Design of a Plane-Type Bidirectional Thermal Diode

1988 ◽  
Vol 110 (4) ◽  
pp. 299-305 ◽  
Author(s):  
K. Chen
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Transfer Rate ◽  
Reverse Bias ◽  
Energy Utilization ◽  
Heat Transfer Analysis ◽  
Transfer Rates ◽  
One Dimensional ◽  
Plane Type ◽  
Solar Energy Utilization

The design of a plane-type, bidirectional thermal diode is presented. This diode is composed of two vertical plates and several fluid-filled loops with their horizontal segments soldered to the vertical plates. This invention is simple in construction and low in cost. The direction of heat transfer in the invented thermal diode can be easily reversed. These features of the present invention make it very attractive to solar energy utilization. Natural convection analysis for thermosyphon operations was adopted for heat transfer calculations of the fluid-filled loops. A one-dimensional heat transfer analysis was employed to estimate the heat transfer rate and ratio of heat transfer rates of the diode under forward and reverse bias.

Heat Transfer by Natural Convection of Helium Between Horizontal Isothermal Concentric Cylinders at Cryogenic Temperature

1988 ◽  
Vol 110 (1) ◽  
pp. 109-115 ◽  
Author(s):  
E. H. Bishop
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Transfer Rate ◽  
Correlation Equation ◽  
Diameter Ratio ◽  
Temperature Profiles ◽  
Cryogenic Temperatures ◽  
Transfer Rates ◽  
Concentric Cylinders

An experimental study was performed of the heat transfer by natural convection of helium between horizontal isothermal concentric cylinders at cryogenic temperatures. Time-averaged temperature profiles at various locations in the annulus and overall heat transfer rates were measured as the Rayleigh number was varied from 6 × 106 to 2 × 109 and the expansion number from 0.20 to 1.0 for a constant Prandtl number of 0.688 and diameter ratio of 3.36. It was found that the heat transfer rate depends on the magnitude of the expansion number as well as on the magnitude of the Rayleigh number. With gas properties evaluated at a volume-weighted reference temperature, a correlation equation is presented that correlates the heat transfer data with maximum deviations of −8.2 and +8.5 percent. The results of this study are compared with previously published studies of other investigators.

scholarly journals Heat Transfer Analysis of Viscous Incompressible Fluid by Combined Natural Convection and Radiation in an Open Cavity

2014 ◽  
Vol 2014 ◽  
pp. 1-14 ◽  
Author(s):  
M. Saleem ◽  
M. A. Hossain ◽  
Suvash C. Saha ◽  
Y. T. Gu
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Optical Thickness ◽  
Radiative Heat Transfer ◽  
Transfer Rate ◽  
Radiative Heat ◽  
Radiation Heat Transfer ◽  
Open Cavity ◽  
Heat Transfer Analysis

The effect of radiation on natural convection of Newtonian fluid contained in an open cavity is investigated in this study. The governing partial differential equations are solved numerically using the Alternate Direct Implicit method together with the Successive Overrelaxation method. The study is focused on studying the flow pattern and the convective and radiative heat transfer rates are studied for different values of radiation parameters, namely, the optical thickness of the fluid, scattering albedo, and the Planck number. It was found that, in the optically thin limit, an increase in the optical thickness of the fluid raises the temperature and radiation heat transfer of the fluid. However, a further increase in the optical thickness decreases the radiative heat transfer rate due to increase in the energy level of the fluid, which ultimately reduces the total heat transfer rate within the fluid.

scholarly journals One-dimensional particle models for heat transfer analysis

2010 ◽  
Vol 260 ◽  
pp. 012005 ◽  
Author(s):  
H Bufferand ◽  
G Ciraolo ◽  
Ph Ghendrih ◽  
P Tamain ◽  
F Bagnoli ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Analysis ◽  
One Dimensional

Three-Dimensional Natural Convection From Vertical Heated Plates With Adjoining Cool Surfaces

1992 ◽  
Vol 114 (1) ◽  
pp. 115-120 ◽  
Author(s):  
B. W. Webb ◽  
T. L. Bergman
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Control Volume ◽  
Three Dimensional ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Uniform Heat Flux ◽  
Infrared Thermal Imaging ◽  
Transfer Rates ◽  
Thermal Boundary Conditions

Natural convection in an enclosure with a uniform heat flux on two vertical surfaces and constant temperature at the adjoining walls has been investigated both experimentally and theoretically. The thermal boundary conditions and enclosure geometry render the buoyancy-induced flow and heat transfer inherently three dimensional. The experimental measurements include temperature distributions of the isoflux walls obtained using an infrared thermal imaging technique, while the three-dimensional equations governing conservation of mass, momentum, and energy were solved using a control volume-based finite difference scheme. Measurements and predictions are in good agreement and the model predictions reveal strongly three-dimensional flow in the enclosure, as well as high local heat transfer rates at the edges of the isoflux wall. Predicted average heat transfer rates were correlated over a range of the relevant dimensionless parameters.

scholarly journals A RANS K-? SIMULATION OF 2D TURBULENT NATURAL CONVECTION IN AN ENCLOSURE WITH HEATING SOURCES

2019 ◽  
Vol 20 (1) ◽  
pp. 229-244
Author(s):  
Mehdi Ahmadi ◽  
Seyed Ali Agha Mirjalily ◽  
Seyed Amir Abbas Oloomi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Kinetic Energy ◽  
Aspect Ratio ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Turbulent Natural Convection ◽  
Cold Source ◽  
Thermal Sources

ABSTRACT: This study is conducted to investigate turbulent natural convection flow in an enclosure with thermal sources using the low-Reynolds number (LRN) k-? model. This enclosure has a cold source with temperature Tc and a hot source with temperature Th as thermal sources, other walls of the enclosure are adiabatic. The aim of this study is to predict the effect of change in Rayleigh number, repositioning of cold and hot sources, and thermal sources aspect ratio on the flow field, temperature, and rate of heat transfer. To achieve this aim, the equations of continuity, momentum, energy, turbulent kinetic energy, and kinetic energy dissipation are employed in the case of 2D turbulence with constant thermo-physical properties except the density in the buoyancy term (Boussinesq approximation). To numerically solve these equations, the finite volume method and SIMPLE algorithm are used. According to the modeling results, the most optimal temperature distribution in the enclosure is seen when the hot source is below the cold source. With decreasing distance between hot and cold sources, heat transfer rate increases. The maximal heat transfer rate is derived via study of the heating sources aspect ratio. In constant positions of cold and hot sources on a wall, the heat transfer rate increases with increasing Rayleigh number (Ra=109-1011). ABSTAK: Kajian ini dijalankan bagi mengkaji perubahan semula jadi aliran perolakan dalam tempat tertutup dengan sumber haba menggunakan model k-? nombor Reynolds-rendah (LRN). Bekas tertutup ini mempunyai dua sumber haba iaitu sumber sejuk dengan suhu Tc dan sumber panas dengan suhu Th, manakala dinding lain bekas ini adalah adiabatik. Tujuan kajian ini adalah bagi mengesan perubahan nombor Rayleigh, mengubah sumber sejuk dan panas dan nisbah sumber haba kepada kawasan aliran, suhu dan halaju perubahan haba. Bagi mencapai tujuan tersebut, persamaan sambungan, momentum, tenaga, tenaga kinetik perolakan, dan pengurangan tenaga kinetik telah dilaksanakan dalam kes perolakan 2D dengan sifat fizikal-haba berterusan (malar) kecuali isipadu terma keapungan (anggaran Boussinesq). Bagi menyelesaikan persamaan ini secara berangka, kaedah isipadu terhad dan algorithma MUDAH telah digunakan. Berdasarkan keputusan model, suhu distribusi optimal dalam bekas tertutup dilihat apabila sumber panas adalah kurang daripada sumber sejuk. Dengan pengurangan jarak antara sumber panas dan sejuk, kadar pertukaran haba meningkat. Kadar pertukaran haba maksima telah diperoleh melalui kajian nisbah  aspek sumber pemanasan. Kadar pertukaran haba bertambah dengan bertambahnya nombor Rayleigh  (Ra=109-1011), pada posisi tetap sumber sejuk dan panas pada dinding bekas.

scholarly journals Numerical heat transfer analysis of micro-scale jet-impingement cooling in a high-pressure turbine vane

2021 ◽  
Author(s):  
Karan Anand
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Heat Transfer Analysis ◽  
Transfer Rates ◽  
Numerical Heat Transfer ◽  
Turbine Vane ◽  
Single Jet

This research provides a computational analysis of heat transfer due to micro jet-impingement inside a gas turbine vane. A preliminary-parametric analysis of axisymmetric single jet was reported to better understand micro jet-impingement. In general, it was seen that as the Reynolds number increased the Nusselt number values increased. The jet to target spacing had a considerably lower impact on the heat transfer rates. Around 30% improvement was seen by reducing the diameter to half while changing the shape to an ellipse saw 20.8% improvement in Nusselt value. The numerical investigation was then followed by studying the heat transfer characteristics in a three-dimensional, actual-shaped turbine vane. Effects of jet inclination showed enhanced mixing and secondary heat transfer peaks. The effect of reducing the diameter of the jets to 0.125 mm yielded 55% heat transfer improvements compared to 0.51 mm; the tapering effect also enhanced the local heat transfer values as local velocities at jet exit increased.

An Analytical Study of Heat Transfer in Finite Tissue With Two Blood Vessels and Uniform Dirichlet Boundary Conditions

2005 ◽  
Vol 127 (2) ◽  
pp. 179-188 ◽  
Author(s):  
Devashish Shrivastava ◽  
Benjamin McKay ◽  
Robert B. Roemer
Keyword(s):  
Heat Transfer ◽  
Boundary Conditions ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Source Term ◽  
Dirichlet Boundary ◽  
Total Heat ◽  
Dirichlet Boundary Conditions ◽  
Total Heat Transfer ◽  
Transfer Rates

Counter-current (vessel–vessel) heat transfer has been postulated as one of the most important heat transfer mechanisms in living systems. Surprisingly, however, the accurate quantification of the vessel–vessel, and vessel–tissue, heat transfer rates has never been performed in the most general and important case of a finite, unheated/heated tissue domain with noninsulated boundary conditions. To quantify these heat transfer rates, an exact analytical expression for the temperature field is derived by solving the 2-D Poisson equation with uniform Dirichlet boundary conditions. The new results obtained using this solution are as follows: first, the vessel–vessel heat transfer rate can be a large fraction of the total heat transfer rate of each vessel, thus quantitatively demonstrating the need to accurately model the vessel–vessel heat transfer for vessels imbedded in tissues. Second, the vessel–vessel heat transfer rate is shown to be independent of the source term; while the heat transfer rates from the vessels to the tissue show a significant dependence on the source term. Third, while many previous studies have assumed that (1) the total heat transfer rate from vessels to tissue is zero, and/or (2) the heat transfer rates from paired vessels (of different sizes and at different temperatures) to tissue are equal to each other the current analysis shows that neither of these conditions is met. The analytical solution approach used to solve this two vessels problem is general and can be extended for the case of “N” arbitrarily located vessels.

Natural Convection in an Anisotropic Porous Enclosure Due to Nonuniform Heating From the Bottom Wall

2009 ◽  
Vol 131 (7) ◽  
Author(s):  
Ashok Kumar ◽  
P. Bera
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Principal Direction ◽  
Orientation Angle ◽  
Bottom Wall ◽  
Nonuniform Heating ◽  
Material Derivative ◽  
Porous Enclosure

A comprehensive numerical investigation on the natural convection in a hydrodynamically anisotropic porous enclosure is presented. The flow is due to nonuniformly heated bottom wall and maintenance of constant temperature at cold vertical walls along with adiabatic top wall. Brinkman-extended non-Darcy model, including material derivative, is considered. The principal direction of the permeability tensor has been taken oblique to the gravity vector. The spectral element method has been adopted to solve numerically the governing conservative equations of mass, momentum, and energy by using a stream-function vorticity formulation. Special attention is given to understand the effect of anisotropic parameters on the heat transfer rate as well as flow configurations. The numerical experiments show that in the case of isotropic porous enclosure, the maximum rates of bottom as well as side heat transfers (Nub and Nus) take place at the aspect ratio, A, of the enclosure equal to 1, which is, in general, not true in the case of anisotropic porous enclosures. The flow in the enclosure is governed by two different types of convective cells: rotating (i) clockwise and (ii) anticlockwise. Based on the value of media permeability as well as orientation angle, in the anisotropic case, one of the cells will dominate the other. In contrast to isotropic porous media, enhancement of flow convection in the anisotropic porous enclosure does not mean increasing the side heat transfer rate always. Furthermore, the results show that anisotropy causes significant changes in the bottom as well as side average Nusselt numbers. In particular, the present analysis shows that permeability orientation angle has a significant effect on the flow dynamics and temperature profile and consequently on the heat transfer rates.

Effect of a Magnetic Field on the Heat Transfer Rate on Free Convection in a Rectangular Cavity

2005 ◽  
Author(s):  
Gustavo Gutierrez ◽  
Ezequiel Medici
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Stokes Equations ◽  
Rectangular Cavity ◽  
Convection Flow ◽  
Interesting Phenomenon ◽  
The Magnetic Field

The interaction between magnetic fields and convection is an interesting phenomenon because of its many important engineering applications. Due to natural convection motion the electric conductive fluid in a magnetic field experiences a Lorenz force and its effect is usually to reduce the flow velocities. A magnetic field can be used to control the flow field and increase or reduce the heat transfer rate. In this paper, the effect of a magnetic field in a natural convection flow of an electrically conducting fluid in a rectangular cavity is studied numerically. The two side walls of the cavity are maintained at two different constant temperatures while the upper wall and the lower wall are completely insulated. The coupling of the Navier-Stokes equations with the Maxwell equations is discussed with the assumptions and main simplifications assumed in typical problems of magnetohydrodynamics. The nonlinear Lorenz force generates a rich variety of flow patterns depending on the values of the Grashof and Hartmann numbers. Numerical simulations are carried out for different Grashof and Hartmann numbers. The effect of the magnetic field on the Nusselt number is discussed as well as how convection can be suppressed for certain values of the Hartmann number under appropriate direction of the magnetic field.

Sign in / Sign up

Export Citation Format

Share Document