Thermal Characteristics of a Three-Dimensional Coil Type Pulsating Heat Pipe at Different Heating Modes

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Satyanand Abraham ◽  
Anand Takawale ◽  
Peter Stephan ◽  
Arvind Pattamatta
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Heat Input ◽  
3D Structure ◽  
Three Dimensional ◽  
Working Fluid ◽  
Coolant Temperature ◽  
Pulsating Heat Pipe ◽  
Condenser Section ◽  
Maximum Heat

Abstract The heat transfer performance of a pulsating heat pipe (PHP) configured as a three-dimensional (3D) structure is reported in the present study. The PHP structure resembles an elongated coil and termed “coil type PHP.” Five different heating modes were created by positioning the evaporator at different locations and placing the PHP device in vertical and horizontal orientations. Studies were conducted primarily with de-ionized water as the working fluid. Limited number of experiments were also performed using binary fluids. The filling ratio was varied from 40% to 80%, while the heat input was varied from 20 W to 240 W. The vertical and horizontal orientations show almost 30 and 10 times reduction in the thermal resistance, respectively, compared with bare PHP tubes without the working fluid. This results in an effective thermal conductivity of more than 3000 W/(m K) and 12,000 W/(m K) for horizontal and vertical orientations, respectively. The use of the binary fluid (10 wt% and 20 wt% of ethanol aqueous solution) results in an increase in the maximum heat input at different heating modes. The temperature of the coolant supplied to the condenser section of the PHP was also varied, and the thermal resistance of the system was observed to reduce with an increase in the coolant temperature.

Experimental and Numerical Simulation for Thermal Investigation of Oscillating Heat Pipe Using VOF Model

2020 ◽  
Vol 38 (1A) ◽  
pp. 88-104
Author(s):  
Anwar S. Barrak ◽  
Ahmed A. M. Saleh ◽  
Zainab H. Naji
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Heat Input ◽  
Cfd Simulation ◽  
Working Fluid ◽  
Maximum Deviation ◽  
Inlet Temperature ◽  
Maximum Heat ◽  
Oscillating Heat Pipe ◽  
Vof Model

This study is investigated the thermal performance of seven turns of the oscillating heat pipe (OHP) by an experimental investigation and CFD simulation. The OHP is designed and made from a copper tube with an inner diameter 3.5 mm and thickness 0.6 mm and the condenser, evaporator, and adiabatic lengths are 300, 300, and 210 mm respectively.  Water is used as a working fluid with a filling ratio of 50% of the total volume. The evaporator part is heated by hot air (35, 40, 45, and 50) oC with various face velocity (0.5, 1, and 1.5) m/s. The condenser section is cold by air at temperature 15 oC. The CFD simulation is done by using the volume of fluid (VOF) method to model two-phase flow by conjugating a user-defined function code (UDF) to the FLUENT code. Results showed that the maximum heat input is 107.75 W while the minimum heat is 13.75 W at air inlet temperature 35 oC with air velocity 0.5m/s. The thermal resistance decreased with increasing of heat input. The results were recorded minimum thermal resistance 0.2312 oC/W at 107.75 W and maximum thermal resistance 1.036 oC/W at 13.75W. In addition, the effective thermal conductivity increased due to increasing heat input.  The numerical results showed a good agreement with experimental results with a maximum deviation of 15%.

Experimental Investigation of Heat Transfer of Refrigerant Fluid Pulsating Heat Pipe

2017 ◽  
Vol 865 ◽  
pp. 137-142
Author(s):  
Somchai Maneewan ◽  
Chantana Punlek ◽  
Hoy Yen Chan ◽  
Atthakorn Thongtha
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Temperature Difference ◽  
Heat Input ◽  
Filling Ratio ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Filling Volume ◽  
Volume Filling

Heat transfer performances of a pulsating heat pipe (PHP) having internal and external diameter with 4.5 mm and 6 mm with various contents of refrigerant are experimentally investigated. The working fluid as R404A refrigerant was filled in the volume ratios from 0% to 80% and the heat input was controlled in the range from 10 W to 80 W. Obtained results exhibited the ability of R404A refrigerant can enhance the thermal performance in steady state condition. The average temperature difference of the evaporating section and condensing section in the 80% filling volume ratio decreased from 9.5 °C to 2.5 °C when the heating power increase from 10 W to 80 W. The thermal resistance of evaporator and condenser decreased with an increase of the heat input as well. For other filling volume ratios, the trend of temperature difference and thermal resistance was similar to that of the 80% volume filling ratio. Considering the same heat input, the highest heat transfer performance was found at the 80% volume filling ratio. Refrigerant with a relatively low dynamic consistency can lead to relatively high velocity in the PHP that can reduce the temperature difference between the evaporating section and condensing section.

Thermal Resistance of a Rotating Closed-Loop Pulsating Heat Pipe: Effect of Centrifugal Accelerations

2016 ◽  
Vol 851 ◽  
pp. 292-298
Author(s):  
Niti Kammuang-Lue ◽  
Deuansavanh Phommavongsa ◽  
Kritsada On-Ai ◽  
Phrut Sakulchangsatjatai ◽  
Pradit Terdtoon
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Closed Loop ◽  
Working Fluid ◽  
Outer Side ◽  
Gravitational Acceleration ◽  
Pulsating Heat Pipe ◽  
Centrifugal Acceleration ◽  
Condenser Section ◽  
Evaporator Section

Objective of this study is to experimentally investigate the effect of centrifugal accelerations on thermal resistance of the rotating closed-loop pulsating heat pipe (RCLPHP). The RCLPHPs were made of a copper tube with internal diameter of 1.50 and 1.78 mm and bent into flower’s petal-shape and arranged into a circle with 11 turns. The evaporator section located at the outer end of the bundle while the condenser section placed around the center of the RCLPHP with no adiabatic section. Both sections had an identical length of 50 mm. R123, and ethanol was filled as working fluid respectively. The RCLPHP was installed on the test rig and it was rotated by the DC motor at the centrifugal acceleration of 0.5, 1, 3, 5, 10, and 20 times of the gravitational acceleration considering at the connection between the evaporator and condenser section. Heat input was generated by electrical annular-plate heaters and varied from 30 to 50, 100, 150, and 200 W. Ceramic papers, wooden plate, and insulation sheet were consecutively attached on the outer side of the heaters in order to prevent the heat loss from the heater. It can be concluded that when the centrifugal acceleration increases, the thermal resistance continuously decreases since the condensate flows back to the evaporator section more rapidly.

Experimental Study of the Effects of Ferrofluid on Thermal Performance of a Pulsating Heat Pipe

2011 ◽  
Author(s):  
Maziar Mohammadi ◽  
Mohammad Mohammadi ◽  
Amir R. Ghahremani ◽  
M. B. Shafii
Keyword(s):  
Magnetic Field ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Input ◽  
Pure Water ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Water Based ◽  
The Magnetic Field

In this work, a four-turn Pulsating Heat Pipe (PHP) is fabricated and tested experimentally. The novelty of the present PHP is the capability of obtaining various thermal performances at a specific heat input by changing the magnetic field. The effects of working fluid (water and ferrofluid), charging ratio (25%, 40%, and 55%), heat input (25, 35, 45, 55, 65, 75, and 85 W), orientation (vertical and horizontal heat mode), and magnetic field on the thermal performance of PHPs are investigated. The results showed that applying the magnetic field on the water based ferrofluid reduced the thermal resistance of PHP by a factor of 40.5% and 38.3% in comparison with the pure water case for the vertical and horizontal mode, respectively. According to the experimental results, an optimum thermal resistance of 0.38 °C/W was achieved at the following conditions: water-based ferrofluid as the working fluid in the presence of magnetic field, vertical mode, charging ratio of 55%, 7% volumetric concentration, and 85 W heat input. This thermal resistance is 11.5 times better than that of the empty PHP.

scholarly journals Effect of Working Fluid on Thermal Performance of Closed Loop Pulsating Heat Pipe

2019 ◽  
Vol 9 (2) ◽  
pp. 953-956
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Closed Loop ◽  
Filling Ratio ◽  
Working Fluid ◽  
External Diameter ◽  
Pulsating Heat Pipe ◽  
Condenser Section ◽  
Heat Transfer Efficiency ◽  
Bottom Heat

The pulsing heat pipe (PHP) is an technology that is increasingly capable of applying many manufacturing areas, but a thorough knowledge of its thermo-hydrodynamic There's far from enough system. This research explored the features of oscillation and the heat transfer efficiency of a closed-loop PHP using an internal and external diameter copper tube with 2.0 and 3.0 mm respectively. For all experimentation, filling ratio (FR) was 40%, five turns and different heat inputs of 20 to 80 W was supplied to PHP. The position of the PHP was vertical bottom heat type. 52 mm, 170 mm,60 mm was retained for the duration of the evaporator, adiabatic and condenser section. Water, Ethanol are chosen as working liquids. To understand, thermal resistance features and median evaporator pressures for multiple operating liquids at distinct heat inputs. An significant consideration for the results of PHPs is the research on PHP stated operating fluid. The result demonstrates that, with the rise of the heating output from 20 to 80 W, where as steadily increases above 80W, the thermal resistance reduces faster. By comparing Water , Ethanol working fluids, Ethanol provides the highest heat performance . The simulation is performed in Mat lab and the results have been contrasted

scholarly journals Non-Uniform Three-Dimensional Pulsating Heat Pipe for Anti-Gravity High-Flux Applications

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3068
Author(s):  
Chih-Yung Tseng ◽  
Kai-Shing Yang ◽  
Chi-Chuan Wang
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Three Dimensional ◽  
Input Power ◽  
Resistance Ratio ◽  
Working Fluid ◽  
High Flux ◽  
Pulsating Heat Pipe ◽  
Unbalance Force ◽  
Three Dimensional Configuration

This study proposes a novel high-flux pulsating heat pipe that can lift the major constraint of the conventional pulsating heat pipe (PHP) which is unable to function properly upon anti-gravity operations. The proposed PHP introduces additional unbalance force via uneven tube diameter/geometry in the adiabatic sections to tailor the problem in anti-gravity operation. The design contains a three-dimensional configuration circuitry with compact arrangement tubes on the evaporator and condenser. Through this design, the non-uniform three-dimensional pulsating heat pipe (3D-PHP) manipulates the uneven inner diameters of the adiabatic sections to form uneven vapor/liquid distributions in the adiabatic sections to yield a unitary flow pattern that is able to withstand a much higher input power. The present PHP uses methanol as working fluid, with 38% volumetric filling ratio, and has a high-flux of 22.9 W/cm2 and a low the thermal resistance ratio (Ranti-gravity/Rgravity-assisted) of 1.05 when the input power is 800 W. Both the heat flux and thermal resistance ratio for the proposed design are far better than the existing literature.

scholarly journals Integration of a Pulsating Heat Pipe in a Flat Plate Heat Sink

2014 ◽  
Author(s):  
Mitchell P. Hoesing ◽  
Gregory J. Michna
Keyword(s):  
Thermal Resistance ◽  
Flat Plate ◽  
Heat Pipe ◽  
Heat Sink ◽  
New Technologies ◽  
Operating Conditions ◽  
Working Fluid ◽  
High Heat Flux ◽  
Pulsating Heat Pipe ◽  
Plate Heat

The ongoing development of faster and smaller electronic components has led to a need for new technologies to effectively dissipate waste thermal energy. The pulsating heat pipe (PHP) shows potential to meet this need, due to its high heat flux capacity, simplicity, and low cost. A 20-turn flat plate PHP was integrated into an aluminum flat plate heat sink with a simulated electronic load. The PHP heat sink used water as the working fluid and had 20 parallel channels with dimensions 2 mm × 2 mm × 119 mm. Experiments were run under various operating conditions, and thermal resistance of the PHP was calculated. The performance enhancement provided by the PHP was assessed by comparing the thermal resistance of the heat sink with no working fluid to that of it charged with water. Uncharged, the PHP was found to have a resistance of 1.97 K/W. Charged to a fill ratio of approximately 75% and oriented vertically, the PHP achieved a resistance of .49 K/W and .53 K/W when the condenser temperature was set to 20°C and 30°C, respectively. When the PHP was tilted to 45° above horizontal the PHP had a resistance of .76 K/W and .59 K/W when the condenser was set 20°C and 30°C, respectively. The PHP greatly improves the heat transfer properties of the heat sink compared to the aluminum plate alone. Additional considerations regarding flat plate PHP design are also presented.

Effect of Inclination Angle on the Closed Loop Pulsating Heat Pipe Thermal Performance

2013 ◽  
Author(s):  
Pramod R. Pachghare ◽  
Ashish M. Mahalle
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Inclination Angle ◽  
Heat Input ◽  
Closed Loop ◽  
Pulsating Heat Pipe ◽  
Working Fluids ◽  
Inclination Angles ◽  
R 134A

The closed loop pulsating heat pipe (CLPHP) is a passive two-phase heat transfer device, patented by Akachi (1990). Due to its excellent features, PHP has been considered as one of the promising technologies for electronic cooling, heat exchanger, etc. This paper presents an experimental study shows the effect of inclination angle on the thermal performance of CLPHP, which consist of 10 turns of copper tubes having inner and outer diameter 2 mm and 3.6 mm respectively. The equal lengths of evaporator, condenser and adiabatic sections are 50 mm each. Different working fluids are used as R-134a, Methanol and Water. For all experimentations, an optimum filling ratio was maintained 50% by volume. The thermal performance have been investigated with different inclination angles (viz. 0°, 20°, 40°, 60° and 90°) at various heat input from 5 to 50W in the steps of 5W. The thermal resistance (which is inversely proportional to thermal performance) of CLPHP at various heat input are plotted for different working fluids. The result shows that, the thermal resistance decreases as heat input increases. But at low heat input i.e. upto 25W, the thermal resistance decreases rapidly and the PHP performance is more sensitive to the inclination angle whereas high heat input i.e. above 25W, the thermal resistance decreases smoothly and less independent to the inclination angle. In all inclination angles, vertical bottom heat position (at 90°) of CLPHP gives best thermal performance due to presence of gravity force. At all inclination angles, the working fluid R-134a show best thermal performance followed by methanol and water.

Thermal Performance of an Open Loop Pulsating Heat Pipe With Ferrofluid (Magnetic Nano-Fluid)

2012 ◽  
Author(s):  
Mehdi Taslimifar ◽  
Maziar Mohammadi ◽  
Mohammad Hassan Saidi ◽  
Hossein Afshin ◽  
Mohammad Behshad Shafii ◽  
...  
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Inclination Angle ◽  
Open Loop ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Degree Relative ◽  
Nano Fluid ◽  
Transfer Capability

In the present research an experimental investigation is performed to explore the effects of working fluid, heat input, ferrofluid concentration, magnets location, and inclination angle on the thermal performance of an Open Loop Pulsating Heat Pipe (OLPHP). Obtained results show that using ferrofluid can improve the thermal performance and applying a magnetic field on the water based ferrofluid decreases the thermal resistance. It shows that at an inclination angle of the OLPHP to be zero, the thermal performance of the present OLPHP reduces. Best heat transfer capability was achieved at 67.5 degree relative to horizontal axis for all of working fluids. Variation of the magnets location leads to a different thermal resistance in the OLPHP charged with ferrofluid.

scholarly journals Thermal analysis of heat pipe using self rewetting fluids

2011 ◽  
Vol 15 (3) ◽  
pp. 879-888 ◽  
Author(s):  
Rathinasamy Senthilkumar ◽  
Subaiah Vaidyanathan ◽  
Sivaramanb Balasubramanian
Keyword(s):  
Surface Tension ◽  
Heat Pipe ◽  
Heat Transport ◽  
Pure Water ◽  
Heat Pipes ◽  
The Self ◽  
Working Fluid ◽  
Surface Tension Gradient ◽  
Condenser Section ◽  
Maximum Heat

This paper discuses the use of self rewetting fluids in the heat pipe. In conventional heat pipes, the working fluid used has a negative surface-tension gradient with temperature. It is an unfavourable one and it decreases the heat transport between the evaporator section and the condenser section. Self rewetting fluids are dilute aqueous alcoholic solutions which have the number of carbon atoms more than four. Unlike other common liquids, self-rewetting fluids have the property that the surface tension increases with temperature up to a certain limit. The experiments are conducted to improve the heat-transport capability and thermal efficiency of capillary assisted heat pipes with the self rewetting fluids like aqueous solutions of n-Butanol and n-Pentanol and its performance is compared with that of pure water. The n-Butanol and n-Pentanol are added to the pure water at a concentration of 0.001moles/lit to prepare the self rewetting fluids. The heat pipes are made up of copper container with a two-layered stainless steel wick consisting of mesh wrapped screen. The experimental results show that the maximum heat transport of the heat pipe is enhanced and the thermal resistances are considerably decreased than the traditional heat pipes filled with water. The fluids used exhibit an anomalous increase in the surface tension with increasing temperature.

Sign in / Sign up

Export Citation Format

Share Document