scholarly journals An Experimental Study of Tip Clearance Flow in a Radial Inflow Turbine

1998 ◽  
Author(s):  
R. Dambach ◽  
H. P. Hodson ◽  
I. Huntsman
Keyword(s):  
Tip Clearance ◽  
Leakage Flow ◽  
Hot Wire ◽  
Tip Leakage Flow ◽  
Axial Turbine ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Radial Turbine ◽  
Clearance Flow ◽  
Radial Inflow Turbine

This paper describes an experimental investigation of tip clearance flow in a radial inflow turbine. Flow visualisation and static pressure measurements were performed. These were combined with hot-wire traverses into the tip gap. The experimental data indicates that the tip clearance flow in a radial turbine can be divided into three regions. The first region is located at the rotor inlet, where the influence of relative casing motion dominates the flow over the tip. The second region is located towards midchord, where the effect of relative casing motion is weakened. Finally a third region exists in the exducer, where the effect of relative casing motion becomes small and the leakage flow resembles the tip flow behaviour in an axial turbine. Integration of the velocity profiles showed that there is little tip leakage in the first part of the rotor because of the effect of scraping. It was found that the bulk of tip leakage flow in a radial turbine passes through the exducer. The mass flow rate, measured at four chordwise positions, was compared with a standard axial turbine tip leakage model. The result revealed the need for a model suited to radial turbines. The hot-wire measurements also indicated a higher tip gap loss in the exducer of the radial turbine. This explains why the stage efficiency of a radial inflow turbine is more affected by increasing the radial clearance than by increasing the axial clearance.

1998 Turbomachinery Committee Best Paper Award: An Experimental Study of Tip Clearance Flow in a Radial Inflow Turbine

1999 ◽  
Vol 121 (4) ◽  
pp. 644-650 ◽  
Author(s):  
R. Dambach ◽  
H. P. Hodson ◽  
I. Huntsman
Keyword(s):  
Tip Clearance ◽  
Leakage Flow ◽  
Hot Wire ◽  
Tip Leakage Flow ◽  
Axial Turbine ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Radial Turbine ◽  
Clearance Flow ◽  
Radial Inflow Turbine

This paper describes an experimental investigation of tip clearance flow in a radial inflow turbine. Flow visualization and static pressure measurements were performed. These were combined with hot-wire traverses into the tip gap. The experimental data indicate that the tip clearance flow in a radial turbine can be divided into three regions. The first region is located at the rotor inlet, where the influence of relative casing motion dominates the flow over the tip. The second region is located toward midchord, where the effect of relative casing motion is weakened. Finally, a third region exists in the exducer, where the effect of relative casing motion becomes small and the leakage flow resembles the tip flow behavior in an axial turbine. Integration of the velocity profiles showed that there is little tip leakage in the first part of the rotor because of the effect of scraping. It was found that the bulk of tip leakage flow in a radial turbine passes through the exducer. The mass flow rate, measured at four chordwise positions, was compared with a standard axial turbine tip leakage model. The result revealed the need for a model suited to radial turbines. The hot-wire measurements also indicated a higher tip gap loss in the exducer of the radial turbine. This explains why the stage efficiency of a radial inflow turbine is more affected by increasing the radial clearance than by increasing the axial clearance.

Numerical Simulation of Tip Clearance Control in Axial Turbine Rotor: Part 2—Passive Control of Five Different Tip Platforms

2008 ◽  
Author(s):  
Wei Li ◽  
Wei-Yang Qiao ◽  
Kai-Fu Xu ◽  
Hua-Ling Luo
Keyword(s):  
Flow Control ◽  
Passive Control ◽  
Suction Side ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow

The tip leakage flow has significant effects on turbine in loss production, aerodynamic efficiency, etc. Then it’s important to minimize these effects for a better performance by adopting corresponding flow control. The active turbine tip clearance flow control with injection from the tip platform is given in Part-1 of this paper. This paper is Part-2 of the two-part papers focusing on the effect of five different passive turbine tip clearance flow control methods on the tip clearance flow physics, which consists of a partial suction side squealer tip (Partial SS Squealer), a double squealer tip (Double Side Squealer), a pressure side tip shelf with inclined squealer tip on a double squealer tip (Improved PS Squealer), a tip platform extension edge in pressure side (PS Extension) and in suction side (SS Extension) respectively. Combined with the turbine rotor and the numerical method mentioned in Part 1, the effects of passive turbine tip clearance flow controls on the tip clearance flow were sequentially simulated. The detailed tip clearance flow fields with different squealer rims were described with the streamline and the velocity vector in various planes parallel to the tip platform or normal to the tip leakage vortex core. Accordingly, the mechanisms of five passive controls were put in evidence; the effects of the passive controls on the turbine efficiency and the tip clearance flow field were highlighted. The results show that the secondary flow loss near the outer casing including the tip leakage flow and the casing boundary layer can be reduced in all the five passive control methods. Comparing the active control with the passive control, the effect brought by the active injection control on the tip leakage flow is evident. The turbine rotor efficiency could be increased via the rational passive turbine tip clearance flow control. The Improved PS Squealer had the best effect on turbine rotor efficiency, and it increased by 0.215%.

Measurement and Prediction of Tip Clearance Flow in Linear Turbine Cascades

1993 ◽  
Vol 115 (3) ◽  
pp. 376-382 ◽  
Author(s):  
F. J. G. Heyes ◽  
H. P. Hodson
Keyword(s):  
Experimental Studies ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Pressure Gradients ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Turbine Cascades ◽  
Axial Turbines

This paper describes a simple two-dimensional model for the calculation of the leakage flow over the blade tips of axial turbines. The results obtained from calculations are compared with data obtained from experimental studies of two linear turbine cascades. One of these cascades has been investigated by the authors and previously unpublished experimental data are provided for comparison with the model. In each of the test cases examined, excellent agreement is obtained between the experimental and predicted data. Although ignored in the past, the importance of pressure gradients along the blade chord is highlighted as a major factor influencing the tip leakage flow.

Numerical Investigation of Tip Clearance Flow in an Axial Compressor Cascade

2014 ◽  
Vol 599-601 ◽  
pp. 368-371
Author(s):  
Zhi Hui Xu ◽  
He Bin Lv ◽  
Ru Bin Zhao
Keyword(s):  
Computational Simulation ◽  
Suction Side ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Compressor Cascade ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Blade Tip

Using blade tip winglet to control the tip leakage flow has been concerned in the field of turbomachinery. Computational simulation was conducted to investigate the phenomenological features of tip clearance flow. The simulation results show that suction-side winglet can reduce leakage flow intensity. The tip winglet can also decrease tip leakage mass flow and weaken tip leakage flow mixing with the mainstream and therefore reduce the total pressure loss at the blade tip.

Numerical simulation of unsteady tip clearance flow in an isolated axial compressor rotor blades row

2011 ◽  
Vol 226 (1) ◽  
pp. 82-93 ◽  
Author(s):  
R Taghavi-Zenouz ◽  
S Eslami
Keyword(s):  
Experimental Data ◽  
Axial Compressor ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow

Three-dimensional unsteady numerical simulations were carried out to analyse tip clearance flow in a low-speed isolated axial compressor rotor blades row. A flow solver has been used for the current study utilizing the large eddy simulation (LES) technique. Periodic tip leakage flow and its propagation trajectories were simulated in detail. A number of pseudo pressure transducers were imposed on the pressure side of the blade for detection of unsteady surface pressures to provide a calculation of tip leakage flow frequencies. Two different sizes of tip clearance were considered for simulations and analyses. Non-dimensional frequencies of the tip leakage flow were calculated and final results were compared to those of existing numerical and experimental data. Final results demonstrated that in contrast to the Reynolds averaged Navier–Stokes (RANS) model, the LES method shows considerable dependency of frequency characteristics of the tip leakage flow to the gap size and can detect different frequency spectrums along the blade surface. All the results obtained through the current numerical approach were in close agreement with those of existing experimental data.

Tip Leakage Flow in Radial Inflow Rotor of a Microturbine With Varying Blade-Shroud Clearance

2007 ◽  
Author(s):  
Qinghua Deng ◽  
Jiufang Niu ◽  
Zhenping Feng
Keyword(s):  
Three Dimensional ◽  
Flow Simulation ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Transverse Mass ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow

In this paper, tip clearance flow in a radial inflow turbine rotor under the stage environment is investigated using a three-dimensional viscous flow simulation with three different blade-shroud gap heights of 1%, 2% and 3% of the local span. The results indicate that more relative casing motion increases the scraping effect on tip leakage flow at the rotor entrance. Also, the scraping flow can dominate the whole tip clearance at the rotor entrance when the velocity is high enough at the rotor tip diameter. Regardless of the transverse mass flow rates of the three tip clearances, the results strongly exhibit the characteristics of linearity when the relative meridional length S is greater than 40%. According to the analysis of leakage flow fields in the tip clearance, measures such as a circumference slot, axial slot, or honeycomb are proposed to be applied and placed at the shroud surface over the exducer of the rotor for effectively reducing the transverse flow.

Mechanism of the Interaction Between Casing Treatment and Tip Leakage Flow in a Subsonic Axial Compressor

2006 ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yanhui Wu
Keyword(s):  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through

The use of slots and grooves in the shroud over the tips of compressor blades, known as casing treatment, is known as a powerful method to control tip leakage flow through the clearance gap and enhance the flow stability in compressors. This paper present a detailed steady and unsteady numerical studies of the coupled flow through rotor blade passages and two different types of casing treatment for a modern subsonic axial-flow compressor rotor. Particular attention was given to examining the interaction between the tip leakage flow and the casing treatment. In order to validate the multi block model applied in the rotor blade end-wall region, the computational results for the modern subsonic compressor rotor both with and without casing treatment were correlated with available experimental test data for estimation of the global performance. Detailed analyses of the flow visualization at the tip have exposed the different tip flow topologies between the cases with casing treatment and with untreated smooth wall. It was found that the primary stall margin enhancement afforded by the casing treatment is a result of the tip clearance flow manipulation. The repositioning of the tip clearance vortex further towards the trailing edge of the blade passage and delaying the movement of incoming/tip clearance flow interface to the leading edge plane are the physical mechanisms responsible for extending the compressor stall margin.

scholarly journals The Measurement and Prediction of the Tip Clearance Flow in Linear Turbine Cascades

1992 ◽  
Author(s):  
F. J. G. Heyes ◽  
H. P. Hodson
Keyword(s):  
Experimental Studies ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Pressure Gradients ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Turbine Cascades ◽  
Axial Turbines

This paper describes a simple two-dimensional model for the calculation of the leakage flow over the blade tips of axial turbines. The results obtained from calculations are compared with data obtained from experimental studies of two linear turbine cascades. One of these cascades has been investigated by the authors and previously unpublished experimental data is provided for comparison with the model. In each of the test cases examined, excellent agreement is obtained between the experimental and predicted data. Although ignored in the past, the importance of pressure gradients along the blade chord is highlighted as a major factor influencing the tip leakage flow.

Method for Non-Dimensional Tip Leakage Flow Characterization in Radial Turbines

2018 ◽  
Author(s):  
José Ramón Serrano ◽  
Roberto Navarro ◽  
Luis Miguel García-Cuevas ◽  
Lukas Benjamin Inhestern
Keyword(s):  
Suction Side ◽  
Tip Clearance ◽  
Navier Stokes ◽  
The Novel ◽  
Tip Leakage Flow ◽  
Navier Stokes Equation ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Wide Range ◽  
Clearance Flow

Tip leakage loss characterization and modeling plays an important role in small size radial turbine research. The momentum of the flow passing through the tip gap is highly related with the tip leakage losses. The ratio of fluid momentum driven by the pressure gradient between suction side and pressure side and the fluid momentum caused by the shroud friction has been widely used to analyze and to compare different sized tip clearances. However, the commonly used number for building this momentum ratio lacks some variables, as the blade tip geometry data and the viscosity of the used fluid. To allow the comparison between different sized turbocharger turbine tip gaps, work has been put into finding a consistent characterization of radial tip clearance flow. Therefore, a non-dimensional number has been derived from the Navier Stokes Equation. This number can be calculated like the original ratio over the chord length. Using the results of wide range CFD data, the novel tip leakage number has been compared with the traditional and widely used ratio. Furthermore, the novel tip leakage number can be separated into three different non-dimensional factors. First, a factor dependent on the radial dimensions of the tip gap has been found. Second, a factor defined by the viscosity, the blade loading, and the tip width has been identified. Finally, a factor that defines the coupling between both flow phenomena. These factors can further be used to filter the tip gap flow, obtained by CFD, with the influence of friction driven and pressure driven momentum flow.

Effect of clearance height on tip leakage flow reduced by a honeycomb tip in a turbine cascade

2018 ◽  
Vol 233 (10) ◽  
pp. 3564-3576
Author(s):  
Fu Chen ◽  
Yunfeng Fu ◽  
Jianyang Yu ◽  
Yanping Song
Keyword(s):  
Flow Resistance ◽  
Flow Characteristics ◽  
Tip Clearance ◽  
Small Scale ◽  
Leakage Flow ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Vortex Movement

In this paper, the control mechanism of the honeycomb tip structure on the tip leakage flow of a turbine cascade is studied experimentally and numerically, and the sensitivity of tip leakage flow characteristics to different clearance heights from 0.5% to 2% based on the blade span are mainly discussed. A flat tip is considered as a comparative case. The results show that a part of the leakage flow enters the tip honeycomb cavity, forming small-scale vortices and mixes with the upper leakage fluid, which increases the flow resistance within the clearance. In the range of clearance height variation investigated, honeycomb tip structure can effectively reduce the leakage flow, and reduce the size and strength of the leakage vortex, so that the loss of the cascade is reduced. At a large tip clearance height, the unstable split of the vortex cores causes the vortex in the honeycomb cavities near pressure side to grow in size, so that the vortex extends further into the upper gap, where the turbulent blocking effect of the vortices on the leakage flow is increased. However, due to the vortex movement and the mixing between honeycomb vortices and the upper clearance flow, there is no obvious advantage in reducing the total loss of the cascade compared to the small tip clearance height.

Sign in / Sign up

Export Citation Format

Share Document