Evolution of the Tip Leakage Vortex in an Axial Compressor Rotor

2004 ◽  
Author(s):  
Baojie Liu ◽  
Xianjun Yu ◽  
Hongwei Wang ◽  
Huoxing Liu ◽  
Haokang Jiang ◽  
...  
Keyword(s):  
Large Scale ◽  
Vortex Breakdown ◽  
Swirling Flow ◽  
Cross Flow ◽  
Axial Compressor ◽  
Stereoscopic Particle Image Velocimetry ◽  
Small Scale ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor

The evolution of tip leakage vortex is analyzed at both design and near stall conditions based on instantaneous and averaged velocity and vorticity distributions in cross flow sections measured with Stereoscopic Particle Image Velocimetry (SPIV) in a large-scale low-speed compressor facility. Formation, becoming unstable, and interaction of small-scale vortices and mainstream characterize the evolution of the tip leakage vortex in the compressor rotor. These processes influence the mainstream in very different ways. The process of leakage vortex becoming unstable is relatively smooth at design condition and vortex breakdown occurs at near stall condition for the case in the experiment. The main reason is that the critical condition occurs only in the core of tip leakage vortex at near stall condition. The effect of Coriolis force and centrifugal force on the stability of tip leakage vortex is analyzed theoretically with hypothesis of incompressible, inviscid and quasi-cylindrical swirling flow.

Experimental Investigation of Unsteady Flow Field in the Tip Region of an Axial Compressor Rotor Passage at Near Stall Condition With SPIV

2003 ◽  
Author(s):  
Baojie Liu ◽  
Hongwei Wang ◽  
Huoxing Liu ◽  
Hongjun Yu ◽  
Haokang Jiang ◽  
...  
Keyword(s):  
Large Scale ◽  
Cross Flow ◽  
Axial Compressor ◽  
Light Sheet ◽  
Stereoscopic Particle Image Velocimetry ◽  
Flow Section ◽  
Suction Surface ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Corner Vortex

Stereoscopic Particle Image Velocimetry (SPIV) was applied to a large-scale low-speed compressor facility with the configuration of the two CCD cameras placed on each side of the light sheet to make the measurement of the vortices in the cross flow section possible and to avoid the disturbance from the light sheet containing periscope-type probe. Instantaneous velocity and vorticity distributions were successfully documented at the tip region of the rotor at near stall condition. The measurement results clearly revealed the generation and evolution of the tip leakage vortex. Comparing to design condition, the tip leakage vortex at near stall condition generates and breaks down earlier and interacts more violently with mainstream, which causes large blockage and much loss. Whether corner vortex exists or not is the primary difference between near stall and design condition. Differing from the leakage vortex, the corner vortex is composed of multiple vortices developed from the suction surface of the rotor blade. The key mechanism for the generation of the corner vortex is that the rotation of the rotor has different effect on the evolution of positive vortices and negative vortices, which makes the positive vortices dissipates faster than the negative ones, the vortices at the rotor exit therefore bear mainly negative vortices, which induces the fluids to rotate clockwise at the corner and forms the corner vortex.

Numerical Investigation of Relation Between Unsteady Behavior of Tip Leakage Vortex and Rotating Disturbance in a Transonic Axial Compressor Rotor

2008 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
H. Sasaki
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Rotating Instability

The purpose of this study is to have a better understanding of the unsteady behavior of tip clearance flow at near-stall condition from a multi-passage simulation and to clarify the relation between such unsteadiness and rotating disturbance. This study is motivated by the following concern. A single passage simulation has revealed the occurrence of the tip leakage vortex breakdown at near-stall condition in a transonic axial compressor rotor, leading to the unsteadiness of the tip clearance flow field in the rotor passage. These unsteady flow phenomena were similar to those in the rotating instability, which is classified in one of the rotating disturbances. In other words it is possible that the tip leakage vortex breakdown produces a rotating disturbance such as the rotating instability. Three-dimensional unsteady RANS calculation was conducted to simulate the rotating disturbance in a transonic axial compressor rotor (NASA Rotor 37). The four-passage simulation was performed so as to capture a short length scale disturbance like the rotating instability and the spike-type stall inception. The simulation demonstrated that the unsteadiness of tip leakage vortex, which was derived from the vortex breakdown at near-stall condition, invoked the rotating disturbance in the rotor, which is similar to the rotating instability.

Unsteady Three-Dimensional Flow Phenomena Due to Breakdown of Tip Leakage Vortex in a Transonic Axial Compressor Rotor

2004 ◽  
Author(s):  
K. Yamada ◽  
M. Furukawa ◽  
T. Nakano ◽  
M. Inoue ◽  
K. Funazaki
Keyword(s):  
Shock Wave ◽  
Flow Field ◽  
Vortex Breakdown ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor

Unsteady three-dimensional flow fields in a transonic axial compressor rotor (NASA Rotor 37) have been investigated by unsteady Reynolds-averaged Navier-Stokes simulations. The simulations show that the breakdown of the tip leakage vortex occurs in the compressor rotor because of the interaction of the vortex with the shock wave. At near-peak efficiency condition small bubble-type breakdown of the tip leakage vortex happens periodically and causes the loading of the adjacent blade to fluctuate periodically near the leading edge. Since the blade loading near the leading edge is closely linked to the swirl intensity of the tip leakage vortex, the periodic fluctuation of the blade loading leads to the periodic breakdown of the tip leakage vortex, resulting in self-sustained flow oscillation in the tip leakage flow field. However, the tip leakage vortex breakdown is so weak and small that it is not observed in the time-averaged flow field at near-peak efficiency condition. On the other hand, spiral-type breakdown of the tip leakage vortex is caused by the interaction between the vortex and the shock wave at near-stall operating condition. The vortex breakdown is found continuously since the swirl intensity of tip leakage vortex keeps strong at near-stall condition. The spiral-type vortex breakdown has the nature of self-sustained flow oscillation and gives rise to the large fluctuation of the tip leakage flow field, in terms of shock wave location, blockage near the rotor tip and three-dimensional separation structure on the suction surface. It is found that the breakdown of the tip leakage vortex leads to the unsteady flow phenomena near the rotor tip, accompanying large blockage effect in the transonic compressor rotor at the near-stall condition.

J051024 Asymmetric Flow Behavior Due to Tip Leakage Vortex Breakdown at Near-Stall in an Axial Compressor Rotor

2012 ◽  
Vol 2012 (0) ◽  
pp. _J051024-1-_J051024-5
Author(s):  
Hiroaki KIKUTA ◽  
Yuuki ISHITOBI ◽  
Yasunori HARA ◽  
Masato FURUKAWA ◽  
Kazutoyo YAMADA ◽  
...  
Keyword(s):  
Vortex Breakdown ◽  
Flow Behavior ◽  
Axial Compressor ◽  
Asymmetric Flow ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor

Effects of Tip Clearance on the Stall Inception Process in an Axial Compressor Rotor

2013 ◽  
Author(s):  
Kazutoyo Yamada ◽  
Hiroaki Kikuta ◽  
Masato Furukawa ◽  
Satoshi Gunjishima ◽  
Yasunori Hara
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Stall Inception ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Flow Phenomena ◽  
Casing Pressure

The paper presents experimental and numerical studies on the effects of tip clearance on the stall inception process in a low-speed axial compressor rotor with a large tip clearance. It has been revealed that in the small tip clearance case, shortly after the spike disturbance which results from the leading-edge separation near the rotor tip appears, the tornado-like vortex is generated by the separation, and soon the compressor falls into stall. In the large tip clearance case, the experiment showed that the performance characteristic differs from that in the small tip clearance case at near-stall conditions. This implies that the stall inception process differs with the tip clearance size. The flow phenomenon in the stall inception leading to such difference has been investigated in this study. Pressure and velocity fields which were ensemble-averaged and phase-locked by the periodic multi-sampling technique were measured on the casing wall and downstream of the rotor, respectively. In addition, to capture the unsteady flow phenomena inside the rotor, “Instantaneous Casing Pressure Field Measurement” was carried out: instantaneous casing pressure fields in one rotor passage region were measured by 30 high response pressure transducers mounted on the casing wall. In order to investigate further details of near-stall flow field for the large tip clearance, DES (Detached Eddy Simulation) has been conducted using a computational mesh with 120 million points. The results are compared with those from previous studies for the small tip clearance. As expected, the measurement results show notable differences in the near-stall flow field between the two tip clearance cases. The results from the casing pressure measurement show that high pressure fluctuation appears on the pressure side near the rotor leading-edge in the large tip clearance case. In the result of the velocity field measurement downstream of the rotor, high turbulence intensity is found near the casing in the large tip clearance case. The numerical results reveal that the vortex breakdown occurs in the tip leakage vortex and induces the oscillation of the tip leakage vortex with its unsteady nature. The flow phenomena confirmed in the experimental results are clearly explained by considering the breakdown of the tip leakage vortex. The vortex breakdown gives rise to not only large blockage but also the rotating disturbance through the interaction of the fluctuating tip leakage vortex with the pressure surface of the adjacent blade, and governs the stall inception process.

Study of the Standard k-ε Model for Tip Leakage Flow in an Axial Compressor Rotor

2016 ◽  
Vol 33 (4) ◽  
Author(s):  
Yanfei Gao ◽  
Yangwei Liu ◽  
Luyang Zhong ◽  
Jiexuan Hou ◽  
Lipeng Lu
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Turbulent Viscosity ◽  
Axial Compressor ◽  
Leakage Flow ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Compressor Rotor

AbstractThe standard k-ε model (SKE) and the Reynolds stress model (RSM) are employed to predict the tip leakage flow (TLF) in a low-speed large-scale axial compressor rotor. Then, a new research method is adopted to “freeze” the turbulent kinetic energy and dissipation rate of the flow field derived from the RSM, and obtain the turbulent viscosity using the Boussinesq hypothesis. The Reynolds stresses and mean flow field computed on the basis of the frozen viscosity are compared with the results of the SKE and the RSM. The flow field in the tip region based on the frozen viscosity is more similar to the results of the RSM than those of the SKE, although certain differences can be observed. This finding indicates that the non-equilibrium turbulence transport nature plays an important role in predicting the TLF, as well as the turbulence anisotropy.

scholarly journals Anisotropic Characteristics of Turbulence Dissipation in Swirling Flow: A Direct Numerical Simulation Study

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Xingtuan Yang ◽  
Nan Gui ◽  
Gongnan Xie ◽  
Jie Yan ◽  
Jiyuan Tu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Energy Dissipation ◽  
Direct Numerical Simulation ◽  
Large Scale ◽  
Isotropic Turbulence ◽  
Vortex Breakdown ◽  
Swirling Flow ◽  
Turbulent Energy ◽  
Swirling Flows ◽  
Small Scale

This study investigates the anisotropic characteristics of turbulent energy dissipation rate in a rotating jet flow via direct numerical simulation. The turbulent energy dissipation tensor, including its eigenvalues in the swirling flows with different rotating velocities, is analyzed to investigate the anisotropic characteristics of turbulence and dissipation. In addition, the probability density function of the eigenvalues of turbulence dissipation tensor is presented. The isotropic subrange of PDF always exists in swirling flows relevant to small-scale vortex structure. Thus, with remarkable large-scale vortex breakdown, the isotropic subrange of PDF is reduced in strongly swirling flows, and anisotropic energy dissipation is proven to exist in the core region of the vortex breakdown. More specifically, strong anisotropic turbulence dissipation occurs concentratively in the vortex breakdown region, whereas nearly isotropic turbulence dissipation occurs dispersively in the peripheral region of the strong swirling flows.

Characteristics of the Tip Leakage Vortex in a Low-Speed Axial Compressor With Different Rotor Tip Gaps

2012 ◽  
Author(s):  
Zhibo Zhang ◽  
Xianjun Yu ◽  
Baojie Liu
Keyword(s):  
Axial Compressor ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Stereoscopic Particle Image Velocimetry ◽  
Tip Clearance ◽  
Test Facility ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage

The detailed evolutionary processes of the tip leakage flow/vortex inside the rotor passage are still not very clear for the difficulties of investigating of them by both experimental and numerical methods. In this paper, the flow fields near the rotor tip region inside the blade passage with two tip gaps, 0.5% and 1.5% blade height respectively, were measured by using stereoscopic particle image velocimetry (SPIV) in a large-scale low speed axial compressor test facility. The measurements are conducted at four different operating conditions, including the design, middle, maximum static pressure rise and near stall conditions. In order to analyze the variations of the characteristics of the tip leakage vortex (TLV), the trajectory, concentration, size, streamwise velocity, and the blockage parameters are extracted from the ensemble-averaged results and compared at different compressor operating conditions and tip gaps. The results show that the formation of the TLV is delayed with large tip clearance, however, its trajectory moves much faster in an approximately linear way from the blade suction side to pressure side. In the tested compressor, the size of the tip gap has little effects on the scale of the TLV in the spanwise direction, on the contrary, its effects on the pitch-wise direction is very prominent. Breakdown of the TLV were both found at the near-stall condition with different tip gaps. The location of the initiation of the TLV breakdown moves downstream from the 60% chord to 70% chord as the tip gap increases. After the TLV breakdown occurs, the flow blockage near the rotor tip region increases abruptly. The peak value of the blockage effects caused by the TLV breakdown is doubled with the tip gap size increasing from 0.5% to 1.5% blade span.

101 Interaction of Tip Leakage Vortex with Shock Wave in a Transonic Axial Compressor Rotor

2000 ◽  
Vol 2000.53 (0) ◽  
pp. 1-2
Author(s):  
Kazutoyo YAMADA ◽  
Yoshinori TAGUCHI ◽  
Kazuhisa SAIKI ◽  
Masato FURUKAWA ◽  
Masahiro INOUE
Keyword(s):  
Shock Wave ◽  
Axial Compressor ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Transonic Axial Compressor

Effects of Tip Clearance Size on Flowfield in a Low-Speed Axial Compressor Rotor

2014 ◽  
Vol 543-547 ◽  
pp. 158-163 ◽  
Author(s):  
Zhen Zhen Duan ◽  
Yang Wei Liu ◽  
Li Peng Lu
Keyword(s):  
Flow Condition ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Primary Role ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Overall Performance ◽  
Corner Vortex

The simulations of a low-speed axial compressor rotor with two tip clearance sizes, 0.5% chord and 1.5% chord, were performed in the study. Overall performance and detailed flow fields at near stall condition are analyzed. The results show that the rotor stall occurs at higher mass flow condition with large tip clearance. For the small tip clearance the tip leakage vortex and the corner vortex both contribute significantly to the rotor stall, and the interaction between the vortices promotes the stall generation. While for the large tip clearance the tip leakage vortex plays a primary role, and the vortices interaction is ignorable.

Sign in / Sign up

Export Citation Format

Share Document