scholarly journals Thermal analysis of heat pipe using self rewetting fluids

2011 ◽  
Vol 15 (3) ◽  
pp. 879-888 ◽  
Author(s):  
Rathinasamy Senthilkumar ◽  
Subaiah Vaidyanathan ◽  
Sivaramanb Balasubramanian
Keyword(s):  
Surface Tension ◽  
Heat Pipe ◽  
Heat Transport ◽  
Pure Water ◽  
Heat Pipes ◽  
The Self ◽  
Working Fluid ◽  
Surface Tension Gradient ◽  
Condenser Section ◽  
Maximum Heat

This paper discuses the use of self rewetting fluids in the heat pipe. In conventional heat pipes, the working fluid used has a negative surface-tension gradient with temperature. It is an unfavourable one and it decreases the heat transport between the evaporator section and the condenser section. Self rewetting fluids are dilute aqueous alcoholic solutions which have the number of carbon atoms more than four. Unlike other common liquids, self-rewetting fluids have the property that the surface tension increases with temperature up to a certain limit. The experiments are conducted to improve the heat-transport capability and thermal efficiency of capillary assisted heat pipes with the self rewetting fluids like aqueous solutions of n-Butanol and n-Pentanol and its performance is compared with that of pure water. The n-Butanol and n-Pentanol are added to the pure water at a concentration of 0.001moles/lit to prepare the self rewetting fluids. The heat pipes are made up of copper container with a two-layered stainless steel wick consisting of mesh wrapped screen. The experimental results show that the maximum heat transport of the heat pipe is enhanced and the thermal resistances are considerably decreased than the traditional heat pipes filled with water. The fluids used exhibit an anomalous increase in the surface tension with increasing temperature.

Effect of Fluid Loading on the Performance of Wicked Heat Pipes

Volume 3 ◽  
2004 ◽  
Author(s):  
R. Kempers ◽  
A. Robinson ◽  
C. Ching ◽  
D. Ewing
Keyword(s):  
Heat Flux ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heat Pipes ◽  
Working Fluid ◽  
Fluid Loading ◽  
Maximum Heat ◽  
Horizontal Orientation ◽  
Maximum Heat Flux ◽  
Dry Out

A study was performed to experimentally characterize the effect of fluid loading on the heat transport performance of wicked heat pipes. In particular, experiments were performed to characterize the performance of heat pipes with insufficient fluid to saturate the wick and excess fluid for a variety of orientations. It was found that excess working fluid in the heat pipe increased the thermal resistance of the heat pipe, but increased maximum heat flux through the pipe in a horizontal orientation. The thermal performance of the heat pipe was reduced when the amount of working fluid was less than required to saturate the wick, but the maximum heat flux through the heat pipe was significantly reduced at all orientations. It was also found in this case the performance of this heat pipe deteriorated once dry-out occurred.

Effect of Self-Rewetting Fluids on Pulsating Heat Pipe Thermal Performance

2009 ◽  
Author(s):  
Koji Fumoto ◽  
Masahiro Kawaji ◽  
Tsuyoshi Kawanami
Keyword(s):  
Surface Tension ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heated Surface ◽  
Pure Water ◽  
Channel Cross Section ◽  
Working Fluid ◽  
High Heat Flux ◽  
Aqueous Alcohol ◽  
Water Mixture

Pulsating heat pipes (PHPs) have recently emerged as a possible cooling device for high heat flux electronics to replace conventional cooling devices. In this study, new experimental results were obtained for using self-rewetting fluids to enhance the heat transport of PHPs. Unlike other common liquids, the surface tension of self-rewetting fluids increases with temperature. The increase in surface tension at high temperatures causes the liquid to be drawn towards a heated surface if a dry spot appears, which improves boiling heat transfer. PHPs were constructed out of multiport extruded aluminum tubing with a square channel cross section. In experiments, heptanol was added to water at a concentration of less than 1 wt% to form the self-rewetting fluid. Several other parameters were adjusted for optimization, such as the aqueous alcohol solution concentration of the working fluid, the fluid fill ratio, and the heat pipe orientation. Using a self-rewetting fluid in PHPs was found to be highly effective in improving their heat transport capability. The PHPs delivered a better performance when oriented vertically rather than horizontally. As a working fluid, the heptanol water mixture outperformed both the butanol water mixture and pure water within the parameters of this experiment.

Performance Improvement in Pulsating Heat Pipes Using a Self-Rewetting Fluid

2009 ◽  
Author(s):  
K. Fumoto ◽  
M. Kawaji
Keyword(s):  
Surface Tension ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heated Surface ◽  
Heat Pipes ◽  
Input Power ◽  
Water Mixture ◽  
Pulsating Heat Pipe ◽  
Maximum Heat ◽  
Heat Transport Capability

New experimental results have been obtained on the enhancement of heat transport by a pulsating heat pipe (PHP) using a self-rewetting fluid. Self-rewetting fluids have a property that the surface tension increases with temperature unlike other common liquids. The increasing surface tension at a higher temperature could cause the liquid to be drawn towards a heated surface if a dry spot appears, and improving boiling heat transfer. In the present experiments, 1-butanol was added to water at a concentration of less than 1 wt% to make the self-rewetting fluid. A pulsating heat pipe made from an extruded multi-port tube was partially filled with the butanol-water mixture and tested for its heat transport capability at different input power levels. The experiments showed that the maximum heat transport capability was enhanced by a factor of four when the maximum heater temperature was limited to 120 °C. Thus, the use of a self-rewetting fluid in a PHP has been shown to be highly effective in improving the heat transport capability of pulsating heat pipes.

The Heat Transport Capacity of Micro Heat Pipes

1998 ◽  
Vol 120 (4) ◽  
pp. 1064-1071 ◽  
Author(s):  
J. M. Ha ◽  
G. P. Peterson
Keyword(s):  
Experimental Data ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heat Pipes ◽  
Original Model ◽  
Semiempirical Model ◽  
Transport Capacity ◽  
Predictive Tool ◽  
Maximum Heat ◽  
Micro Heat Pipes

The original analytical model for predicting the maximum heat transport capacity in micro heat pipes, as developed by Cotter, has been re-evaluated in light of the currently available experimental data. As is the case for most models, the original model assumed a fixed evaporator region and while it yields trends that are consistent with the experimental results, it significantly overpredicts the maximum heat transport capacity. In an effort to provide a more accurate predictive tool, a semi-empirical correlation has been developed. This modified model incorporates the effects of the temporal intrusion of the evaporating region into the adiabatic section of the heat pipe, which occurs as the heat pipe approaches dryout conditions. In so doing, the current model provides a more realistic picture of the actual physical situation. In addition to incorporating these effects, Cotter’s original expression for the liquid flow shape factor has been modified. These modifications are then incorporated into the original model and the results compared with the available experimental data. The results of this comparison indicate that the new semiempirical model significantly improves the correlation between the experimental and predicted results and more accurately represents the actual physical behavior of these devices.

Heat Transport Limitation of a Triangular Micro Heat Pipe

2003 ◽  
Author(s):  
D. Sugumar ◽  
Kek Kiong Tio
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Operating Temperature ◽  
Working Fluid ◽  
Transport Capacity ◽  
Condenser Section ◽  
Micro Heat Pipe ◽  
Evaporator Section ◽  
Higher Temperature ◽  
Specific Temperature

A micro heat pipe will operate effectively by achieving its maximum possible heat transport capacity only if it is to operate at a specific temperature, i.e., design temperature. In reality, micro heat pipe’s may be required to operate at temperatures different from the design temperature. In this study, the heat transport capacity of an equilateral triangle micro heat pipe is investigated. The micro heat pipe is filled optimally with working fluid for a specific design temperature and operated at different operating temperatures. For this purpose, water, pentane and acetone was selected as the working fluids. From the numerical results obtained, it shows that the optimal charge level of the micro heat pipe is dependent on the operating temperature. Furthermore, the results also shows that if the micro heat pipe is to be operated at temperatures other than its design temperature, its heat transport capacity is limited by the occurrence of flooding at the condenser section or dryout at the evaporator section, depending on the operating temperature and type of working fluid. It is observed that when the micro heat pipe is operated at a higher temperature than its design temperature, the heat transport capacity increases but limited by the onset of dryout at the evaporator section. However, the heat transport capacity decreases if it is to be operated at lower temperatures than its design temperature due to the occurrence of flooding at condenser end. From the results obtained, we can conclude that the performance of a micro heat pipe is decreased if it is to be operated at temperatures other than its design temperature.

Study on a Pulsating Heat Pipe With Self-Rewetting Fluid

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Koji Fumoto ◽  
Masahiro Kawaji ◽  
Tsuyoshi Kawanami
Keyword(s):  
Surface Tension ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heated Surface ◽  
Input Power ◽  
Water Mixture ◽  
Pulsating Heat Pipe ◽  
Maximum Heat ◽  
Dry Spot ◽  
Heat Transport Capability

This paper discusses a pulsating heat pipe (PHP) using a self-rewetting fluid. Unlike other common liquids, self-rewetting fluids have the property that the surface tension increases with temperature. The increasing surface tension at a higher temperature can cause the liquid to be drawn toward a heated surface if a dry spot appears and thus to improve boiling heat transfer. In experiments, 1-butanol and 1-pentanol were added to water at a concentration of less than 1 wt % to make self-rewetting fluid. A pulsating heat pipe made from an extruded multiport tube was partially filled with the self-rewetting fluid water mixture and tested for its heat transport capability at different input power levels. The experiments showed that the maximum heat transport capability was enhanced by a factor of 4 when the maximum heater temperature was limited to 110°C. Thus, the use of a self-rewetting fluid in a PHP was shown to be highly effective in improving the heat transport capability of pulsating heat pipes.

Experimental Investigation of the Maximum Heat Transport in Triangular Grooves

1996 ◽  
Vol 118 (3) ◽  
pp. 740-746 ◽  
Author(s):  
H. B. Ma ◽  
G. P. Peterson
Keyword(s):  
Experimental Investigation ◽  
Heat Transport ◽  
Heat Pipes ◽  
Effective Area ◽  
Experimental Results ◽  
Test Facility ◽  
Working Fluid ◽  
Maximum Heat ◽  
Pressure Losses ◽  
Micro Heat Pipes

An experimental investigation was conducted and a test facility constructed to measure the capillary heat transport limit in small triangular grooves, similar to those used in micro heat pipes. Using methanol as the working fluid, the maximum heat transport and unit effective area heat transport were experimentally determined for ten grooved plates with varying groove widths, but identical apex angles. The experimental results indicate that there exists an optimum groove configuration, which maximizes the capillary pumping capacity while minimizing the combined effects of the capillary pumping pressure and the liquid viscous pressure losses. When compared with a previously developed analytical model, the experimental results indicate that the model can be used accurately to predict the heat transport capacity and maximum unit area heat transport when given the physical characteristics of the working fluid and the groove geometry, provided the proper heat flux distribution is known. The results of this investigation will assist in the development of micro heat pipes capable of operating at increased power levels with greater reliability.

Effect of Thin Film Condensation on Thermal Performance of Oscillating Heat Pipes

2006 ◽  
Author(s):  
S. B. Liang ◽  
G. P. Xu
Keyword(s):  
Thin Film ◽  
Liquid Film ◽  
Heat Pipe ◽  
Heat Transport ◽  
Slug Flow ◽  
Thin Liquid Film ◽  
Experimental Studies ◽  
Heat Pipes ◽  
Film Condensation ◽  
Working Fluid

Self-sustainable motions of the slug flow in oscillating heat pipes have been investigated in the paper. Thin film condensation in the capillary channels of the condenser of the oscillating heat pipes was studied. Instability of the thin liquid film on the characteristics of heat pipes was analysed. The extra thermal resistance caused by the thickness of the thin liquid film was taken into account for the numerical simulation of the oscillatory motions of the slug flow in the heat pipes. Saturated temperatures and pressures of the working fluid in the condenser were obtained. Thermoacoustic theory was applied to calculate heat transport through the adiabatic section of the heat pipes. Experimental studies were carried out to understand the heat transfer behaviours of heat pipes. One heat pipe with the working fluid of HFC-134a was evaluated. The heat pipe is made of aluminium plate and has the width of 50 mm and thickness of 1.9 mm. Numerical and experimental results relevant to the heat transport capability of the heat pipe were analysed and compared.

Investigation of a Novel Flat Heat Pipe

2005 ◽  
Vol 127 (2) ◽  
pp. 165-170 ◽  
Author(s):  
Yaxiong Wang ◽  
G. P. Peterson
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Thermal Design ◽  
Experimental Results ◽  
Design Parameters ◽  
Working Fluid ◽  
Transport Capacity ◽  
Maximum Heat ◽  
Mesh Screen ◽  
Flat Heat Pipe

A novel flat heat pipe has been developed to assist in meeting the high thermal design requirements in high power microelectronics, power converting systems, laptop computers and spacecraft thermal control systems. Two different prototypes, each measuring 152.4 mm by 25.4 mm were constructed and evaluated experimentally. Sintered copper screen mesh was used as the primary wicking structure, in conjunction with a series of parallel wires, which formed liquid arteries. Water was selected as the working fluid. Both experimental and analytical investigations were conducted to examine the maximum heat transport capacity and optimize the design parameters of this particular design. The experimental results indicated that the maximum heat transport capacity and heat flux for Prototype 1, which utilized four layers of 100 mesh screen were 112 W and 17.4W/cm2, respectively, in the horizontal position. For Prototype 2, which utilized six layers of 150 mesh screen, these values were 123 W and 19.1W/cm2, respectively. The experimental results were in good agreement with the theoretical predictions for a mesh compact coefficient of C=1.15.

Investigation of Polymer Based Micro Heat Pipes for a Flexible Spacecraft Radiator

2001 ◽  
Author(s):  
D. McDaniels ◽  
G. P. “Bud” Peterson
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Power Density ◽  
Polymeric Material ◽  
Heat Dissipation ◽  
Effective Conductivity ◽  
Chemical Reactivity ◽  
Working Fluid ◽  
Maximum Heat ◽  
Micro Heat Pipe

Abstract In response to the space industry’s pursuit of interplanetary travel and a continuous human presence in space, there is increasing focus on spacecraft that change configuration while in space. Flexible thermal radiators are being developed to accommodate various collapse and deployment mechanisms. An analytical model suggests that a lightweight polymeric material with imbedded micro heat pipe arrays can meet heat dissipation requirements while contributing less mass than competing flexible materials. The capillary pumping limit is evaluated as a function of operating temperature using two candidate working fluids. Using water, the maximum heat transport is 18 mW per channel at 140/160 °C. The maximum heat transport using methanol is 2.2 mW at 120 °C, an order-of magnitude difference. A thermal circuit model translates heat transport per channel into total radiator capacity as a function of source temperature and environmental sink temperature. Using water as the working fluid, the radiator capacity was shown to vary from 6.0 kW to 12.2 kW for source temperatures of 20 °C to 50 °C. For source temperatures of 40 °C and higher, the capacity meets or exceeds the dissipation requirements of a reference spacecraft design. While evaluated, methanol is not recommended as a working fluid because its radiator capacity is two to three times lower than water. Although thermal system constraints place limits on the micro heat pipe operating range, design changes directed at alleviating capillary limitations should increase radiator capacity. Technical issues for further study include effects of film billowing, performance limitations related to vapor viscosity, working fluid diffusion, and chemical reactivity between case and working fluid. Compared to a competing graphite fiber weave, the polymeric material has an effective conductivity over ten times higher. Its area power density (in kW/m2) is 18% to 60% lower than the graphite weave, but its mass power density (in kW/kg) is several times higher. Greater flexibility and lower weight also make it more amenable to structural integration. Recently developed space-stable polymers offer resistance to harsh temperature and radiation environments, helping to clear the path toward a more extensive use of polymers within the space industry.

Sign in / Sign up

Export Citation Format

Share Document