Double-Direction Pressure Distributions Generated by Vaporizing Metal Foils

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
S. Cai
Keyword(s):  
Metal Forming ◽  
Shock Pressure ◽  
Metal Foil ◽  
Forming Process ◽  
Metal Foils ◽  
Pressure Distributions ◽  
Metal Forming Process ◽  
Foil Specimen

In this work, a research on double-direction pressure distributions (DDPD) induced by vaporizing a single metal foil was conducted. The shock pressure in the up direction revealed the same amplitude as that in the down direction. Based on a comparison of pressure amplitudes between double-direction pressure distributions (DDPD) and single-direction pressure distributions (SDPD), the pressure upward in DDPD was found to be smaller than that in SDPD. In addition, an approach to vary the pressure amplitudes in the up and down directions in DDPD was introduced. Using polyurethane plates in different thicknesses leads to various pressure amplitudes on both sides of the foil specimen. Finally, the application of DDPD in metal forming process was examined. A profile forming part with two bulging zones was successfully manufactured.

scholarly journals Laser Welding of High-strength Aluminium Alloys for the Sheet Metal Forming Process

Procedia CIRP ◽  
2014 ◽  
Vol 18 ◽  
pp. 203-208 ◽  
Author(s):  
J. Enz ◽  
S. Riekehr ◽  
V. Ventzke ◽  
N. Sotirov ◽  
N. Kashaev
Keyword(s):  
Laser Welding ◽  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Aluminium Alloys ◽  
High Strength ◽  
Forming Process ◽  
Metal Forming Process

Application of the Radial Return Method to Compute Stress Increments From Mroz’s Hardening Rule

2000 ◽  
Vol 123 (4) ◽  
pp. 398-402 ◽  
Author(s):  
Sing C. Tang ◽  
Z. Cedric Xia ◽  
Feng Ren
Keyword(s):  
Metal Forming ◽  
Computing Time ◽  
Isotropic Hardening ◽  
Stress Increment ◽  
Anisotropic Hardening ◽  
Forming Process ◽  
Shell Elements ◽  
Hardening Rule ◽  
Metal Forming Process ◽  
Return Method

It is well known in the literature that the isotropic hardening rule in plasticity is not realistic for handling plastic deformation in a simulation of a full sheet-metal forming process including springback. An anisotropic hardening rule proposed by Mroz is more realistic. For an accurate computation of the stress increment for a given strain increment by using Mroz’s rule, the conventional subinterval integration takes excessive computing time. This paper proposes the radial return method to compute such stress increment for saving computing time. Two numerical examples show the efficiency of the proposed method. Even for a sheet model with more than 10,000 thin shell elements, the radial return method takes only 40 percent of the overall computing time by the subinterval integration.

Numerical and Experimental Investigations of Multistage Sheet-Bulk Metal Forming Process with Compound Press Tools

2015 ◽  
Vol 651-653 ◽  
pp. 1153-1158 ◽  
Author(s):  
Bernd Arno Behrens ◽  
Anas Bouguecha ◽  
Milan Vucetic ◽  
Sven Hübner ◽  
Daniel Rosenbusch ◽  
...  
Keyword(s):  
Metal Forming ◽  
Solid Metal ◽  
Experimental Investigations ◽  
Metal Component ◽  
Forming Process ◽  
Bulk Metal ◽  
Bulk Metal Forming ◽  
Process Sequence ◽  
Metal Forming Process ◽  
Flange Forming

Sheet-bulk metal forming is a manufacturing technology, which allows to produce a solid metal component out of a flat sheet. This paper focuses on numerical and experimental investigations of a new multistage forming process with compound press tools. The complete process sequence for the production of this solid metal component consists of three forming stages, which include a total of six production techniques. The first forming stage includes deep drawing, simultaneous cutting and following wall upsetting. In the second forming stage, flange forming combined with cup bottom ironing takes place. In the last stage of the process sequence, the component is sized. To investigate and to improve process parameters such as plastic strain distribution, resulting dimensions and process forces, FEA is performed. Based on these results the developed process is designed.

Optimization of Deep Drawing Processes Using Statistical Design of Experiments

1996 ◽  
Author(s):  
Dietrich Bauer ◽  
Regine Krebs
Keyword(s):  
Mathematical Model ◽  
Analysis Of Variance ◽  
Orthogonal Array ◽  
Deep Drawing ◽  
Metal Forming ◽  
Drawing Process ◽  
Drawing Force ◽  
Forming Process ◽  
Deep Drawing Process ◽  
Metal Forming Process

Abstract For a deep drawing process some important controllable variables (factors) upon the maximum drawing force are analyzed to find a setting adjustment for these process factors that provides a very low force for the metal forming process. For this investigation an orthogonal array L18 with three-fold replication is used. To find the optimum of the process, the experimental results are analyzed in accordance with the robust-design-method according to Taguchi (Liesegang et. al., 1990). For this purpose, so-called Signal-to-Noise-ratios are calculated. The analysis of variance for this S/N-ratios leads to a mathematical model for the deep drawing process. This model allows to find the pressumed optimal settings of the investigated factors. In the following, a confirmation experiment is carried out by using these optimal settings. The maximum drawing force of the confirmation experiment does not correspond with the confidence interval, which was calculated by analysis of variance techniques. So the predicted optimum of the process does not lead to a metal forming process with very low deep drawing force. The comparison with a full factorial plan shows that there are interactions between the investigated factors. These interactions could not be discovered by the used orthogonal array. Thus the established mathematical model does not describe the relation between the factors and deep drawing force in accordance with the practical deep drawing conditions.

FEM Simulation Analysis of Cross Wedge Rolling Process

2011 ◽  
Vol 381 ◽  
pp. 72-75
Author(s):  
Bin Li
Keyword(s):  
Simulation Analysis ◽  
Three Dimensional ◽  
Fem Simulation ◽  
Rolling Process ◽  
Stress Distributions ◽  
Cross Wedge Rolling ◽  
Forming Process ◽  
Pressure Distributions ◽  
Metal Forming Process ◽  
Rolling Load

This paper investigates the interfacial slip between the forming tool and workpiece in a relatively new metal forming process, cross-wedge rolling. Based on the finite elements method, three-dimensional mechanical model of cross wedge rolling process has been developed. Examples of numerical simulation for strain, stress distributions and rolling load components have been included. The main advantages of the finite element method are: the capability of obtaining detailed solutions of the mechanics in a deforming body, namely, stresses, shapes, strains or contact pressure distributions; and the computer codes, can be used for a large variety of problems by simply changing the input data.

Sign in / Sign up

Export Citation Format

Share Document