Oscillating Heat Transfer Correlations for Spiral-Coil Thermoacoustic Heat Exchangers

2015 ◽  
Vol 7 (3) ◽  
Author(s):  
Kriengkrai Assawamartbunlue ◽  
Channarong Wantha
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Transfer Coefficients ◽  
Spiral Coil ◽  
Heat Transfer Coefficients ◽  
Flow Heat ◽  
Heat Transfer Correlations ◽  
Coil Heat Exchanger ◽  
Coil Heat

Heat exchangers are the important parts in thermoacoustic refrigerators. Types and configurations of the heat exchangers affect flow behaviors through stacks, and heat transfer behaviors between working fluids and the heat exchangers. Steady-flow heat transfer correlations to design a heat exchanger are not suitable for the thermoacoustic refrigerators due to their oscillatory flow conditions in resonator tubes. In this paper, a heat transfer correlation for a spiral-coil heat exchanger is presented. The results from the experimental study were used to develop an empirical equation between the Colburn-j factor, the Prandtl number, and the Reynolds number to correlate the oscillating heat transfer coefficient at the spiral-coil heat exchangers. The results showed that using steady-flow heat transfer correlations for analyses and design of the heat exchanger could result in distinguished errors. The heat transfer correlations developed for oscillatory flows on fin heat exchangers are also not suitable to predict heat transfer coefficients for spiral-coil heat exchanger due to difference in flow behaviors on the heat transfer surface. For oscillatory flows, the heat transfer coefficients can be improved by using curved-liked surface such as spiral coil instead of straightlike surface such as fin coil. The relationships between the oscillating heat transfer coefficients at the heat exchangers, drive ratios, and operating frequencies are also presented. Higher drive ratios and operating frequency result in greater heat transfer coefficients.

scholarly journals Evaluation of selected methods of the heat transfer coefficient determination in fin-and-tube cross-flow heat exchangers

2018 ◽  
Vol 240 ◽  
pp. 02004 ◽  
Author(s):  
Tomasz Bury ◽  
Małgorzata Hanuszkiewicz Drapała
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Flow Heat ◽  
The Heat Transfer Coefficient

The work is a part of a thermodynamic analysis of a finned cross-flow heat exchanger of the liquid-gas type. The heat transfer coefficients on the liquid and the gas side and the area of the heat transfer are the main parameters describing such a device. The basic problem in computations of such heat exchangers is determination of the coefficient of the heat transfer from the finned surfaces to the gas. The differences in the heat transfer coefficient local values resulting from the non-uniform flow of mediums through the exchanger complicates the analysis additionally. Six Nusselt number relationships are selected as suitable for the considered heat exchanger, and they are used to calculate the heat transfer coefficient for the air temperature ranging from 10°C to 30°C and for the velocity values ranging from 2 m/s to 20 m/s. In the next step, the gas-side heat transfer coefficient is determined by means of numerical simulations using a numerical model of a repetitive fragment of the heat exchanger under consideration. Finally, the Wilson plot method is also used. The work focuses on an analysis of the in-house HEWES code sensitivity to the method of the heat transfer coefficient determination. The authors believe that the analysis may also be useful for the evaluation of different methods of the heat transfer coefficient computation.

A Variable-Curvature Spiral-Coil Heat Exchanger for Automobile Exhaust Heat Recovery

2019 ◽  
Vol 12 (3) ◽  
Author(s):  
Yu Zhu ◽  
Fengye Yang ◽  
Yueguang Guo
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Recovery ◽  
Heat Transfer Performance ◽  
Cone Angle ◽  
Spiral Coil ◽  
Variable Curvature ◽  
Exhaust Heat ◽  
Coil Heat Exchanger ◽  
Coil Heat

Abstract To improve the fuel efficiency of automobile engines and reduce pollution owing to automobile exhaust, this study discusses a fixed-curvature spiral-coil heat exchanger that recovers exhaust heat. Herein, the heat transfer performance of the spiral coil is studied via experimental testing and numerical simulation. In this study, a new type of variable-curvature spiral coil is designed to improve the efficiency of the heat exchanger. The effect of different conical angles on the resistance and heat transfer performance of the spiral coil within a range of Reynolds numbers of 4000–14,000 was analyzed. The heat exchange efficiency is a combination of the convective heat transfer and the overall heat recovery. The results of this study indicate that for a spiral-coil tube of length L, increasing the cone angle improves the convective heat transfer outside the tube. However, as the flow resistance increases, the exhaust heat recovery of a variable-curvature spiral-coil heat exchanger (VSE) is up to 18.8% higher than that of a constant curvature spiral-coil heat exchanger. The combined performance of VSE is excellent when the cone angle is 15 deg.

Experimental Investigation of Coil Curvature Effect on Heat Transfer and Pressure Drop Characteristics of Shell and Coil Heat Exchanger

2014 ◽  
Vol 7 (1) ◽  
Author(s):  
M. R. Salem ◽  
K. M. Elshazly ◽  
R. Y. Sakr ◽  
R. K. Ali
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Average Nusselt Number ◽  
Transfer Coefficients ◽  
Nusselt Numbers ◽  
Fanning Friction Factor ◽  
Coil Heat

The present work experimentally investigates the characteristics of convective heat transfer in horizontal shell and coil heat exchangers in addition to friction factor for fully developed flow through the helically coiled tube (HCT). The majority of previous studies were performed on HCTs with isothermal and isoflux boundary conditions or shell and coil heat exchangers with small ranges of HCT configurations and fluid operating conditions. Here, five heat exchangers of counter-flow configuration were constructed with different HCT-curvature ratios (δ) and tested at different mass flow rates and inlet temperatures of the two sides of the heat exchangers. Totally, 295 test runs were performed from which the HCT-side and shell-side heat transfer coefficients were calculated. Results showed that the average Nusselt numbers of the two sides of the heat exchangers and the overall heat transfer coefficients increased by increasing coil curvature ratio. The average increase in the average Nusselt number is of 160.3–80.6% for the HCT side and of 224.3–92.6% for the shell side when δ increases from 0.0392 to 0.1194 within the investigated ranges of different parameters. Also, for the same flow rate in both heat exchanger sides, the effect of coil pitch and number of turns with the same coil torsion and tube length is remarkable on shell average Nusselt number while it is insignificant on HCT-average Nusselt number. In addition, a significant increase of 33.2–7.7% is obtained in the HCT-Fanning friction factor (fc) when δ increases from 0.0392 to 0.1194. Correlations for the average Nusselt numbers for both heat exchanger sides and the HCT Fanning friction factor as a function of the investigated parameters are obtained.

scholarly journals Experimental determination of correlations for mean heat transfer coefficients in plate fin and tube heat exchangers

2012 ◽  
Vol 33 (3) ◽  
pp. 1-24 ◽  
Author(s):  
Dawid Taler
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Correlation Coefficients ◽  
Outlet Temperature ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nonlinear Regression Method ◽  
Propagation Rule

Abstract This paper presents a numerical method for determining heat transfer coefficients in cross-flow heat exchangers with extended heat exchange surfaces. Coefficients in the correlations defining heat transfer on the liquid- and air-side were determined using a nonlinear regression method. Correlation coefficients were determined from the condition that the sum of squared liquid and air temperature differences at the heat exchanger outlet, obtained by measurements and those calculated, achieved minimum. Minimum of the sum of the squares was found using the Levenberg-Marquardt method. The uncertainty in estimated parameters was determined using the error propagation rule by Gauss. The outlet temperature of the liquid and air leaving the heat exchanger was calculated using the analytical model of the heat exchanger.

The Correlation of Heat Transfer Coefficients for the Laminar Natural Convection in a Circular Finned-Tube Heat Exchanger

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Hie Chan Kang ◽  
Se-Myong Chang
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Nusselt Number ◽  
Natural Convection ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Finned Tube ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Laminar Natural Convection

This study proposes an empirical correlation for laminar natural convection applicable to external circular finned-tube heat exchangers with wide range of configuration parameters. The transient temperature response of the heat exchangers was used to obtain the heat transfer coefficient, and the experimental data with their characteristic lengths are discussed. The data lie in the range from 1 to 1000 for Rayleigh numbers based on the fin spacing: the ratio of fin height to tube diameter ranges from 0.1 to 0.9, and the ratio of fin pitch to height ranges from 0.13 to 2.6. Sixteen sets of finned-tube electroplated with nickel–chrome were tested. The convective heat transfer coefficients on the heat exchangers were measured by elimination of the thermal radiation effect from the heat exchanger surfaces. The Nusselt number was correlated with a newly suggested composite curve formula, which converges to the quarter power of the Rayleigh number for a single cylinder case. The proposed characteristic length for the Rayleigh number is the fin pitch while that for the Nusselt number is mean flow length, defined as half the perimeter of the mean radial position inside the flow region bounded by the tube surface and two adjacent fins. The flow is regarded as laminar, which covers heat exchangers from a single horizontal cylinder to infinite parallel disks. Consequently, the result of curve fitting for the experimental data shows the reasonable physical interpretation as well as the good quantitative agreement with the correction factors.

Experimental Study and Genetic-Algorithm-Based Correlation on Shell-Side Heat Transfer and Flow Performance of Three Different Types of Shell-and-Tube Heat Exchangers

2006 ◽  
Vol 129 (9) ◽  
pp. 1277-1285 ◽  
Author(s):  
Qiu-wang Wang ◽  
Gong-nan Xie ◽  
Bo-tao Peng ◽  
Min Zeng
Keyword(s):  
Heat Transfer ◽  
Genetic Algorithm ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Transfer Coefficients ◽  
Shell Side ◽  
Heat Transfer Coefficients ◽  
Friction Factors ◽  
Shell And Tube

The heat transfer and pressure drop of three types of shell-and-tube heat exchangers, one with conventional segmental baffles and the other two with continuous helical baffles, were experimentally measured with water flowing in the tube side and oil flowing in the shell side. The genetic algorithm has been used to determine the coefficients of correlations. It is shown that under the identical mass flow, a heat exchanger with continuous helical baffles offers higher heat transfer coefficients and pressure drop than that of a heat exchanger with segmental baffles, while the shell structure of the side-in-side-out model offers better performance than that of the middle-in-middle-out model. The predicted heat transfer rates and friction factors by means of the genetic algorithm provide a closer fit to experimental data than those determined by regression analysis. The predicted corrections of heat transfer and flow performance in the shell sides may be used in engineering applications and comprehensive study. It is recommended that the genetic algorithm can be used to handle more complicated problems and to obtain the optimal correlations.

Coil Heat Exchanger with the Nanofluid Filled Buffer Layer

2016 ◽  
Vol 831 ◽  
pp. 223-231 ◽  
Author(s):  
Robert Smusz ◽  
Joanna Wilk
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Buffer Layer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Waste Heat ◽  
Thermal Power ◽  
Transfer Coefficients ◽  
Coil Heat Exchanger ◽  
Coil Heat

The paper presents the preliminary design of the special heat exchanger. The device under consideration is the kind of immersed coil heat exchangers. It consists of three vertical coils: two coils are standard, water is used as a heating medium; one coil is filled by the refrigerant R134a which transfers the waste heat from refrigeration and air conditioning system during the boiling processes. In order to prevent the possible refrigerant leakage, the special buffer layer filled with the nanofluid is mounted in the Freon coil. Thermophysical properties of the nanofluid cause the intensification of the heat transfer through the buffer layer and the same increase of the heat transfer rate. Calculations of thermal power were made. Correlations of heat transfer coefficients in curved tubes, pressure drop correlations for flow through helical coil tubes and correlations describing the heat transfer in the buffer layer, were applied. Results of the calculations indicate of the influence of of Freon coil on the exchanger heat transfer rate. Heat power of Freon coil is about 7 – 25% of water coil thermal power. Thus, the waste heat applied significantly increases the exchanger heat transfer rate.

scholarly journals Numerical and experimental investigation of heat transfer of ZnO/Water nanofluid in the concentric tube and plate heat exchangers

2011 ◽  
Vol 15 (1) ◽  
pp. 183-194 ◽  
Author(s):  
Fard Haghshenas ◽  
Mohammad Talaie ◽  
Somaye Nasr
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Transfer Rate ◽  
Heat Exchangers ◽  
Transfer Rate ◽  
Transfer Coefficients ◽  
Flow Rates ◽  
Plate Heat ◽  
Heat Transfer Coefficients ◽  
Mass Flow Rates

The plate and concentric tube heat exchangers are tested by using the water-water and nanofluid-water streams. The ZnO/Water (0.5%v/v) nanofluid has been used as the hot stream. The heat transfer rate omitted of hot stream and overall heat transfer coefficients in both heat exchangers are measured as a function of hot and cold streams mass flow rates. The experimental results show that the heat transfer rate and heat transfer coefficients of the nanofluid in both of the heat exchangers is higher than that of the base liquid (i.e., water) and the efficiency of plate heat exchange is higher than concentric tube heat exchanger. In the plate heat exchanger the heat transfer coefficient of nanofluid at mcold = mhot = 10 gr/sec is about 20% higher than base fluid and under the same conditions in the concentric heat exchanger is 14% higher than base fluid. The heat transfer rate and heat transfer coefficients increases with increase in mass flow rates of hot and cold streams. Also the CFD1 code is used to simulate the performance of the mentioned heat exchangers. The CFD results are compared to the experimental data and showed good agreement. It is shown that the CFD is a reliable tool for investigation of heat transfer of nanofluids in the various heat exchangers.

Sign in / Sign up

Export Citation Format

Share Document