An Innovative Passive Tip-Leakage Control Method for Axial Turbines: Linear Cascade Wind Tunnel Results

2008 ◽  
Author(s):  
Markus Hamik ◽  
Reinhard Willinger
Keyword(s):  
Wind Tunnel ◽  
Turbine Blade ◽  
Working Fluid ◽  
Leakage Flow ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Blade Tip ◽  
Tip Injection ◽  
Tip Desensitization

Depending on the blade aspect ratio, tip-leakage losses can contribute up to one third of the total losses in an axial turbine blade row. In unshrouded turbine blade rows, the radial gaps allow working fluid to pass from the pressure to the suction sides. This tip-leakage flow does not contribute to the work output of the turbine stage. Therefore, any technique which tends to reduce tip-leakage losses has the objective to decrease the flow through the tip gaps. A frequently used method of reducing the tip-leakage flow is the modification of the blade tip geometry by so-called squealers or winglets. Since this method decreases the sensitivity of tip-leakage losses on tip gap width, it is called tip desensitization. This paper presents a new method for tip desensitization: the passive blade tip injection. A low speed cascade wind tunnel is used for experimental investigations. Geometry of the turbine cascade is the up-scale of the tip section of a gas turbine rotor row. Three different gap widths in the range from 0.85% to 2.50% chord length are used. Total pressure, static pressure and flow angles are obtained by traversing a pneumatic five-hole probe about 0.3 axial chord lengths downstream of the turbine cascade. For investigations of the tip injection effect, a single blade of the cascade is modified by an injection channel. Based on experimental results, it is shown that the passive tip injection method decreases tip-leakage losses. At small tip gaps, this reduction can be rather significant. Finally, the positive influence of blade tip injection on tip-leakage losses is described by an analytical model based on the discharge coefficient.

Blade Tip Leakage Loss Reduction by Means of Passive Tip Injection: Linear Cascade Wind Tunnel Results

2017 ◽  
Author(s):  
Jonas Rejek ◽  
Stefan aus der Wiesche ◽  
Reinhard Willinger
Keyword(s):  
Wind Tunnel ◽  
Turbine Blade ◽  
Working Fluid ◽  
Slight Reduction ◽  
Loss Reduction ◽  
Leakage Loss ◽  
Linear Cascade ◽  
Tip Leakage ◽  
Blade Tip ◽  
Tip Injection

In the open literature, an innovative concept for turbine blade tip leakage loss reduction by means of passive tip injection was recently proposed. The present paper presents experimental results obtained for an unshrouded turbine blade corresponding to a 50 % reaction stage. The experiments were performed in a low-speed linear cascade wind tunnel facility with air as working fluid. The effect of passive tip injection on the resulting loss was investigated by detailed five-hole-probe measurements. Cascades with three different tip gap heights and blades with and without passive injection were considered. Special attention was spent to the actual upstream conditions. The detailed flow field measurements showed that at the blade tip exit the leakage flow merged with the main flow and rolled up to a tip leakage vortex. The linear cascade wind tunnel results indicated a slight reduction of the resulting total pressure loss coefficient due to the passive tip injection. The observed tip leakage loss reduction was well comparable with the predictions of simplified analytical model.

Tip Leakage Flow Reduction of a Linear Turbine Cascade Using String-Type DBD Plasma Actuators

2018 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Takehiko Segawa
Keyword(s):  
Reynolds Number ◽  
Plasma Actuators ◽  
Leakage Flow ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Dbd Plasma ◽  
Tip Leakage ◽  
String Type ◽  
Displacement Thickness ◽  
Blade Tip

Tip leakage flow through the small gap between the blade tip of a turbine and the casing endwall reduces the aerodynamic performance. String-type dielectric barrier discharge (DBD) plasma actuators made of silicone printed-circuit board were used for the active control of the tip leakage flow of a linear turbine cascade. Sinusoidal voltage excitation with amplitude varying from 4 kV to 6 kV (peak-to-peak voltage: 8 kVp-p to 12 kVp-p) and fixed frequency of 10 kHz was applied to the plasma actuators. The two-dimensional velocity field in the blade passage was estimated by particle image velocimetry (PIV) under the very low Reynolds number conditions of Re = 7.1 × 103 and 1.42 × 104. The tip leakage flow was reduced by the flow control using plasma actuators. The high turbulence intensity region caused by the tip leakage flow was also reduced. For the quantitative comparisons, the displacement thickness of the absolute velocity distributions was examined. By the flow control of the plasma actuators, the displacement thickness at tip-side gradually decreased as the input voltage increased. Although three types of plasma actuators were used, with thin, thick, and flat electrodes and different ratios of discharge area, the differences in their effect were negligible. The reason for these very small differences in effect is the wide spread of the plasma discharge from the encapsulated electrode in the plasma actuator to the exposed electrode of the blade tip. At the relatively high Reynolds number condition of Re = 1.42 × 104, the effect of the plasma actuator was smaller than that at the lower Reynolds number condition of Re = 7.1 × 103.

Effect of Turbine Blade Tip Cooling Configuration on Tip Leakage Flow and Heat Transfer

2020 ◽  
Vol 142 (2) ◽  
Author(s):  
Sergen Sakaoglu ◽  
Harika S. Kahveci
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Gas Turbines ◽  
Thermal Response ◽  
Thermal Conditions ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Blade Tip

Abstract The pressure difference between suction and pressure sides of a turbine blade leads to tip leakage flow, which adversely affects the first-stage high-pressure (HP) turbine blade tip aerodynamics. In modern gas turbines, HP turbine blade tips are exposed to extreme thermal conditions requiring cooling. If the coolant jet directed into the blade tip gap cannot counter the leakage flow, it will simply add up to the pressure losses due to leakage. Therefore, the compromise between the aerodynamic loss and the gain in tip-cooling effectiveness must be optimized. In this paper, the effect of tip-cooling configuration on the turbine blade tip is investigated numerically from both aerodynamics and thermal aspects to determine the optimum configuration. Computations are performed using the tip cross section of GE-E3 HP turbine first-stage blade for squealer and flat tips, where the number, location, and diameter of holes are varied. The study presents a discussion on the overall loss coefficient, total pressure loss across the tip clearance, and variation in heat transfer on the blade tip. Increasing the coolant mass flow rate using more holes or by increasing the hole diameter results in a decrease in the area-averaged Nusselt number on the tip floor. Both aerodynamic and thermal response of squealer tips to the implementation of cooling holes is superior to their flat counterparts. Among the studied configurations, the squealer tip with a larger number of cooling holes located toward the pressure side is highlighted to have the best cooling performance.

Effect of Turbine Blade Tip Cooling Configuration on Tip Leakage Flow and Heat Transfer

2019 ◽  
Author(s):  
Sergen Sakaoglu ◽  
Harika S. Kahveci
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Gas Turbines ◽  
Thermal Response ◽  
Thermal Conditions ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Blade Tip

Abstract The pressure difference between suction and pressure sides of a turbine blade leads to the so-called phenomenon, the tip leakage flow, which most adversely affects the first-stage high-pressure (HP) turbine blade tip aerodynamics. In modern gas turbines, HP turbine blade tips are also exposed to extreme thermal conditions requiring the use of tip cooling. If the coolant jet directed into the blade tip gap cannot counter the leakage flow, it will simply add up to the pressure losses due to this leakage flow. Therefore, it is necessary to handle the design of tip cooling in such a way that the compromise between the aerodynamic loss and the gain in the tip cooling effectiveness is optimized. In this paper, the effect of tip cooling configuration on the turbine blade tip is investigated numerically both from the aerodynamics and thermal aspects in order to determine the optimum tip cooling configuration. The studies are carried out using the tip cross-section of General Electric E3 (Energy Efficient Engine) HP turbine first-stage blade for two different tip geometries, squealer tip and flat tip, where the number, location, and diameter of the cooling holes are varied. The study presents a discussion on the overall loss coefficient, the total pressure loss across the tip clearance, and the variation of heat transfer on the blade tip. The aerodynamic and heat transfer results are compared with the experimental data from literature. It is observed that increasing the coolant mass flow rate by using more holes or by increasing the hole diameter results in a decrease in the area-averaged Nusselt number on the tip floor, as expected. The findings show that both aerodynamic and thermal response of the squealer tips to the implementation of cooling holes is superior to their flat counterparts. Among the studied configurations, the squealer tip with larger number of cooling holes located towards the pressure side is highlighted as the configuration having the best cooling performance.

Characteristics of Tip Leakage Flow of the Turbine Blade With Cutback Squealer and Coolant Injection

2010 ◽  
Author(s):  
Jianhua Wang ◽  
Yalin Liu ◽  
Xiaochun Wang ◽  
Zhineng Du ◽  
Shijie Yang
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Flow Characteristics ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Coolant Injection ◽  
Blade Tip ◽  
Film Cooling Holes ◽  
Numerical Program

Experimental and numerical investigations of the tip leakage flow characteristics between turbine blade tip and stator wall (shroud) were conducted by a particle image velocimetry (PIV) system and the commercially available software CFX 11.0. A three-time scaled profile of the GE-E3 blade was used as specimen. Two rows of cylindrical film-cooling holes with 1.5mm diameter were arranged in the blade tip. One row with 5 holes was placed in pressure side just below the groove floor, and the other with 11 holes was equidistantly arranged on the tip along the mid camber line. To exhibit the generation and movement of leakage vortex, and to compare the coolant injection effects from different rows, several typical velocity profiles were captured by the PIV system. The experimental results were used as a data source to validate the turbulence model and numerical program. To better understand the mixing characteristics of the coolant injected from different rows with the leakage flow, the fluid fields of the leakage vortex and coolant flow were simulated, and the leakage mass rates from the blade tip in different coolant injection cases and different gaps were quantitatively estimated by the validated numerical program.

Impact of Passive Tip-Injection on Tip-Leakage Flow in Axial Low Pressure Turbine Stage

2015 ◽  
Author(s):  
Pouya Ghaffari ◽  
Reinhard Willinger ◽  
Sabine Bauinger ◽  
Andreas Marn
Keyword(s):  
Aerodynamic Resistance ◽  
Low Pressure ◽  
Leakage Flow ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Low Pressure Turbine ◽  
Blade Tip ◽  
Tip Injection ◽  
The Impact

In addition to geometrical modifications of the blade tip for reducing tip-leakage mass flow rate the method of passive tip-injection serves as an aerodynamic resistance towards the tip-leakage flow. The impact of this method has been investigated thoroughly at unshrouded blades in linear cascades. Furthermore combinations of shrouded blades with passive tip-injection have been investigated analytically as well as via numerical simulations for incompressible flow in linear cascades. The objective of this paper is to consider a real uncooled low pressure turbine stage with shrouded blades and to investigate the effect of passive tip-injection on various operational characteristics. CFD calculations have been carried out in a rotational frame taking into consideration compressible flow and serve for evaluating the method of passive tip-injection in the given turbine stage. Experimental data obtained from the machine without tip-injection serve as boundary conditions for the CFD calculations.

Effect of arbitrary blade tip design on tip leakage flow

2019 ◽  
Vol 234 (1) ◽  
pp. 19-30
Author(s):  
Jiahui Jin ◽  
Yanping Song ◽  
Jianyang Yu ◽  
Fu Chen
Keyword(s):  
Flow Rate ◽  
Total Pressure ◽  
Leakage Flow ◽  
Exit Section ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Pressure Loss Coefficient ◽  
Blade Tip ◽  
Total Pressure Loss Coefficient

Tip geometry modification is frequently used to suppress the tip leakage flow in the turbine cascade however a universally beneficial tip geometry modification design has not been fully discovered. In this paper, the two-surface coupling arbitrary blade tip design method in three-dimensional physical space which satisfies the simple trigonometric function law is proposed and the mathematical parametric description is presented. The effects of different arbitrary blade tips on tip leakage flow have been studied numerically in a highly loaded axial turbine cascade. The aerodynamic performance of different tips is assessed by the tip leakage mass flow rate and the total pressure loss coefficient at the exit section. The Kriging model and genetic optimization algorithm are used to optimize the arbitrary blade tips to obtain the optimal arbitrary blade tip. Compared with the flat tip, the tip leakage mass flow rate is decreased by 10.57% and the area-average total pressure loss coefficient at the exit section is reduced by 8.91% in the optimal arbitrary blade tip.

Sign in / Sign up

Export Citation Format

Share Document