author(s):  
Venkata Rajesh Saranam ◽  
Peter Carter ◽  
Kyle Rozman ◽  
Ömer Dogan ◽  
Brian K. Paul
Keyword(s):  
Heat Exchanger ◽  
Diffusion Bonding ◽  
Heat Exchangers ◽  
Nuclear Power ◽  
Nuclear Industry ◽  
Compact Heat Exchangers ◽  
Bonding Parameters ◽  
Heat Exchanger Design ◽  
Creep Fatigue ◽  
Gen Iv

Abstract Hybrid compact heat exchangers (HCHEs) are a potential source of innovation for intermediate heat exchangers in nuclear industry, with HCHEs being designed for Gen-IV nuclear power applications. Compact heat exchangers are commonly fabricated using diffusion bonding, which can provide challenges for HCHEs due to resultant non-uniform stress distributions across hybrid structures during bonding, leading to variations in joint properties that can compromise performance and safety. In this paper, we introduce and evaluate a heuristic for determining whether a feasible set of diffusion bonding conditions exist for producing HCHE designs capable of meeting regulatory requirements under nuclear boiler and pressure vessel codes. A diffusion bonding model for predicting pore elimination and structural analyses are used to inform the heuristic and a heat exchanger design for 316 stainless steel is used to evaluate the efficacy of the heuristic to develop acceptable diffusion bonding parameters. A set of diffusion bonding conditions were identified and validated experimentally by producing various test coupons for evaluating bond strength, ductility, porosity, grain size, creep rupture, creep fatigue and channel deviation. A five-layer hybrid compact heat exchanger structure was fabricated and tensile tested demonstrating that the bonding parameters satisfy all criteria in this paper for diffusion bonding HCHEs with application to the nuclear industry.

Addressing Fouling by Qualifying Chemical Additives Using Novel Technologies

2021 ◽  
Author(s):  
Andrew Robert Farrell ◽  
Dario Marcello Frigo ◽  
Gordon Michael Graham ◽  
Robert Stalker ◽  
Ernesto Ivan Diestre Redondo ◽  
...  
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Emulsion Stability ◽  
Ambient Pressure ◽  
Screening Tests ◽  
Process Conditions ◽  
Screening Methods ◽  
Chemical Additives ◽  
Laboratory Techniques ◽  
Prediction And Prevention

Abstract Fouling of heat exchangers and production of stable emulsions in desalting units can present significant challenges in refinery operations. Often these difficulties occur due to the concurrent processing of two or more crude oils that are incompatible under process conditions. This paper describes a significant development in laboratory techniques for studying these issues and evaluating mitigation strategies. Asphaltenes compatibility was evaluated for oil mixtures that may be co-processed in the refinery using a deposition flow rig, and the results were compared with those obtained with more conventional tests: blending stability analysis by light scattering and various screening methods. The flow rig mimics the process conditions (elevated pressure, high temperature, flow-induced shear) and identifies whether deposition or precipitation will occur. The former can cause fouling of heat exchangers whereas the latter produces solids that can stabilize emulsions in the desalter. By varying the proportions of oils that were co-injected into the deposition flow rig, the range within which mixtures were unstable was found. By flowing through a capillary (to mimic a heat exchanger) and in-line filter, it was possible to identify whether precipitation of suspended flocs or fouling of the heat exchanger itself was the likely issue for each mixture. Emulsion-stability tests were conducted using a pressurized rig with an ersatz separator to mimic the desalting unit; results were compared with those obtained in conventional, ambient-pressure bottle tests. Oil(s) and refinery wash water were injected, mixed under representative shear, and allowed to separate within the typical residence time of the desalter. Chemical additives were tested to identify those that were effective at controlling any observed problems. Results obtained in either flow rig (using representative pressure, temperature, and shear) did not always match those obtained using conventional methods. Asphaltenes fouling occurred under conditions where it was not predicted by screening tests that were conducted at conditions not representative of the process and did not occur under conditions where it was predicted. Differences were also observed between the emulsion stability observed in bottle versus rig tests, though these should be viewed as complementary techniques. This paper presents new laboratory techniques for the prediction and prevention of refinery fouling and emulsion stability. They mimic conditions in the facilities much better than those typically used to date.

Earth-Air and Earth-Water Heat Exchanger Design for Ventilation Systems in Buildings

2010 ◽  
Author(s):  
Michel De Paepe ◽  
Christophe T’Joen ◽  
Arnold Janssens ◽  
Marijke Steeman
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Design Methodology ◽  
Energy Use ◽  
Polyethylene Tube ◽  
Dynamic Simulations ◽  
Tube Heat Exchanger ◽  
Heat Exchanger Design ◽  
The Earth ◽  
Software Codes

Earth-air heat exchangers are often used for (pre)heating or (pre)cooling of ventilation air in low energy or passive house standard buildings. Several studies have been published in the passed about the performance of these earth-air heat exchangers [1–8]. Often this is done in relation to the building energy use. Several software codes are available with which the behaviour of the earth-air heat exchanger can be simulated. De Paepe and Janssens published a simplified design methodology for earth-air heat exchangers, based on thermal to hydraulic performance optimisation [7]. Through dynamic simulations and measurements it was shown that the methodology is quite conservative [9–10]. Hollmu¨ller added an earth-air heat exchanger model to TRNSYS [11]. In stead of using earth-air heat exchangers, earth-water heat exchangers are now getting more attention. In this system the ventilation air is indirectly cooled/heated with the water flow in a fin-tube heat exchanger in the inlet of the ventilation channel. The water-glycol mixture transfers heat with the earth by flowing through e.g. a polyethylene tube. In the second part of this paper a design methodology is first derived and then applied to this type of system.

A Numerical Algorithm and a Graphical Method to Size a Heat Exchanger

2011 ◽  
Author(s):  
Torsten Berning
Keyword(s):  
Heat Exchanger ◽  
Numerical Algorithm ◽  
Heat Exchangers ◽  
Graphical Method ◽  
Application Software ◽  
Microsoft Excel ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient ◽  
Heat Exchanger Design ◽  
Shell And Tube

This paper describes the development of a numerical algorithm and a graphical method that can be employed in order to determine the overall heat transfer coefficient inside heat exchangers. The method is based on an energy balance and utilizes the spreadsheet application software Microsoft Excel™. The application is demonstrated in an example for designing a single pass shell and tube heat exchanger that was developed in the Department of Materials Technology of the Norwegian University of Science and Technology (NTNU) where water vapor is superheated by a secondary oil cycle. This approach can be used to reduce the number of hardware iterations in heat exchanger design.

scholarly journals Plate heat exchanger design software for industrial and educational applications

2017 ◽  
Vol 71 (5) ◽  
pp. 439-449
Author(s):  
Nikola Zlatkovic ◽  
Divna Majstorovic ◽  
Mirjana Kijevcanin ◽  
Emila Zivkovic
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Plate Heat Exchanger ◽  
Heat Transfer Area ◽  
Transfer Coefficients ◽  
Plate Heat ◽  
Two Fluids ◽  
Heat Exchanger Design ◽  
Educational Applications

Plate heat exchanger is a type of heat exchanger that uses corrugated metal plates to transfer heat between two fluids. The plate corrugations are designed to achieve turbulence across the entire heat transfer area thus producing the highest possible heat transfer coefficients while allowing close temperature approaches. Subsequently, this leads to a smaller heat transfer area, smaller units and in some cases, fewer heat exchangers. In this work, an application for thermal and hydraulic computations of plate heat exchangers had been developed using Sharp Develop, an open source programming platform. During the development process, several literature methods and correlations for calculation of heat transfer coefficient and pressure drop in a plate heat exchanger have been tested and the selected four methods: Martin, VDI, Kumar and Coulson and Richardson have been incorporated into the software. The structure of the software is visually presented through several windows: a window for inserting input data, windows for showing the results of computation by each of the methods, a window for showing comparative analysis of the most important computation results obtained by all of the used methods and a help window for demonstrating the working principle of plate heat exchanger.

scholarly journals Study on Shell-and-Tube Heat Exchanger Models with Different Degree of Complexity for Process Simulation and Control Design

2018 ◽  
Author(s):  
Javier Bonilla
Keyword(s):  
Heat Exchanger ◽  
Molten Salt ◽  
Heat Exchangers ◽  
Control Strategies ◽  
Thermal Storage ◽  
Working Fluid ◽  
Tube Heat Exchanger ◽  
Test Loop ◽  
Shell And Tube ◽  
Thermal Oil

Many commercial solar thermal power plants rely on indirect thermal storage systems in order to provide a stable and reliable power supply, where the working fluid is commonly thermal oil and the storage fluid is molten salt. The thermal oil - molten salt heat exchanger control strategies, to charge and discharge the thermal storage system, strongly affect the performance of the whole plant. Shell-and-tube heat exchangers are the most common type of heat exchangers used in these facilities. With the aim of developing advanced control strategies accurate and fast dynamic models of shell-and-tube heat exchangers are essential. For this reason, several shell-and-tube heat exchanger models with different degrees of complexity have been studied, analyzed and validated against experimental data from the CIEMAT-PSA molten salt test loop for thermal energy systems facility. Simulation results are compared in steady-state as well as transient predictions in order to determine the required complexity of the model to yield accurate results.

scholarly journals Heat exchanger design studies for molten salt fast reactor

2019 ◽  
Vol 5 ◽  
pp. 12
Author(s):  
Uğur Köse ◽  
Ufuk Koç ◽  
Latife Berrin Erbay ◽  
Erdem Öğüt ◽  
Hüseyin Ayhan
Keyword(s):  
Heat Exchanger ◽  
Molten Salt ◽  
Fast Reactor ◽  
Heat Exchangers ◽  
Temperature Drop ◽  
Freezing Temperature ◽  
Fuel Temperature ◽  
Design Studies ◽  
The Core ◽  
Heat Exchanger Design

In this study, conceptual design for primary heat exchanger of the Molten Salt Fast Reactor is made. The design was carried out to remove the produced heat from the reactor developed under the SAMOFAR project. Nominal power of the reactor is 3 GWth and it has 16 heat exchangers. There are several requirements related to the heat exchanger. To sustain the steady-state conditions, heat exchangers have to transfer the heat produced in the core and it has to maintain the temperature drop as much as the temperature rise in the core due to the fission. It should do it as fast as possible. It must also ensure that the fuel temperature does not reach the freezing temperature to avoid solidification. In doing so, the fuel volume in the heat exchanger must not exceed the specified limit. Design studies were carried out taking into account all requirements and final geometric configurations were determined. Plate type heat exchanger was adopted in this study. 3D CFD analyses were performed to investigate the thermal-hydraulic behavior of the system. Analyses were made by ANSYS-Fluent commercial code. Results are in a good agreement with limitations and requirements specified for the reactor designed under the SAMOFAR project.

scholarly journals Optimization of a New Design of Molten Salt-to-CO2 Heat Exchanger Using Exergy Destruction Minimization

Entropy ◽  
2020 ◽  
Vol 22 (8) ◽  
pp. 883
Author(s):  
María José Montes ◽  
José Ignacio Linares ◽  
Rubén Barbero ◽  
Beatriz Yolanda Moratilla
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Molten Salt ◽  
High Heat ◽  
Exergy Destruction ◽  
Solar Thermal Energy ◽  
Heat Exchanger Design ◽  
Central Receiver ◽  
High Heat Transfer ◽  
Supercritical Phase

One of the ways to make cost-competitive electricity, from concentrated solar thermal energy, is increasing the thermoelectric conversion efficiency. To achieve this objective, the most promising scheme is a molten salt central receiver, coupled to a supercritical carbon dioxide cycle. A key element to be developed in this scheme is the molten salt-to-CO2 heat exchanger. This paper presents a heat exchanger design that avoids the molten salt plugging and the mechanical stress due to the high pressure of the CO2, while improving the heat transfer of the supercritical phase, due to its compactness with a high heat transfer area. This design is based on a honeycomb-like configuration, in which a thermal unit consists of a circular channel for the molten salt surrounded by six smaller trapezoidal ducts for the CO2. Further, an optimization based on the exergy destruction minimization has been accomplished, obtained the best working conditions of this heat exchanger: a temperature approach of 50 °C between both streams and a CO2 pressure drop of 2.7 bar.

Sign in / Sign up

Export Citation Format

Share Document