Influence of Liquid Properties on Energy Conversion During Crown Evolution Following Drop Impact Upon Films

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Yujia Zhang ◽  
Peiqing Liu ◽  
Qiulin Qu ◽  
Fanglin Liu ◽  
Ramesh K. Agarwal
Keyword(s):  
Reynolds Number ◽  
Energy Conversion ◽  
Weber Number ◽  
Stokes Equations ◽  
Drop Impact ◽  
Navier Stokes ◽  
Impact Process ◽  
Vof Model ◽  
The Moment ◽  
The Impact

Abstract The energy conversion is proposed to analyze the effects of liquid properties on the formation of an ejecta sheet, prompt splashing, and crown evolution. The incompressible laminar Navier–Stokes equations coupled with the volume-of-fluid (VOF) model are solved numerically in an axisymmetric frame to simulate the impact process. Based on the energy conversion curves and liquid–gas interface shapes, the Weber number is shown to be the main dimensionless quantity controlling the impact process, especially with regard to crown evolution. However, the Reynolds number does have some influence on the drop impact process, especially during the stage of ejecta sheet formation and prompt splashing. By studying energy conversion during the impact process, the crown evolution is shown to be accelerated significantly with decreasing Weber number, but is hardly affected by the Reynolds number. A linear relation is found between the time to the moment of crown stabilization (when the crown height reaches its maximum value) and the square root of the Weber number. The relationship between the Weber number and the energy distribution at the moment of crown stabilization is also studied.

scholarly journals Modelling turbulent skin-friction control using linearized Navier–Stokes equations

2012 ◽  
Vol 702 ◽  
pp. 403-414 ◽  
Author(s):  
C. A. Duque-Daza ◽  
M. F. Baig ◽  
D. A. Lockerby ◽  
S. I. Chernyshenko ◽  
C. Davies
Keyword(s):  
Reynolds Number ◽  
Skin Friction ◽  
Stokes Equations ◽  
Travelling Waves ◽  
Close Correlation ◽  
Friction Reduction ◽  
Navier Stokes ◽  
Clear Correlation ◽  
Navier Stokes Equations ◽  
The Impact

AbstractLinearized Navier–Stokes equations are solved to investigate the impact on the growth of near-wall turbulent streaks that arises from streamwise-travelling waves of spanwise wall velocity. The percentage change in streak amplification due to the travelling waves, over a range of wave parameters, is compared to published direct numerical simulation (DNS) predictions of turbulent skin-friction reduction; a clear correlation between the two is observed. Linearized simulations at a much higher Reynolds number, more relevant to aerospace applications, produce results that show no marked differences to those obtained at low Reynolds number. It is also observed that there is a close correlation between DNS data of drag reduction and a very simple characteristic of the ‘generalized’ Stokes layer generated by the streamwise-travelling waves.

scholarly journals Numerical analysis of high-lift configurations with oscillating flaps

2021 ◽  
Author(s):  
Johannes Ruhland ◽  
Christian Breitsamter
Keyword(s):  
Reynolds Number ◽  
Flow Separation ◽  
Separated Flow ◽  
Navier Stokes ◽  
Rotational Axis ◽  
High Lift ◽  
Hinge Point ◽  
Reduced Frequency ◽  
Flap Deflection ◽  
The Impact

AbstractThis study presents two-dimensional aerodynamic investigations of various high-lift configuration settings concerning the deflection angles of droop nose, spoiler and flap in the context of enhancing the high-lift performance by dynamic flap movement. The investigations highlight the impact of a periodically oscillating trailing edge flap on lift, drag and flow separation of the high-lift configuration by numerical simulations. The computations are conducted with regard to the variation of the parameters reduced frequency and the position of the rotational axis. The numerical flow simulations are conducted on a block-structured grid using Reynolds Averaged Navier Stokes simulations employing the shear stress transport $$k-\omega $$ k - ω turbulence model. The feature Dynamic Mesh Motion implements the motion of the oscillating flap. Regarding low-speed wind tunnel testing for a Reynolds number of $$0.5 \times 10^{6}$$ 0.5 × 10 6 the flap movement around a dropped hinge point, which is located outside the flap, offers benefits with regard to additional lift and delayed flow separation at the flap compared to a flap movement around a hinge point, which is located at 15 % of the flap chord length. Flow separation can be suppressed beyond the maximum static flap deflection angle. By means of an oscillating flap around the dropped hinge point, it is possible to reattach a separated flow at the flap and to keep it attached further on. For a Reynolds number of $$20 \times 10^6$$ 20 × 10 6 , reflecting full scale flight conditions, additional lift is generated for both rotational axis positions.

scholarly journals Dynamics of Single Droplet Splashing on Liquid Film by Coupling FVM with VOF

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 841
Author(s):  
Yuzhen Jin ◽  
Huang Zhou ◽  
Linhang Zhu ◽  
Zeqing Li
Keyword(s):  
Liquid Film ◽  
Weber Number ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Single Droplet ◽  
Navier Stokes Equations ◽  
Volume Method ◽  
The Relationship

A three-dimensional numerical study of a single droplet splashing vertically on a liquid film is presented. The numerical method is based on the finite volume method (FVM) of Navier–Stokes equations coupled with the volume of fluid (VOF) method, and the adaptive local mesh refinement technology is adopted. It enables the liquid–gas interface to be tracked more accurately, and to be less computationally expensive. The relationship between the diameter of the free rim, the height of the crown with different numbers of collision Weber, and the thickness of the liquid film is explored. The results indicate that the crown height increases as the Weber number increases, and the diameter of the crown rim is inversely proportional to the collision Weber number. It can also be concluded that the dimensionless height of the crown decreases with the increase in the thickness of the dimensionless liquid film, which has little effect on the diameter of the crown rim during its growth.

A note on the solution of the Navier-Stokes equations for a spherically symmetric expansion into a very low pressure

1973 ◽  
Vol 59 (2) ◽  
pp. 391-396 ◽  
Author(s):  
N. C. Freeman ◽  
S. Kumar
Keyword(s):  
Shock Wave ◽  
Reynolds Number ◽  
Stokes Equation ◽  
Stokes Equations ◽  
Low Pressure ◽  
Navier Stokes ◽  
Spherically Symmetric ◽  
Navier Stokes Equation ◽  
Navier Stokes Equations ◽  
Type Flow

It is shown that, for a spherically symmetric expansion of a gas into a low pressure, the shock wave with area change region discussed earlier (Freeman & Kumar 1972) can be further divided into two parts. For the Navier–Stokes equation, these are a region in which the asymptotic zero-pressure behaviour predicted by Ladyzhenskii is achieved followed further downstream by a transition to subsonic-type flow. The distance of this final region downstream is of order (pressure)−2/3 × (Reynolds number)−1/3.

scholarly journals Finite-amplitude steady waves in plane viscous shear flows

1985 ◽  
Vol 160 ◽  
pp. 281-295 ◽  
Author(s):  
F. A. Milinazzo ◽  
P. G. Saffman
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Stokes Equations ◽  
Reynolds Numbers ◽  
Finite Amplitude ◽  
Linear Instability ◽  
Navier Stokes ◽  
Unidirectional Flow ◽  
Viscous Shear ◽  
Finite Amplitude Waves

Computations of two-dimensional solutions of the Navier–Stokes equations are carried out for finite-amplitude waves on steady unidirectional flow. Several cases are considered. The numerical method employs pseudospectral techniques in the streamwise direction and finite differences on a stretched grid in the transverse direction, with matching to asymptotic solutions when unbounded. Earlier results for Poiseuille flow in a channel are re-obtained, except that attention is drawn to the dependence of the minimum Reynolds number on the physical constraint of constant flux or constant pressure gradient. Attempts to calculate waves in Couette flow by continuation in the velocity of a channel wall fail. The asymptotic suction boundary layer is shown to possess finite-amplitude waves at Reynolds numbers orders of magnitude less than the critical Reynolds number for linear instability. Waves in the Blasius boundary layer and unsteady Rayleigh profile are calculated by employing the artifice of adding a body force to cancel the spatial or temporal growth. The results are verified by comparison with perturbation analysis in the vicinity of the linear-instability critical Reynolds numbers.

Fast forced liquid film spreading on a substrate: flow, heat transfer and phase transition

2010 ◽  
Vol 656 ◽  
pp. 189-204 ◽  
Author(s):  
ILIA V. ROISMAN
Keyword(s):  
Heat Transfer ◽  
Phase Transition ◽  
Stokes Equations ◽  
Substrate Surface ◽  
Reynolds Numbers ◽  
Drop Impact ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Theoretical Predictions ◽  
Viscous Drop

This theoretical study is devoted to description of fluid flow and heat transfer in a spreading viscous drop with phase transition. A similarity solution for the combined full Navier–Stokes equations and energy equation for the expanding lamella generated by drop impact is obtained for a general case of oblique drop impact with high Weber and Reynolds numbers. The theory is applicable to the analysis of the phenomena of drop solidification, target melting and film boiling. The theoretical predictions for the contact temperature at the substrate surface agree well with the existing experimental data.

Parameter Extension Simulation of Turbulent Flows in a Compressor Cascade With a High Reynolds Number

2020 ◽  
Author(s):  
Yan Jin
Keyword(s):  
Reynolds Number ◽  
Turbulent Flow ◽  
Turbulent Flows ◽  
Stokes Equations ◽  
Simulation Method ◽  
Potential Method ◽  
Navier Stokes ◽  
Reference Solution ◽  
Compressor Cascade ◽  
High Reynolds

Abstract The turbulent flow in a compressor cascade is calculated by using a new simulation method, i.e., parameter extension simulation (PES). It is defined as the calculation of a turbulent flow with the help of a reference solution. A special large-eddy simulation (LES) method is developed to calculate the reference solution for PES. Then, the reference solution is extended to approximate the exact solution for the Navier-Stokes equations. The Richardson extrapolation is used to estimate the model error. The compressor cascade is made of NACA0065-009 airfoils. The Reynolds number 3.82 × 105 and the attack angles −2° to 7° are accounted for in the study. The effects of the end-walls, attack angle, and tripping bands on the flow are analyzed. The PES results are compared with the experimental data as well as the LES results using the Smagorinsky, k-equation and WALE subgrid models. The numerical results show that the PES requires a lower mesh resolution than the other LES methods. The details of the flow field including the laminar-turbulence transition can be directly captured from the PES results without introducing any additional model. These characteristics make the PES a potential method for simulating flows in turbomachinery with high Reynolds numbers.

Free-stream coherent structures in parallel boundary-layer flows

2014 ◽  
Vol 752 ◽  
pp. 602-625 ◽  
Author(s):  
Kengo Deguchi ◽  
Philip Hall
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Coherent Structures ◽  
Free Stream ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Homotopy Continuation ◽  
Boundary Layer Flows ◽  
Navier Stokes Equations ◽  
High Reynolds

AbstractOur concern in this paper is with high-Reynolds-number nonlinear equilibrium solutions of the Navier–Stokes equations for boundary-layer flows. Here we consider the asymptotic suction boundary layer (ASBL) which we take as a prototype parallel boundary layer. Solutions of the equations of motion are obtained using a homotopy continuation from two known types of solutions for plane Couette flow. At high Reynolds numbers, it is shown that the first type of solution takes the form of a vortex–wave interaction (VWI) state, see Hall & Smith (J. Fluid Mech., vol. 227, 1991, pp. 641–666), and is located in the main part of the boundary layer. On the other hand, here the second type is found to support an equilibrium solution of the unit-Reynolds-number Navier–Stokes equations in a layer located a distance of $\def \xmlpi #1{}\def \mathsfbi #1{\boldsymbol {\mathsf {#1}}}\let \le =\leqslant \let \leq =\leqslant \let \ge =\geqslant \let \geq =\geqslant \def \Pr {\mathit {Pr}}\def \Fr {\mathit {Fr}}\def \Rey {\mathit {Re}}O(\ln \mathit{Re})$ from the wall. Here $\mathit{Re}$ is the Reynolds number based on the free-stream speed and the unperturbed boundary-layer thickness. The streaky field produced by the interaction grows exponentially below the layer and takes its maximum size within the unperturbed boundary layer. The results suggest the possibility of two distinct types of streaky coherent structures existing, possibly simultaneously, in disturbed boundary layers.

scholarly journals Nonlinear amplification in hydrodynamic turbulence

2021 ◽  
Vol 930 ◽  
Author(s):  
Kartik P. Iyer ◽  
Katepalli R. Sreenivasan ◽  
P.K. Yeung
Keyword(s):  
Reynolds Number ◽  
Isotropic Turbulence ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Developed Turbulence ◽  
Advection Term ◽  
Nonlinear Amplification

Using direct numerical simulations performed on periodic cubes of various sizes, the largest being $8192^3$ , we examine the nonlinear advection term in the Navier–Stokes equations generating fully developed turbulence. We find significant dissipation even in flow regions where nonlinearity is locally absent. With increasing Reynolds number, the Navier–Stokes dynamics amplifies the nonlinearity in a global sense. This nonlinear amplification with increasing Reynolds number renders the vortex stretching mechanism more intermittent, with the global suppression of nonlinearity, reported previously, restricted to low Reynolds numbers. In regions where vortex stretching is absent, the angle and the ratio between the convective vorticity and solenoidal advection in three-dimensional isotropic turbulence are statistically similar to those in the two-dimensional case, despite the fundamental differences between them.

Sign in / Sign up

Export Citation Format

Share Document