Effects of Nanoparticle Shape on Slot-Jet Impingement Cooling of a Corrugated Surface With Nanofluids

2017 ◽  
Vol 9 (2) ◽  
Author(s):  
Fatih Selimefendigil ◽  
Hakan F. Öztop
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Jet Impingement ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Corrugated Surface ◽  
Nanoparticle Shapes

Numerical study of jet impingement cooling of a corrugated surface with water–SiO2 nanofluid of different nanoparticle shapes was performed. The bottom wall is corrugated and kept at constant surface temperature, while the jet emerges from a rectangular slot with cold uniform temperature. The finite volume method is utilized to solve the governing equations. The effects of Reynolds number (between 100 and 500), corrugation amplitude (between 0 and 0.3), corrugation frequency (between 0 and 20), nanoparticle volume fraction (between 0 and 0.04), and nanoparticle shapes (spherical, blade, brick, and cylindrical) on the fluid flow and heat transfer characteristics were studied. Stagnation point and average Nusselt number enhance with Reynolds number and solid particle volume fraction for both flat and corrugated surface configurations. An optimal value for the corrugation amplitude and frequency was found to maximize the average heat transfer at the highest value of Reynolds number. Among various nanoparticle shapes, cylindrical ones perform the best heat transfer characteristics in terms of stagnation and average Nusselt number values. At the highest solid volume concentration of the nanoparticles, heat transfer values are higher for a corrugated surface when compared to a flat surface case.

Numerical Study on Flow and Heat Transfer Characteristics of Jet Impingement

2011 ◽  
Author(s):  
Xinjun Wang ◽  
Rui Liu ◽  
Xiaowei Bai ◽  
Jinling Yao
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Target Surface ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

A mathematical model used for studying jet impingement cooling characteristics is established, and the rationality of the calculation model and method is confirmed by the experimental data. The CFX software is used to numerically simulate the jet impingement cooling characteristics on a gas turbine blade. The effects of various parameters, such as the arrays of impinging nozzles, the jet Reynolds number, the jet-to-jet distance, the ratio of nozzle-to-surface spacing to jet diameter H/d, and the radius of curvature of the target surface, on the flow and heat transfer characteristics of a impingement cooling process are studied. The results indicate that the impingement jets can make complex vortex in the cooling channel, the flow boundary layer is extremely thin and highly turbulent. Underneath each impingement nozzle, there will appear a low temperature area and a peak of Nusselt number on the impingement target surface, the distribution of temperature and Nusselt number on the target surface are associated with arrangement of impingement nozzles. The average Nusselt number of the in-line arrangement nozzles is higher than that of the staggered arrangement ones. With the increasing of jet Reynolds number, the velocity impinging on the target surface and Nusselt number increase. However, heat transfer of impingement cooling on target surface is not sensitive to the jet nozzles distance; the velocity impinging on the target surface and Nusselt number decrease with the increasing of the H/d value. For the curved target surface cases, the average Nusselt number of the target surface and the effect of heat transfer decreased with the increasing of curvature radius R.

Effect of Variation of Pin-fin Height on Jet Impingement Heat Transfer on a Rotating Surface

2021 ◽  
Author(s):  
Pratik S. Bhansali ◽  
Srinath V. Ekkad
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Gas Turbine ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Impinging Jet ◽  
Rotating Disc ◽  
Disc Surface ◽  
Pin Fins

Abstract Heat transfer over rotating surfaces is of particular interest in rotating machinery such as gas turbine engines. The rotation of the gas turbine disc creates a radially outward flow on the disc surface, which may lead to ingress of hot gases into the narrow cavity between the disc and the stator. Impingement of cooling jet is an effective way of cooling the disc and countering the ingress of the hot gases. Present study focusses on investigating the effect of introducing pin-fins over the rotating disc on the heat transfer. The jet Reynolds number has been varied from 5000 to 18000, and the rotating Reynolds number has been varied from 5487 to 12803 for an aluminum disc of thickness 6.35mm and diameter 10.16 cm, over which square pins have been arranged in an inline fashion. Steady state temperature measurements have been taken using thermocouples embedded in the disc close to the target surface, and area average Nusselt number has been calculated. The effects of varying the height of the pin-fins, distance between nozzle and the disc surface and the inclination of the impinging jet with the axis of rotation have also been studied. The results have been compared with those for a smooth aluminum disc of equal dimensions and without any pin-fins. The average Nusselt number is significantly enhanced by the presence of pin fins. In the impingement dominant regime, where the effect of disc rotation is minimal for a smooth disc, the heat transfer increases with rotational speed in case of pin fins. The effect of inclination angle of the impinging jet is insignificant in the range explored in this paper (0° to 20°).

Experimental Investigation on Convective Heat Transfer Enhancement of Laminar Slot Jet Impingement in the Presence of Porous Medium

2016 ◽  
Author(s):  
Sampath Kumar Chinige ◽  
Arvind Pattamatta
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Porous Medium ◽  
Porous Media ◽  
Nusselt Number ◽  
Heat Sink ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Transfer Enhancement ◽  
Porous Obstacle

An experimental study using Liquid crystal thermography technique is conducted to study the convective heat transfer enhancement in jet impingement cooling in the presence of porous media. Aluminium porous sample of 10 PPI with permeability 2.48e−7 and porosity 0.95 is used in the present study. Results are presented for two different Reynolds number 400 and 700 with four different configurations of jet impingement (1) without porous foams (2) over porous heat sink (3) with porous obstacle case (4) through porous passage. Jet impingement with porous heat sink showed a deterioration in average Nusselt number by 10.5% and 18.1% for Reynolds number of 400 and 700 respectively when compared with jet impingement without porous heat sink configuration. The results show that for Reynolds number 400, jet impingement through porous passage augments average Nusselt number by 30.73% whereas obstacle configuration enhances the heat transfer by 25.6% over jet impingement without porous medium. Similarly for Reynolds number 700, the porous passage configuration shows average Nusselt number enhancement by 71.09% and porous obstacle by 33.4 % over jet impingement in the absence of porous media respectively.

Numerical Study on Flow and Heat Transfer Characteristics of Jet Impingement Cooling

2011 ◽  
Vol 148-149 ◽  
pp. 680-683
Author(s):  
Run Peng Sun ◽  
Wei Bing Zhu ◽  
Hong Chen ◽  
Chang Jiang Chen
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Cross Flow ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Transfer Characteristic ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics

Three-dimensional numerical study is conducted to investigate the heat transfer characteristics for the flow impingement cooling in the narrow passage based on cooling technology of turbine blade.The effects of the jet Reynolds number, impingement distance and initial cross-flow on heat transfer characteristic are investigated.Results show that when other parameters remain unchanged local heat transfer coefficient increases with increase of jet Reynolds number；overall heat transfer effect is reduced by initial cross-flow；there is an optimal distance to the best effect of heat transfer.

Effectiveness of Jet Impingement Cooling System on Convex Surface

2016 ◽  
Vol 819 ◽  
pp. 74-77
Author(s):  
Mohamad Nor Musa ◽  
Mohamad Faizal Fauzi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Convex Surface ◽  
Cooling System ◽  
Jet Impingement ◽  
Impingement Cooling ◽  
Reynolds Number Increase ◽  
Number Increase

Jet impingement is one of cooling method used in order to achieve high heat transfer coefficient and widely used in industry applications such as drying of textile and film, glass and plastic sheets, cooling of electronic equipment, and heat treatment of metals. In this research, it focused on the effectiveness of the jet impingement cooling system on the convex surface based on mass blowing rate and nozzle exit to surface parameters. The scope of experiment research encompasses are convex surface made of aluminum alloy and diameter 12.5cm. For mass blowing rate parameters, it use ʋjet = 1.98m/s, 3.03m/s, 4.97m/s and 6.00m/s which has Reynolds number range from 643 until 1946. Nozzle exit to surface distance,s/d = 4.0, 8.0 and 12.0. In this experiment model, a major components that involved are a compressor, nozzle, convex surface model, K thermocouple and heater. For the result of the experiment, it is based on the data obtain through a heat transfer coefficient and Nusselt number which the plotted graph focus on the space spacing and Reynolds number parameters. For the graph Nusselt number versus s/d at stagnation point c/d=0, it shown that when the Reynolds number increase, the Nusselt number also increase. In term of effectiveness, the s/d=12.0 has a good effectiveness jet impingement cooling system. For the graph of Nusselt number versus Reynolds at stagnation point, c/d=0, as Reynolds number increase, the Nusselt number increase too. From this experiment the better cooling effect is at Reynolds number, Re=1946. Thus, it can conclude that, effectiveness for jet impingement cooling system on the convex surface occurs at the highest Reynolds number.

Effects of Extended Jet Holes to Heat Transfer and Flow Characteristics of the Jet Impingement Cooling

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Ahmet Ümit Tepe ◽  
Kamil Arslan ◽  
Yaşar Yetişken ◽  
Ünal Uysal
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Flat Surface ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Jet Impingement ◽  
Target Surface ◽  
Impingement Cooling ◽  
Compressor Power

In this study, effects of extended jet holes to heat transfer and flow characteristics of jet impingement cooling were numerically investigated. Cross-flow in the impinging jet cooling adversely affects the heat transfer on the target surface. The main purpose of this study is to reduce the negative effect of cross-flow on heat transfer by extending jet holes toward the target surface with nozzles. This study has been conducted under turbulent flow condition (15,000 ≤ Re  ≤  45,000). The surface of the turbine blade, which is the target surface, has been modeled as a flat plate. The effect of the ribs, placed on the target surface, on the heat transfer has been also investigated, and the results were compared with the flat surface. The parameters such as average and local Nusselt numbers on the target surface, flow characteristics, and compressor power have been examined in detail. It was obtained from the numerical results that the average Nusselt number increases with decreasing the gap between the target surface and the nozzle. In addition, the higher average Nusselt number was obtained on the flat surface than the ribbed surface. The lowest compressor power was achieved in the 5Dj nozzle gap for the flat surface and in the 4Dj nozzle gap for the ribbed surface.

Cooling of a Partially Elastic Isothermal Surface by Nanofluids Jet Impingement

2018 ◽  
Vol 140 (4) ◽  
Author(s):  
Fatih Selimefendigil ◽  
Hakan F. Öztop
Keyword(s):  
Reynolds Number ◽  
Nusselt Number ◽  
Elastic Modulus ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Jet Impingement ◽  
Particle Volume ◽  
Elastic Part ◽  
Hot Surface

Numerical study of nanofluid jet impingement cooling of a partially elastic isothermal hot surface was conducted with finite element method. The impingement surface was made partially elastic, and the effects of Reynolds number (between 25 and 200), solid particle volume fraction (between 0.01 and 0.04), elastic modulus of isothermal hot surface (between 104 and 106), size of the flexible part (between 7.5 w and 25 w), and nanoparticle type (spherical, cylindrical, blade) on the fluid flow and heat transfer characteristics were analyzed. It was observed that average Nusselt number enhances for higher Reynolds number, higher values of elastic modulus of flexible wall, smaller size of elastic part, and higher nanoparticle solid volume fraction and for cylindrical shaped particles. It is possible to change the maximum Nusselt number by 50.58% and 33% by changing the elastic modulus of the hot wall and size of elastic part whereas average Nusselt number changes by only 9.33% and 6.21%. The discrepancy between various particle shapes is higher for higher particle volume fraction.

An Experimental Investigation on Heat Transfer Characteristics of Hot Surface by Using CuO–Water Nanofluids in Circular Jet Impingement Cooling

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Mayank Modak ◽  
Sandesh S. Chougule ◽  
Santosh K. Sahu
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Jet Impingement ◽  
Test Surface ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Hot Surface ◽  
Plate Distance

In the present study, an experimental investigation has been carried out to analyze the heat transfer characteristics of CuO–water nanofluids jet on a hot surface. A rectangular stainless steel foil (AISI-304, 0.15 mm thick) used as the test surface is electrically heated to obtain the required initial temperature (500 °C). The distribution of surface heat flux on the target surface is evaluated from the recorded thermal images during transient cooling. The effect of nanoparticle concentration and Reynolds number of the nanofluids on the heat transfer characteristics is studied. Tests are performed for varied range of Reynolds number (5000 ≤ Re ≤ 12,000), two different CuO–water nanofluids concentration (Ф = 0.15%, 0.6%) and two different nozzle to plate distance (l/d = 6, 12). The enhancement in Nusselt number for CuO–water nanofluids was found to be 14% and 90%, for nanofluids concentration of Ф = 0.15% and Ф = 0.60%, respectively, compared to pure water. The test surface characteristics after nanofluids jet impingement are studied using scanning electron microscope (SEM). Based on the investigation, a correlation among various parameters, namely, Reynolds number (Re), Prandtl number (Pr), nozzle to plate distance (l/d), and Nusselt number (Nu), is presented.

Local Heat Transfer in a Rotating Square Channel With Jet Impingement

1999 ◽  
Vol 121 (4) ◽  
pp. 811-818 ◽  
Author(s):  
S.-S. Hsieh ◽  
J.-T. Huang ◽  
C.-F. Liu
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Local Heat Transfer Coefficient

The influence of rotation and jet mass flow rate on the local heat transfer coefficient for a single confined impinging round jet with a fixed jet-to-wall spacing of H/d = 5 was studied for the jet Reynolds number from 6500 to 26,000 and the rotational Reynolds number from 0 to 112,000. The local heat transfer coefficient along the surface is measured and the effect of the rotation on the stagnation (peak) point, local and average Nusselt number, is presented and discussed. Furthermore, a correlation was developed for the average Nusselt number in terms of the parameters of Rej and ReΩ. In general, the combined jet impingement and rotation effect are shown to affect the heat transfer response. Rotation decreases the average Nusselt number values from 15 to 25 percent in outward and inward radial flow, respectively. Finally, comparisons of the present data with existing results for multijets with rotation were also made.

scholarly journals Numerical Investigations on Heat Transfer Characteristics of Single Particle and Hybrid Nanofluids in Uniformly Heated Tube

Symmetry ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 876
Author(s):  
Kunal Sandip Garud ◽  
Moo-Yeon Lee
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Performance Evaluation ◽  
Friction Factor ◽  
Volume Fraction ◽  
Evaluation Criteria ◽  
Hybrid Nanofluid ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

In the present study, the heat transfer characteristics, namely, heat transfer coefficient, Nusselt number, pressure drop, friction factor and performance evaluation criteria are evaluated for water, Al2O3 and Al2O3/Cu nanofluids. The effects of Reynolds number, volume fraction and composition of nanoparticles in hybrid nanofluid are analyzed for all heat transfer characteristics. The single particle and hybrid nanofluids are flowing through a plain straight tube which is symmetrically heated under uniform heat flux condition. The numerical model is validated for Nusselt number within 7.66% error and friction factor within 8.83% error with corresponding experimental results from the previous literature study. The thermophysical properties of hybrid nanofluid are superior to the single particle nanofluid and water. The heat transfer coefficient, Nusselt number and pressure drop show increasing trend with increase in the Reynolds number and volume fraction. The friction factor shows the parabolic trend, and the performance evaluation criteria shows small variations with change in Reynolds number. However, both friction factor and performance evaluation criteria have increased with increase in the volume fraction. The 2.0% Al2O3/Cu with equal composition of both nanoparticles (50/50%) have presented superior heat transfer characteristics among all working fluids. Further, the heat transfer characteristics of 2.0% Al2O3/Cu hybrid nanofluid are enhanced by changing the nanoparticle compositions. The performance evaluation criteria for 2.0% Al2O3, 2.0% Al2O3/Cu (50/50%), 2.0% Al2O3/Cu (75/25%) and 2.0% Al2O3/Cu (25/75%) are evaluated as 1.08, 1.11, 1.10 and 1.12, respectively.

Sign in / Sign up

Export Citation Format

Share Document