Sensitivity Analysis and Experimental Validation of Transient Performance Predictions for a Short-Range Turbofan

2016 ◽  
Author(s):  
Maria V. Culmone ◽  
Nicolás Garcia-Rosa ◽  
Xavier Carbonneau
Keyword(s):  
Short Range ◽  
Engine Performance ◽  
Sensitivity Study ◽  
Simulation Software ◽  
Tip Clearance ◽  
Mass Storage ◽  
Transient Effects ◽  
Transient Model ◽  
Blade Tip ◽  
The Impact

Transient effects are important features of engine performance calculations. The aim of this paper is to analyze a new, fully transient model implemented using the PRopulsion Object Oriented Simulation Software (PROOSIS) for a civil, short range turbofan engine. A transient turbofan model, including the mechanical inertia effect has been developed in PROOSIS. Specific physical effects such as heat soakage, mass storage, blade tip clearance and combustion delay have been implemented in the relevant components of PROOSIS to obtain a fully transient model. Since a large number of components are concerned by all the transient effects, an influence study is presented to determine which are the most critical effects, and in which components. Inertia represents the relevant phenomenon, followed by thermal effects, combustion delay and finally mass storage. The comparison with experimental data will provide a first validation of the model. Finally a sensitivity study is reported to assess the impact of uncertain knowledge of key input parameters in the response time prediction accuracy.

scholarly journals The Impact of Realistic Casing Geometries and Clearances on Fan Blade Tip Aerodynamics

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Alistair John ◽  
Ning Qin ◽  
Shahrokh Shahpar
Keyword(s):  
Engine Performance ◽  
Leading Edge ◽  
Tip Clearance ◽  
Blade Design ◽  
Engine Operation ◽  
Surface Method ◽  
Flow Features ◽  
Blade Tip ◽  
Fan Blade ◽  
The Impact

During engine operation, fan casing abradable liners are worn by the blade tip, resulting in the formation of trenches. This paper describes the influence of these trenches on the fan blade tip aerodynamics. A detailed understanding of the fan tip flow features for cropped and trenched clearances is first developed. A parametric model is then used to model trenches in the casing above the blade tip and varying blade tip positions. It is shown that increasing clearance via a trench reduces performance by less than increasing clearance through cropping the blade tip. A response surface method is then used to generate a model that can predict fan efficiency for a given set of clearance and trench parameters. This model can be used to influence fan blade design and understand engine performance degradation in service. It is shown that an efficiency benefit can be achieved by increasing the amount of tip rubbing, leading to a greater portion of the tip clearance sat within the trench. It is shown that the efficiency sensitivity to clearance is biased toward the leading edge (LE) for cropped tips and the trailing edge (TE) for trenches.

A Simplified Method to Evaluate the Impact of Component Design on Engine Performance

2007 ◽  
Author(s):  
Francesco Montella ◽  
J. P. van Buijtenen
Keyword(s):  
Design Process ◽  
Engine Performance ◽  
Simulation Software ◽  
Fast Method ◽  
Engine Simulation ◽  
Engine Model ◽  
Component Design ◽  
Wide Range ◽  
Engine Component ◽  
The Impact

This paper presents a simplified and fast method to evaluate the impact of a single engine component design on the overall performance. It consists of three steps. In the first step, an engine system model is developed using available data on existing engines. Alongside the cycle reference point, a sweep of operating points within the flight envelop is simulated. The engine model is tuned to match a wide range of conditions. In the second step, the module that contains the engine component of interest is analyzed. Different correlations between the component design and the module efficiency are investigated. In the third step, the deviations in efficiency related to different component configurations are implemented in the engine baseline model. Eventually, the effects on the performances are evaluated. The procedure is demonstrated for the case of a two-spool turbofan. The effects of tip leakage in the low pressure turbine on the overall engine performance are analyzed. In today’s collaborative engine development programs, the OEMs facilitate the design process by using advanced simulation software, in-house available technical correlations and experience. Suppliers of parts have a limited influence on the design of the components they are responsible for. This can be rectified by the proposed methodology and give subcontractors a deeper insight into the design process. It is based on commercially available PC engine simulation tools and provides a general understanding of the relations between component design and engine performance. These relations may also take into account of aspects like production technology and materials in component optimization.

EGR System Performance Optimization of Diesel Engine Based on GT-Power and Fluent Co-Simulation

2013 ◽  
Vol 860-863 ◽  
pp. 1703-1709 ◽  
Author(s):  
Xian Jun Hou ◽  
Shu Chen ◽  
Zhi'en Liu
Keyword(s):  
Diesel Engine ◽  
Flow Field ◽  
Performance Optimization ◽  
Engine Performance ◽  
Simulation Software ◽  
Field Analysis ◽  
Three Dimension ◽  
Air Inlet ◽  
Inlet Position ◽  
The Impact

A calculation model of turbocharged diesel engine was developed based on one-dimension simulation software GT-power,which can provide a steady boundary condition for the flow field analysis of EGR system.The three-dimension simulation software Fluent was applied in establishing the flow field model of the air-intake system under different air inlet position to analize the distribution of the exhaust gas,and then obtained the impact of the EGRs air-inlet position to uniformity of EGR system, thereby we could acquire the parameters which achieves the best maching between the EGR system and the diesel engine, it also provided a reference for engine performance optimization.

scholarly journals Study on the Mechanism of a Carrier-based Engine Parts' Performance Decline and Its Impact on the Whole Engine Performance

2018 ◽  
Vol 179 ◽  
pp. 01012
Author(s):  
Wu Heng ◽  
Li Benwei ◽  
Zhao Shufan ◽  
Wang Yonghua
Keyword(s):  
High Pressure ◽  
Engine Performance ◽  
Tip Clearance ◽  
Flow Capacity ◽  
Influence Area ◽  
Time Operation ◽  
Long Time ◽  
Performance Decline ◽  
Turbulence Effect ◽  
The Impact

The technical approach "use – parts' change - engine performance change" has been adopted to study and analyse the gas unit parts' performance changes of an engine after a long time operation. The mechanism of performance decline of the turbine is analysed based on the numerical simulation, the impact of components' performance decline on overall engine performance is studied and the correlation analysis is carried out. The results show that the change of turbine tip clearance, roughness increase and surface change will lead to the enhancement of secondary flow and the increase of influence area, and the turbulence effect is strengthened, resulting in the decrease of turbine circulation capacity and efficiency. The booster ratio of high pressure compressor, the flow capacity of high pressure and low pressure turbines, the flow capacity and efficiency of fan are the major component parameters causing the overall engine performance's degradation. And it also provides theoretical basis for the prevention of engine performance's degradation and online washing of parts and the whole machine.

Effect of blade tip grooving on the performance of an axial fan at different tip clearances in the absence and presence of inlet guide vanes

2019 ◽  
Vol 234 (1) ◽  
pp. 72-84
Author(s):  
Masoud Kharati-Koopaee ◽  
Hossein Moallemi
Keyword(s):  
Numerical Study ◽  
Guide Vane ◽  
Pressure Coefficient ◽  
Tip Clearance ◽  
Axial Fan ◽  
Guide Vanes ◽  
Inlet Guide Vanes ◽  
Blade Tip ◽  
Torque Coefficient ◽  
The Impact

This research aims at the numerical study of the blade tip grooving effect on the performance of a ducted axial fan at different tip clearances in the absence and presence of inlet guide vanes. To do this, significant parameters of the fan (i.e. pressure and torque coefficients as well as fan efficiency) comprising single- and double-grooved tips are evaluated and compared with those of the original fan. Validation of the considered numerical model is performed through comparison of the numerical findings with experimental results of a single-stage ducted fan, which comprises a set of 37 guide vane and 24-blade rotor rotating at the speed of 3600 r/min. Results reveal that grooving the blade tip causes the fan parameters to increase and higher fan parameters could be attained adopting single-grooved tip. It is shown that employing grooved blades causes the sensitivity of fan parameters to the change in the tip clearance to diminish. Results exhibit that the impact of grooving the blade on the reduction of sensitivity of fan parameters to the change in the tip clearance for the single-grooved tip in the absence of guide vanes is more remarkable than the other cases and in this case, as the tip clearance increases from the lower to the upper considered value, the decreased percentages in pressure coefficient, torque coefficient, and fan efficiency are 29.8%, 8.9%, and 22.8%, respectively. Numerical findings show that the influence of grooving the blade on the fan parameters in the presence of guide vanes is lower than that without guide vanes and in the presence of guide vanes, the highest average increase percentages in pressure coefficient, torque coefficient, and fan efficiency relative to those of the original fan, which is observed in the single grooved tip, are 3.1%, 1.4%, and 1.7%, respectively.

Integration of 3D-CFD Component Simulation Into Overall Engine Performance Analysis for Engine Condition Monitoring Purposes

2018 ◽  
Author(s):  
C. Klein ◽  
F. Wolters ◽  
S. Reitenbach ◽  
D. Schönweitz
Keyword(s):  
Performance Analysis ◽  
Condition Monitoring ◽  
Guide Vane ◽  
Engine Performance ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Inlet Guide Vane ◽  
Cfd Model ◽  
The Impact ◽  
Engine Condition

For an efficient detection of single or multiple component damages, the knowledge of their impact on the overall engine performance is crucial. This knowledge can be either built up on measurement data, which is hardly available to non-manufacturers or –maintenance companies, or simulative approaches such as high fidelity component simulation combined with an overall cycle analysis. Due to a high degree of complexity and computational effort, overall system simulations of jet engines are typically performed as 0-dimensional thermodynamic performance analysis, based on scaled generic component maps. The approach of multi-fidelity simulation, allows the replacement of single components within the thermodynamic cycle model by higher-order simulations. Hence, the component behavior becomes directly linked to the actual hardware state of the component model. Hereby the assessment of component deteriorations in an overall system context is enabled and the resulting impact on the overall system can be quantified. The purpose of this study is to demonstrate the capabilities of multi fidelity simulation in the context of engine condition monitoring. For this purpose, a 0D-performance model of the IAE-V2527 engine is combined with a CFD model of the appropriate fan component. The CFD model comprises the rotor as well as the outlet guide vane of the bypass and the inlet guide vane of the core section. As an exemplarily component deterioration, the fan blade tip clearance is increased in multiple steps and the impact on the overall engine performance is assessed for typical engine operating conditions. The harmonization between both simulation levels is achieved by means of an improved map scaling approach using an optimization strategy leading to practicable simulation times.

Effects of Turbine Tip Clearance on Gas Turbine Performance

2008 ◽  
Author(s):  
Cleverson Bringhenti ◽  
Joa˜o Roberto Barbosa
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Engine Performance ◽  
Outer Wall ◽  
Tip Clearance ◽  
Large Space ◽  
Steady State Condition ◽  
Turbine Engine ◽  
Wall Boundary Layer ◽  
Blade Tip

There are many different sources of loss in gas turbines. The turbine tip clearance loss is the focus of this work. In gas turbine components such as compressor and turbine the presence of rotating blades necessitates a small annular tip clearance between the rotor blade tip and the outer casing. This clearance, although mechanically necessary, may represent a source of large loss in a turbine. The gap height can be a fraction of a millimeter but can have a disproportionately high influence on the stage efficiency. A large space between the blades and the outer casing results in detrimental leakages, while contact between them can damage the blades. Therefore, the evaluation of the sources of the performance degradation independently presents useful information that can aid in the maintenance action. As part of the overall blade loss the turbine tip clearance loss arises because at the blade tip the gas does not follow the intended path and therefore does not contribute to the turbine power output and interacts with the outer wall boundary layer. Increasing turbine tip clearance causes performance deterioration of the gas turbine and therefore increases fuel consumption. The increase in turbine tip clearance may as a result of rubs during engine transients and the interaction between the blades and the outer casing. This work deals with the study of the influence of the turbine tip clearance on a gas turbine engine, using a turbine tip clearance model incorporated to an engine deck. Actual data of an existing engine were used to check the validity of the procedure. This paper refers to a single shaft turbojet engine under development, operating under steady state condition. Different compressor maps were used to study the influence of the curve shapes on the engine performance. Two cases were considered for the performance simulation: constant corrected speed and constant maximum cycle temperature.

Evaluating Gas Turbine Performance Using Machine-Generated Data: Quantifying Degradation and Impacts of Compressor Washing

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Uyioghosa Igie ◽  
Pablo Diez-Gonzalez ◽  
Antoine Giraud ◽  
Orlando Minervino
Keyword(s):  
Gas Turbine ◽  
Measurement Data ◽  
Engine Performance ◽  
Large Data ◽  
Simulation Software ◽  
Engine Operation ◽  
Compressor Inlet ◽  
Data Points ◽  
Global And Local ◽  
The Impact

Gas turbine (GT) operators are often met with the challenge of utilizing and making meaning of the vast measurement data collected from machine sensors during operation. This can easily be about 576 × 106 data points of gas path measurements for one machine in a base load operation in a year, if the width of the data is 20 columns of measured and calculated parameters. This study focuses on the utilization of large data in the context of quantifying the degradation that is mostly related to compressor fouling, in addition to investigations on the impact of offline and online compressor washing. To achieve this, four GT engines operating for about 3.5 years with 51 offline washes and 1184 occasions of online washes were examined. This investigation includes different wash frequencies, liquid concentrations, and one engine operation without online washing (only offline). This study has involved correcting measurement data not only just with compressor inlet temperatures (CITs) and pressures but also with relative humidity (RH). turbomatch, an in-house GT performance simulation software has been implemented to obtain nondimensional factors for the corrections. All of the data visualization and analysis have been conducted using tableau analytics software, which facilitates the investigation of global and local events within an operation. The concept of using of handles and filters is proposed in this study, and it demonstrates the level of insight to the data and forms the basis of the outcomes obtained. This work shows that during operation, the engine performance is mostly deteriorating, though to varying degrees. Online washing also showed an influence on this, reducing the average degradation rate each hour by half, when compared to the engine operating only with offline washing. Hourly marginal improvements were also observed with an increased average wash frequency of nine hours and a similar outcome obtained when the washing solution is 2.3 times more concentrated. Clear benefits of offline washes are also presented, alongside the typically obtainable values of increased power output after a wash, also in relation to the number of operating hours before a wash.

Testing the Impact on Emergency Diesel Performance of Water in Diesel Fuel

2016 ◽  
Author(s):  
Robert Cryer ◽  
Mark O’Connell
Keyword(s):  
Diesel Engine ◽  
Water Content ◽  
Diesel Fuel ◽  
Water Contamination ◽  
Nuclear Power ◽  
Engine Performance ◽  
Simulation Software ◽  
Diesel Generator ◽  
Fuel Feed ◽  
The Impact

This paper focuses on testing results of the impact of water contamination in diesel fuel on the ability of an emergency diesel generator (EDG) to successfully start and operate during an emergency. This testing program resulted from the discovery of degraded vent pipes on diesel fuel feed tanks that could have allowed rain water to enter and collect at the bottom of the diesel fuel system and potentially prevent satisfactory engine start-up and operation. The nuclear regulator notified the nuclear plant of a potential yellow finding. The initial analysis effort focused on the use of diesel engine combustion software (Ricardo’s WAVE© 1D engine performance simulation software). Two medium-speed diesel engine models were analyzed with added water content ranging from 10% to 40% water in the diesel fuel. The analyses demonstrated that the engines could start and operate with those percentages of water in the fuel, but that the engine output would experience a power loss or derate proportional to the water content. The regulator was not convinced that the analysis was sufficient. The validity of the analytical findings above was demonstrated by full-scale tests conducted by MPR Associates on a large diesel engine. To accomplish this, Entergy, the nuclear power plant owner constructed a simulation of the diesel fuel supply system at a facility having the same make and model EDG. Water was introduced into the diesel fuel day tank by two different approaches; slow trickle flow and large slugs of water. These conditions simulated either a steady rainfall while the EDG was operating or a large volume of water collected in the system while the EDG was in standby. Under both water contamination scenarios, which consisted of more than 50 hours of testing, the diesel engine and generator set responded with negligible loss of frequency or voltage. Further, the engine was confirmed to have undergone no increased wear or degradation as a result of the high levels of water in the combustion chambers. Following a detailed review of the test program and the successful results, the regulator concluded that neither a non-cited violation nor a penalty was warranted.

RELATIVE CASING MOTION EFFECT ON SQUEALER TIP COOLING PERFORMANCE AT TIGHT TIP CLEARANCE

2020 ◽  
pp. 1-18
Author(s):  
Diwei Zhu ◽  
Qiang Zhang ◽  
Shaopeng Lu ◽  
Jinfang Teng
Keyword(s):  
Thermal Load ◽  
Tip Clearance ◽  
Cooling Efficiency ◽  
Suction Surface ◽  
Cooling Performance ◽  
High Thermal Load ◽  
Blade Tip ◽  
Motion Effect ◽  
Cfd Method ◽  
The Impact

Abstract The effect of relative motion between the casing and turbine blade tip has been recognized as an important factor for tip aerothermal performance evaluation. Tight tip clearance is becoming one of the main objectives of engine manufacturers. This paper provides some insights on the topic that the impact of casing motion on the blade tip thermal performance could be different between nominal and tight tip clearances. A typical squealer tip geometry was employed, with coolant holes on the cavity floor near the pressure side rim. Three tip clearances, 1.1%, 0.6% and 0.2% of the span, are compared. The CFD method was validated against experimental data in the previous study. The results suggest that, in the tight tip situation, the effect of casing motion on cooling efficiency and flow structure is distinguished from the larger clearance situations. The scraping effect drives the leakage flow towards the blade suction surface, inducing high thermal load at tight clearance. The findings in this study highlight the importance of relative casing motion, especially at tight clearance.

Sign in / Sign up

Export Citation Format

Share Document