scholarly journals Turbulent Flow and Heat Transfer in Gas Turbine Blade Cooling Passages

1992 ◽  
Author(s):  
F. J. Cunha
Keyword(s):  
Heat Transfer ◽  
Turbulent Flow ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Temperature Fields ◽  
Air Cooling ◽  
Turbine Blade Cooling ◽  
Gas Turbine Blades ◽  
Analysis Methodology

A numerical analysis methodology has been created to predict the heat transfer within the air cooling passages of gas turbine blades. In this paper, the turbulent flow heat convection with developed velocity and temperature fields is studied for cavities with turbulators. The influence of Coriolis forces and rotational buoyancy effects were also included. The k-equation turbulence model was employed over most of the cross section while a modified Van Driest’s version of the mixing length hypothesis is used in the near-wall sublayer. This methodology was successfully benchmarked against experimental results for air cooling passages of turbine blades. Analytical results are presented in terms of the Reynolds, Rossby and rotational Rayleigh numbers for realistic operating conditions.

Determination of Heat Transfer Coefficients Around a Blade Surface From Temperature Measurements

1979 ◽  
Author(s):  
D. K. Mukherjee
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Main Stream ◽  
Blade Surface ◽  
Transfer Coefficients ◽  
Gas Turbine Blades ◽  
Heat Transfer Coefficients

To design cooled gas turbine blades, heat transfer coefficients around its surface are required. The calculated heat transfer data under operating conditions in the turbine are often inaccurate and require experimental verification. A method is presented here to determine the heat transfer coefficients around the blade surface and in the coolant channels. This requires measurements of the main stream and coolant temperatures together with the outer surface temperature distribution at varying mass flows. In order to conduct these tests in a gas turbine, test blades have to be specially prepared allowing the variation and measurement of coolant mass flow.

Performance Study of a 1 MW Gas Turbine Using Variable Geometry Compressor and Turbine Blade Cooling

2010 ◽  
Author(s):  
Cleverson Bringhenti ◽  
Jesuino Takachi Tomita ◽  
Joa˜o Roberto Barbosa
Keyword(s):  
Gas Turbine ◽  
Guide Vane ◽  
Turbine Blades ◽  
Axial Flow ◽  
Operating Conditions ◽  
Inlet Guide Vane ◽  
Variable Geometry ◽  
Performance Study ◽  
Turbine Blade Cooling ◽  
Blade Cooling

This work presents the performance study of a 1 MW gas turbine including the effects of blade cooling and compressor variable geometry. The axial flow compressor, with Variable Inlet Guide Vane (VIGV), was designed for this application and its performance maps synthesized using own high technological contents computer programs. The performance study was performed using a specially developed computer program, which is able to numerically simulate gas turbine engines performance with high confidence, in all possible operating conditions. The effects of turbine blades cooling were calculated for different turbine inlet temperatures (TIT) and the influence of the amount of compressor-bled cooling air was studied, aiming at efficiency maximization, for a specified blade life and cooling technology. Details of compressor maps generation, cycle analysis and blade cooling are discussed.

scholarly journals Calculation of Convective Heat Transfer in Square-Sectioned Gas Turbine Blade Cooling Channels

1998 ◽  
Author(s):  
Arash Saidi ◽  
Bengt Sundén
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Cross Sections ◽  
Turbine Blades ◽  
Solution Procedure ◽  
Navier Stokes ◽  
Internal Cooling ◽  
Turbine Blade Cooling ◽  
Cooling Channels ◽  
Energy Equations

Internal cooling channels are commonly used to reduce the thermal loads on the gas turbine blades to improve overall efficiency. In this study a numerical investigation has been carried out to provide a validated and consistent method to deal with the prediction of the fluid flow and the heat transfer of such channels with square cross sections. The rotation modified Navier-Stokes and energy equations together with a low-Re number version of the k-ε turbulence model are solved with appropriate boundary conditions. The solution procedure is based on a numerical method using a collocated grid, and the pressure-velocity coupling is handled by the SIMPLEC algorithm. The computations are performed with the assumption of fully developed periodic conditions. The calculations are carried out for smooth ducts with and without rotation and effects of rotation on the heat transfer are described. Similar numerical calculations have carried out for channels with rib-roughened walls. The obtained results are compared with available experimental data and empirical correlations for the heat transfer rate and the friction factor. Some details of the flow and heat transfer fields are also presented.

Experimental Study of Heat Transfer in Gas Turbine Blades Using a Transient Inverse Technique

2009 ◽  
Vol 30 (13) ◽  
pp. 1077-1086 ◽  
Author(s):  
Peter Heidrich ◽  
Jens V. Wolfersdorf ◽  
Martin Schnieder
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Inverse Technique ◽  
Gas Turbine Blades

Laminar and Transitional Boundary Layer Structures in Accelerating Flow With Heat Transfer

1986 ◽  
Vol 108 (1) ◽  
pp. 116-123 ◽  
Author(s):  
K. Rued ◽  
S. Wittig
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Pressure Gradients ◽  
Transfer Coefficients ◽  
Gas Turbine Blades ◽  
Heat Transfer Coefficients ◽  
Layer Structures ◽  
Flow Heat

The accurate prediction of heat transfer coefficients on cooled gas turbine blades requires consideration of various influence parameters. The present study continues previous work with special efforts to determine the separate effects of each of several parameters important in turbine flow. Heat transfer and boundary layer measurements were performed along a cooled flat plate with various freestream turbulence levels (Tu = 1.6−11 percent), pressure gradients (k = 0−6 × 10−6), and cooling intensities (Tw/T∞ = 1.0−0.53). Whereas the majority of previously available results were obtained from adiabatic or only slightly heated surfaces, the present study is directed mainly toward application on highly cooled surfaces as found in gas turbine engines.

scholarly journals Prediction of Film Cooling Effectiveness of Steam

1982 ◽  
Author(s):  
Je-Chin Han ◽  
P. E. Jenkins
Keyword(s):  
Film Cooling ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Air Cooling ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Gas Turbine Blades ◽  
Fluid Properties ◽  
Three Dimensional Models

The intent of this work is to show, analytically, that superheated steam can provide better film cooling than conventional air for gas turbine blades and vanes. Goldstein’s two-dimensional and Eckert’s three-dimensional models have been reexamined and modified in order to include the effects of thermal-fluid properties of foreign gas injection on the film cooling effectiveness. Based on the modified models, the computed results for steam film cooling effectiveness, showing an increase of 80 to 100 percent when compared with air cooling at the same operating conditions, are presented.

Experimental and Numerical Study of Jet Impingement Cooling for Improved Gas Turbine Blade Internal Cooling With In-Line and Staggered Nozzle Arrays

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Abdel Rahman Salem ◽  
Farah Nazifa Nourin ◽  
Mohammed Abousabae ◽  
Ryoichi S. Amano
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Turbine ◽  
Numerical Study ◽  
Turbine Blades ◽  
Jet Impingement ◽  
Target Surface ◽  
Internal Cooling ◽  
Impingement Cooling ◽  
Gas Turbine Blades

Abstract Internal cooling of gas turbine blades is performed with the combination of impingement cooling and serpentine channels. Besides gas turbine blades, the other turbine components such as turbine guide vanes, rotor disks, and combustor wall can be cooled using jet impingement cooling. This study is focused on jet impingement cooling, in order to optimize the coolant flow, and provide the maximum amount of cooling using the minimum amount of coolant. The study compares between different nozzle configurations (in-line and staggered), two different Reynold's numbers (1500 and 2000), and different stand-off distances (Z/D) both experimentally and numerically. The Z/D considered are 3, 5, and 8. In jet impingement cooling, the jet of fluid strikes perpendicular to the target surface to be cooled with high velocity to dissipate the heat. The target surface is heated up by a direct current (DC) power source. The experimental results are obtained by means of thermal image processing of the captured infra-red (IR) thermal images of the target surface. Computational fluid dynamics (CFD) analysis were employed to predict the complex heat transfer and flow phenomena, primarily the line-averaged and area-averaged Nusselt number and the cross-flow effects. In the current investigation, the flow is confined along with the nozzle plate and two parallel surfaces forming a bi-directional channel (bi-directional exit). The results show a comparison between heat transfer enhancement with in-line and staggered nozzle arrays. It is observed that the peaks of the line-averaged Nusselt number (Nu) become less as the stand-off distance (Z/D) increases. It is also observed that the fluctuations in the stagnation heat transfer are caused by the impingement of the primary vortices originating from the jet nozzle exit.

Sign in / Sign up

Export Citation Format

Share Document